Instrukcja obsługi AMX FG1052-16

AMX rozgałęźnik FG1052-16

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla AMX FG1052-16 (2 stron) w kategorii rozgałęźnik. Ta instrukcja była pomocna dla 17 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

Quick Start Guide

AutoPatch RGBHV (BNC) DAD Modules

Overview

RGBHV (BNC) DAD (Distribution Amplifier Driver) Modules have either one input and

four outputs for a 1:4 distribution or one input and six outputs for a 1:6 distribution of

RGBHV analog signals. The single RGBHV input is distributed to four or six outputs

over standard cable runs of up to 250 ft. (76.2 m) with no additional equipment

required. Each output can be independently adjusted for gain and peaking to ensure

the proper amount of compensation is provided for each cable run. This guide contains

complete information for this product.

Product Specifications

* Gain and peaking are independent switches that allow the user to turn on or off the

gain and peaking.

Installation

Mounting Options

Desktop – Attach the rubber feet (included) to the bottom of the module.

Rack Mounting

To rack mount a module:

1. Remove one screw from each side of the module as shown in FIG. 3. Do not

reuse screw for rack ear.

2. Attach rack ears as shown in FIG. 3 (screws provided).

3. Place the module in a standard EIA 19 in. (48.26 cm) rack and secure it to the

rack with screws.

Typical Setup

Attaching Cables

To attach connectors:

1. Fasten the BNC connectors from the source and destination devices onto the

BNC connectors on the module (FIG. 5).

2. Attach the power cord into the power receptacle on the module and into an

external AC power source.

3. Press the “I” side of the power switch.

4. Apply power to the source and destination devices.

Note: The power indicator LED is on the module’s front.

FIG. 1 RGBHV (BNC) DAD 1:4 model FG1052-13

FIG. 2 RGBHV (BNC) DAD 1:6 model FG1052-16

General Specifications

Approvals Pending

AC Power

Consumption (max.)

Consumption (typical)

100 to 240 VAC single phase, 50-60 Hz

120 VAC, 650 mA

120 VAC, 100 mA

Operational Temperature 32° to 110° F (0° to 43° C)

Humidity 0 to 90% non-condensing

Dimensions 5.15 in. (13.08 cm) depth

17.40 in. (44.20 cm) width without rack ears

19.00 in. (48.26 cm) width with rack ears

1.72 in. (4.37 cm) 1 RU height without feet

Weight: Approx. 4.5 lbs. (2 kg)

Connector Type BNC

RGBHV Signal Specifications

Frequency Response ±3 dB, 450 MHz or better

Signal to Noise Ratio Vin = 0.7 V, 100% IRE >65 dB

Level

Input (max.)

Output (max.)

±1.75 V

Impedance

Input

Output

75 ohms

Return Loss -45 dB @ 5 MHz

Sync Level

Input (max.)

Output (max.)

0 V to +5 V

Sync Impedance

Input

Output

510 ohms

50 ohms

Gain & Peaking* Specifications

Gain

OFF

Unity

+0.85 dB

Peaking

OFF

No peaking

8 dB @ 150 MHz

8 dB @ 300 MHz

Cable Length (max.) 250 ft. (76.2 m)

FIG. 3 Remove screw and attach rack ears

FIG. 4 Typical system setup using 1:4 DAD

FIG. 5 Attach input and output connectors (1:6 model shown)

Remove screw

Source Device

Destination Devices

1:4 DAD Module

Power

BNCs

From

source To destinations

BNCs

For full warranty information, refer to www.amx.com

12/07

AMX reserves the right to alter specifications without notice at any time.

3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com

93-1052-02 REV: A

Front Panel DIP Switches

Each DIP switch pair controls the output gain and peak of the same-numbered

output signal. The default setting is both switches “Off” (down, FIG. 6), which

represents unity gain and no peaking. The gain and peak adjustments can

compensate for long cable runs. To increase brightness of a destination’s video, set

the gain DIP switch to “On”. To sharpen a destination’s video, set the peak DIP

switch to “On”.

To adjust DIP switches:

1. Using a small screwdriver or paper clip, flip the toggles on the DIP switches up.

See table below for settings.

Flip either or both switches “ON” depending on the length of the cable run.

FIG. 6 Adjust DIP switches for gain and peaking

DIP Switch Settings

OFF (default) ON Result

Gain Unity gain +0.85 dB Brightens image

Peaking No peaking 8 dB @ 150 MHz

8 dB @ 300 MHz Sharpens image

Example:

Outputs 2, 3, & 6 are set to ON for gain & peaking

Outputs 1, 4 & 5 are set to OFF / unity

Specyfikacje produktu

Marka:	AMX
Kategoria:	rozgałęźnik
Model:	FG1052-16
Kolor produktu:	Czarny
Częstotliwość wejściowa AC:	50 - 60 Hz
Wysokość produktu:	44 mm
Szerokość produktu:	483 mm
Głębokość produktu:	131 mm
Waga produktu:	2000 g
Zakres temperatur (eksploatacja):	0 - 43 °C
Zakres wilgotności względnej:	0 - 90 %
Napięcie:	100-240 V
Szerokość pasma:	450 MHz
Wyjścia BNC:	6
Wejścia BNC:	1