Instrukcja obsługi Anda Seat X-Air Pro

Anda Seat krzesło biurowe X-Air Pro

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Anda Seat X-Air Pro (2 stron) w kategorii krzesło biurowe. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
FEATURES
WHAT'S IN THE BOX
ASSEMBLY STEPS
Press the casters into the
wheelbase.
Insert the gas piston into
the wheelbase.
Flip the seat base over, remove
the pre-installed M6×16 bolts and
washers, and use them to install
the tilt mechanism.
Thread the tilt mechanism's
levers through the hole on the
seat base frame and secure them
with ST4×35 screws. Place the gas piston into
the seat base.
Turn the chair upright to
complete the assembly.
Attach the headrest onto the
backrest with M6×16 bolts.
Mount the armrests with M6×25
bolts and washers.
Align the backrest to the seat
base and secure them with
M8×16 bolts and washers.
① ②
③
④
⑤
⑥
⑦
⑧
⑨ ⑩
A
Headrest ×1
B
Backrest ×1
C
Seat Base ×1
D
Tilt mechanism ×1
E
Tilt Mechanism Wire Cover ×1
F
Armrests ×2
G
Gas Piston ×1
J K
Bolts & washers ×3
L
M N O
H
Wheelbase ×1
I
Casters ×1
M8×16
Bolts & washers ×6
M6×25
Bolts ×2
M6×16
Screws ×6
ST4×35
Hex Wrench ×1
M5&M4
Screwdriver ×1
Extendable Seat Depth :
47-53cm extension for optimal
thigh space and comfort.
Rotating Armrests
with 9-Level Heights:
Double-pivot rotation: 360°
for the upper pivot and 220°
for the lower.
Backrest Recline:
105°~126° adaptive recline
with a 4-position tilt lock
for different postures.
3D Headrest:
Up-down adjustability with
double-pivot rotation.
Backrest Height Adjustment:
8cm up-down range in 7 different
levels for customizable support.
Seat Height Adjustment:
10cm height range offering
ideal leg space for all
figures.
E
N
N
B
J
N
K
F
A
LN
G
pre-installed
C
D
N
M
O
I
H
Arrange the tilt mechanism wires
to the hole's sides. Use your
hands to click one end of the wire
cover into the hole, then press
the other end into place using the
included wrench or a flat tool.
HOW TO ADJUST
Hold armrests firmly to:
Move up or down to the ideal height.
Slide forward or backward.
Rotate the upper pivot 360° or the lower pivot 220°.
Armrests:
Pull the left-side lever upward, move the seat
with your hip to the ideal depth, and release the
lever to lock in.
Seat Depth:
To raise: Stand on your feet, pull the height lever
upward, and release to lock in.
To lower: Pull the height lever upward and release
to lock in.
Seat Height(while sitting):
Using both hands, lift the backrest with steady and
gradual force. For the lowest height, lift it rapidly
to the highest and release.
Backrest Height:
Lean back gradually to the desired angle and pull
the recline lever upward to lock in.
Backrest Recline:
Hold with both hands to move it up-down or rotate
30° with front pivot and 38° with back pivot.
Headrest:
ASSEMBLY TIPS
1. Closely follow the Assembly Steps and refer to the illustrations for correct assembly.
2. Check every component in the box and confirm they are in working condition.
3. Safety gloves are recommended for assembly.
4. To prevent accidental component damage, assemble on a clean, even surface with
a protective layer.
5. To prevent misalignment or uneven tightening, install each bolt halfway, adjust if
needed, then fully tighten.
6. The gas piston stays tight in place once it's assembled.
If you need to disassemble the chair and pack it for transportation:
1. Lay it on its side, hold the gas piston firmly, and lightly twitch the seat or tap on
its back side with a rubber hammer until it detaches from the gas piston.
2. Then tap on the wheelbase to get it loose from the gas piston.
Note: Please take safety precautions during this process. Any damage or safety
issue that occurs from it is not covered by this product's warranty.
USAGE TIPS
1. This is a single-person chair. Use it with only one person at a time.
2. Ensure all components are securely fastened before use. Inspect bolt tightness
every 3 months to maintain safety.
3. Place the chair on a level surface. Avoid prolonged exposure to excessive
moisture, heat, or direct sunlight.
4. For seated use only. Do not stand on the chair or sit on its armrests.
5. Clean the chair's surface before your first use. Wipe with a soft cloth only.
6. Avoid cleaners with high acid or alkaline, as they may corrode or damage the
chair surface.
7. Use the chair features as shown in the How To Adjust section.
8. While reclining, lean back gradually and keep yourself balanced. Flinging back too
hard or too far might cause tipping.
9. Do not take apart the gas piston for safety.
FOR THE WINNERS’ CIRCLE
ASSEMBLY GUIDE
X-AIR PRO
MESH
CHAIR

Specyfikacje produktu

Marka: Anda Seat
Kategoria: krzesło biurowe
Model: X-Air Pro

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Anda Seat X-Air Pro, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje krzesło biurowe Anda Seat

Anda Seat

Anda Seat X-Air Pro Instrukcja

17 Grudnia 2024

Instrukcje krzesło biurowe

Najnowsze instrukcje dla krzesło biurowe

Habitat

Habitat Cosmo Instrukcja

8 Października 2024
Ikea

Ikea MATCHSPEL 605.742.84 Instrukcja

8 Października 2024
Ikea

Ikea GRÖNFJÄLL 205.034.82 Instrukcja

8 Października 2024
X Rocker

X Rocker Deluxe 2.0 Instrukcja

8 Października 2024
X Rocker

X Rocker Rogue 2.0 Instrukcja

8 Października 2024
Drift

Drift DR100 Instrukcja

7 Października 2024
Drift

Drift DR200 Instrukcja

7 Października 2024
Ikea

Ikea NILSERIK 704.918.96 Instrukcja

7 Października 2024
Ikea

Ikea FLINTAN 705.925.55 Instrukcja

7 Października 2024
Ikea

Ikea MULLFJÄLLET 704.725.53 Instrukcja

7 Października 2024