Instrukcja obsługi AMX Octaire AVS-OCT-6464-007

AMX system hi-fi Octaire AVS-OCT-6464-007

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla AMX Octaire AVS-OCT-6464-007 (2 stron) w kategorii system hi-fi. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
Installation Guide
CB-TP5i Rough-In Box for NXD-500i 5" Touch Panel
Overview
The CB-TP5i Rough-In Box (FG038-11) is an optional accessory for the NXD-500i
Modero® Wall/Flush Mount Touch Panel. The Rough-In Box allows the panel to be
mounted directly to the studs/pre-wall. The NXD-500i is contained within a plastic
outer housing or back box, and the back box attaches to the Rough-In Box.
Specifications
WARNING: In order to guarantee a stable installation of the NXD-500i, the distance
between the CB-TP5i and the outer wall surface must be a minimum of .50 inches
(1.27cm) and a maximum of .875 inches (2.22cm).
• Refer to the SP62-0038-01 diagram for detailed installation dimensions.
Pre-Wall Installation of the CB-TP5i Rough-In Box
1. Remove the rough-in box cover (A in FIG. 1) before installation of the Rough-In
Box (B). Note: the cover MUST be removed before drywall installation. The
cover may be reinstalled after drywall installation using 4-40 screws (not
included).
2. Attach the optional Back Cover for the CB-TP5i (FG038-12) if necessary, as
required by building codes. (For more information, refer to the Back Cover
Installation section on page 2.)
3. Fasten the CB-TP5i rough-in box to the stud through the holes on the Stud
Mounting tabs (FIG. 2), using either nails or screws (not provided).
4. Remove the appropriate wiring knockouts from the rough-in box to
accommodate the cables being threaded through to the NXD-500i touch panel.
5. Thread the incoming Ethernet and USB wiring through the knockouts. Use of the
left wiring knockouts is recommended with this installation for ease of connection
of the cables to the touch panel. Leave enough slack in the wiring to
accommodate installation of the panel.
6. Install the drywall/sheetrock before inserting the main NXD-500i device into the
CB-TP5i.
7. Cut out the opening for the NXD-500i where the wall has been placed over the
Rough-In Box. Cutting out the surface slightly smaller than what is outlined in the
installation drawings, so that you can make any necessary cutout adjustments, is
very highly recommended.
FIG. 1 CPB-TP5i Rough-In Box - Front and Back Views
CB-TP5i (FG038-11) Specifications
Dimensions (HWD) • 6.73" x 9.30" x 1.43"
• 17.09 cm x 23.62 cm x 3.63 cm
Certifications • UL 508A
Front Rear
Wiring Knockouts
Breakaway Stud
Mounting Flanges
A
B
2 locations to secure cover
after applying drywall
(8-32 x .25 screws)
3 locations to secure cover
after applying drywall
FIG. 2 CB-TP5i - Mounted to Wall Stud
Stud
Recommended Cutout for
CB-TP5i Rough-In Box
For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).
4/11
©2011 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX.
AMX reserves the right to alter specifications without notice at any time.
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com
93-038-11 REV: B
CB-TP5i Top CB-TP5i Break-Away
Side of Rough-In Box
With Break-Away Flanges
Optional Back Cover
for the CB-TP5i (FG038-12)
(Only for areas where
required by building codes.)
Flange detail
Back Cover Installation
Assembly of CB-TP5i and Back Plate
Screws (80-0114-01), #4-20 x .375
CB-TP5i
Back Plate
Note: two screw holes in
flanges at top and bottom
of Back Plate, but one
screw hole per flange on
sides.

Specyfikacje produktu

Marka: AMX
Kategoria: system hi-fi
Model: Octaire AVS-OCT-6464-007

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z AMX Octaire AVS-OCT-6464-007, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje system hi-fi AMX

AMX

AMX Optima AVS-OP-1624-117 Instrukcja

21 Czerwca 2024
AMX

AMX Octaire AVS-OCT-6464-007 Instrukcja

21 Czerwca 2024
AMX

AMX Octaire AVS-OCT-6432-007 Instrukcja

21 Czerwca 2024

Instrukcje system hi-fi

Najnowsze instrukcje dla system hi-fi

AKAI

AKAI EIE Pro Instrukcja

13 Października 2024
Sharp

Sharp XL-540H Instrukcja

11 Października 2024
Kenwood

Kenwood M-9000S Instrukcja

10 Października 2024
GoGen

GoGen MSC 472 BTDAB Instrukcja

9 Października 2024
Morel

Morel SUB-10X Instrukcja

9 Października 2024
Morel

Morel USUB 803 Instrukcja

9 Października 2024
Morel

Morel Soundsub PSW8e-w Instrukcja

9 Października 2024
Morel

Morel Sopran 934 Instrukcja

9 Października 2024
NAD

NAD M10 V3 Instrukcja

9 Października 2024
NUVO

NUVO NV-MPS4-E Instrukcja

8 Października 2024