Instrukcja obsługi American Dryer GX1-M
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla American Dryer GX1-M (2 stron) w kategorii Narkotyki do rąk. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/2
1 7/8
DISCONNECT POWER BEFORE INSTALLING
DESUNA LA ELECTRICIDAD ANTES DE HACER REPARACIONES
WARNING:
INSTALLATION INSTRUCTIONS
1. Remove cover by removing (2) tamper proof-screws using security wrench
supplied. Pull cover directly toward you. IMPORTANT: Save security wrench.
2. Dryers should be placed at least 2 feet (61cm) apart and at least 12” (30cm) from
washbasin. Do not install dryer over washbasin. Automatic dryers should be at least
18” (46cm) above any projection which may interfere with the operation of the auto-
matic sensor.
Hold the backplate to the wall at the suggested mounting height. Measure from bot-
tom edge of to the backplate floor (Ref. Dimension “A”, Fig. 1):
CHILDREN
MEN WOMEN (depends on age) DISABLED
44” (112cm) 42” (107cm) 32 to 42” (81-107cm) 36” (91cm)
3. Mark the locations of the four mounting holes and the conduit entrance location on the
wall. (The conduit entrance is the proper hole diameter for 1/2 inch (13mm) conduit.)
4. Fasten the backplate to the wall where previously marked.
RECOMMENDATION:
Wood wall – No. 14 (M6) wood screws, 2 3/4” (70mm) long
Cement or brick – 1/4” (M6) stud expansion bolts, 3” (76mm) long
Hollow wall – 1/4” (M6) toggle bolts, length depends on wall thickness
5. Run service wire to the dryer location and connect to lead wires.
IMPORTANT: All units must be supplied with 3 wire service. Use No. 12 or 14 wire
as required by local electrical code. The ground wire must be connected to the dryer
ground screw. Unit must be installed by a qualified licensed electrician.
CONNECT TO A DEDICATED CIRCUIT NOT TO ExCEED 20 AMPS.
Dryers located in shower rooms or other wet locations should be equipped with
ground fault interrupter(s).
6. Carefully replace the cover using (2) tamper-proof screws supplied. Apply a bead of
caulk around edges of cover to wall.
GLOBAL DRYER
MFD by AMERICAN DRYER, INC.
33067 INDUSTRIAL ROAD, LIVONIA, MI 48150, U.S.A.
Telephone (734) 421-2400 • Fax (734) 421-5580
www.americandryer.com • Email: sales@americandryer.com
Revised November 2011
GLOBAL DRYER LIMITED WARRANTY
All parts of the models are warranted to the original consumer purchaser Gx-M/C
to be free from defects in material and workmanship for a period of five (5) years or
three (3) years for models from the date of purchase from manufacturer. Sensor Gx
warranty three (3) years in the U.S.A. All models outside of the U.S.A., one (1) year
including sensor. We will replace FREE OF CHARGE, during the warranty period, any
warranted part which proves defective in material and/or workmanship under normal
installation, use, and service, excluding normal wear. Replacement parts can be
obtained by returning the part, TRANSPORTATION CHARGES PREPAID. You must
notify factory prior to returning part or dryer. Any damage to this dryer as a result of
misuse, abuse, neglect, accident, improper installation, unauthorized repairs, or any
other use violative of instructions furnished by us, WILL VOID THIS WARRANTY.
THIS LIMITED WARRANTY IS THE SOLE WARRANTY ON OUR PRODUCTS, AND
WE DISCLAIM AND EXCLUDE ANY AND ALL OTHER WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE. OUR LIABILITY SHALL NOT EXCEED
IN ANY EVENT THE REPLACEMENT OR SALE PRICE OF THE ALLEGEDLY
NONCONFORMING PRODUCT AND SHALL EXCLUDE LABOR CHARGES. TO
THE EXTENT PERMITTED BY LAW WE SHALL NOT BE LIABLE FOR ANY LOSS,
COST, EXPENSE, OR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY
KIND, WHETHER BASED UPON WARRANTY (EXPRESS OR IMPLIED), CONTRACT,
NEGLIGENCE OR STRICT LIABILITY AND ARISING IN ANY WAY IN CONNECTION
WITH THE DESIGN, MANUFACTURE, SALE, USE OR REPAIR OF THE PRODUCT.
O ’ M wner s anual GX Series Hand Dryers
F Ior nstallatIon or ervIce s
assIstance lease all P c
(734) 421-2400 or
Email: sales@americandryer.com
ImPortant: Have odel erial o eady M & S N . r
m #______ s #______odel erIal
F d Migure 1 - ryer ouNtiNg
®
(48mm)
(208mm)
6 3/16
7/8 (22mm) DIA. IN-WALL
& SURFACE CONDUIT
ENTRANCES
MOUNTING HOLES FOR
1/4” (M6) DIA. SCREWS
(227MM)
8 15/16
7/16
(11mm)
“A”
8 7/16
(214mm)
FLOOR
7/16
(11mm)
SERVICE AND MAINTENANCE OF YOUR DRYER
GENERAL OPERATION
This dryer is activated by an infrared sensor. The dryer operates as long as hands are below
nozzle. There is a maximum 60 second running time with a safety over-ride feature, if hands
are not removed. Each component used in your dryer has been designed to provide years of
trouble-free service. However, if trouble should develop, it can normally be located by visual
examination. Removal or replacement of most parts, is simple and can be done without
special tools.
IF THE DRYER WON’T TURN ON:
Check electrical service, circuit breaker. Make sure proper voltage is being supplied to the
dryer. Check for loose or disconnected terminal to sensor. INCREASE sensitivity (
FIgure 3)
by using a flat-blade screwdriver and CAREFULLY turning the adjustment pot located on the
sensor CLOCKWISE 1/3 Turn MAx. If necessary, replace sensor.
IF DRYER WILL NOT SHUT OFF:
Make certain black foam is attached to lens and lens is clean. If damaged, replace.
DECREASE sensitivity (FIgure 3) by CAREFULLY turning the adjustment pot located on
the sensor. Use a small flat-blade screwdriver. 1/3 Turn MAx. COUNTER-CLOCKWISE. If
necessary, replace sensor.
IF COLD AIR IS COMING FROM THE NOZZLE:
Turn off breaker for 30 seconds to reset thermostat. If required. remove the cover and vent,
check the heating element. If the element is broken or burned out, replace it.
IF NO AIR IS COMING FROM THE NOZZLE AND HEATING ELEMENT GLOWS:
Remove the cover and check to see that the fan revolves freely. Check and replace motor,
if required.
FOR ANY OTHER PROBLEM, CONTACT FACTORY FOR ASSISTANCE.
CLEANING - DO NOT spray cleaning solvents thru dryer vents. DO NOT use abrasive,
chlorinated, or highly alkaline cleaners. DO NOT use oil based cleaners.
SEMI-ANNUALLY remove the cover and clean all lint and dust from the mechanism, inside
of cover, and plastic window.
Clean cover with a mild soap or detergent and warm water, using a soft cloth or sponge.
PARTS LIST FOR YOUR DRYER (Figure 2)
ITEM PART NO. DESCRIPTION
1 GX202 COVER, WHITE ABS
(MUST SPECIFY DRYER MODEL #)
2 GX202-M COVER, WHITE STEEL
(MUST SPECIFY DRYER MODEL#)
3 GX202-BG COVER, BLACK GRAPHITE STEEL
(SPECIFY DRYER MODEL#)
4 GX202-C COVER, CHROME PLATED STEEL
(SPECIFY DRYER MODEL #)
5 GX212 VENT ASS’Y W/ LENS AND FOAM GASKET
6 GX216 MOTOR, 110-120V INCLUDES BLOWER WHEEL (GX1)
7 GX217 MOTOR, 208-240V INCLUDES BLOWER WHEEL (GX3)
8 GX218 HEATING ELEMENT 110-120V (GX1)
9 GX220 HEATING ELEMENT 208-240V (GX3)
10 GX228 BLOWER WHEEL
11 GX239 SENSOR COMPLETE, 110-240 VOLT
12 GB232 TAMPER-PROOF SCREWS & SECURITY WRENCH
F S aigure 3 eNSitivity djuStMeNt
+
-
F vigure 2 - Exploded iew
DISCONNECT POWER BEFORE INSTALLING
DESUNA LA ELECTRICIDAD ANTES DE HACER REPARACIONES
WARNING:
6
7
8
9
1
2
4
3
10
11
5
12
Specyfikacje produktu
| Marka: | American Dryer |
| Kategoria: | Narkotyki do rąk |
| Model: | GX1-M |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z American Dryer GX1-M, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Narkotyki do rąk American Dryer
18 Września 2024
17 Września 2024
12 Września 2024
9 Września 2024
9 Września 2024
8 Września 2024
8 Września 2024
6 Września 2024
5 Września 2024
5 Września 2024
Instrukcje Narkotyki do rąk
- Narkotyki do rąk Honeywell
- Narkotyki do rąk Starmix
- Narkotyki do rąk Dyson
- Narkotyki do rąk Thermex
- Narkotyki do rąk Mitsubishi
- Narkotyki do rąk Stiebel Eltron
- Narkotyki do rąk Royal Sovereign
- Narkotyki do rąk Primo
- Narkotyki do rąk Fantini Cosmi
- Narkotyki do rąk Biodrier
- Narkotyki do rąk Noirot
- Narkotyki do rąk Bobrick
- Narkotyki do rąk Uniprodo
Najnowsze instrukcje dla Narkotyki do rąk
15 Października 2024
28 Września 2024
25 Września 2024
25 Września 2024
25 Września 2024
25 Września 2024
25 Września 2024
25 Września 2024
21 Września 2024
21 Września 2024