Instrukcja obsługi Alto Professional Stealth Wireless
Alto Professional
Bezprzewodowy system audio
Stealth Wireless
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Alto Professional Stealth Wireless (40 stron) w kategorii Bezprzewodowy system audio. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/40
User Guide
English ( 3 – 8 )
Guía del usuario
Español ( 9 – 14 )
Guide d'utilisation
Français ( 15 – 20 )
Guida per l'uso
Italiano ( 21 – 26 )
Benutzerhandbuch
Deutsch ( 27 – 32 )
Gebruikershandleiding
Nederlands ( 33 – 38 )
Appendix
English ( 39 )
2
User Guide (English)
Introduction
Thank you for purchasing the Alto Professional Stealth Wireless system. Stealth Wireless is a
convenient way to carry an audio signal from the main mixing and listening location to your powered
loudspeakers. Compatible with any active loudspeaker, this system can be used to simplify a new
installation or to retrofit an existing sound system. Welcome to the sound of wireless freedom.
Features:
• Wireless audio connectivity to active loudspeakers
• Replaces up to 200' of console-to-system cabling
• No compromise in audio quality
• Reliable UHF band; 16 selectable channels
• Adjustable squelch eliminates interference
• Dual-channel transmitter: two XLR-1/4" combo inputs
• Single-channel receivers: XLR output
• Grow your system using the Stealth Expander Pack (sold separately)
Box Contents
• Stealth Wireless Transmitter (x1)
• Stealth Wireless Receiver (x2)
• Hook and Loop Strips (for receivers)
• M10 Screws (x2)
• Machine Screws (x2)
• Power Adapters (x3)
• User Guide
• Safety & Warranty Manual
Support
For complete system requirements, compatibility information, and product registration, visit the Alto
Professional website: altoprofessional.com.
For additional product support, visit altoprofessional.com/support.
Important
CAUTION! Permanent hearing loss may be caused by exposure to extremely high noise levels. The
U.S. Government's Occupational Safety and Health Administration (OSHA) has specified permissible
exposures to certain noise levels.
According to OSHA, exposure to high sound pressure levels (SPL) in excess of these limits may result
in hearing loss. When using equipment capable of generating high SPL, use hearing protection while
such equipment is under operation. The table below defines exposure for a given duration.
HOURS PER DAY SPL EXAMPLE
8 90 Small gig
6 92 Train
4 95 Subway train
3 97 High level desktop monitors
2 100 Classical music concert
1.5 102 Riveting machine
1 105 Machine factory
.50 110 Airport
.25 or less 115 Rock concert
3
Transmitter Features
Rear Panel
1. Antennas – Place the antennas in a vertical position for best
results in transmitting the wireless signal. If the wireless signal
quality is poor, change the position of the antennas.
2. Combo Inputs – Connect balanced or unbalanced 1/4” or XLR
line-level sources here.
3. Power Connector – Connect the included 12V DC, 300 mA power
adapter here.
Front Panel
1. Power Button – Press this button to turn the
transmitter on/off.
2. Mono/Stereo Select – Adjust this switch to
change the wireless signal that is sent to the
receiver to be either mono/stereo.
3. Signal Clip Indicator – The LED will turn red when the signal is close to peaking (clipping).
Note: The LED will begin to flicker red at -4 dB before clipping and become solid red if clipping
occurs.
4. Channel Select – Adjusts the frequency band range.
• Match channels on the transmitter and receiver in order to get a signal.
• Watch the receiver’s AF indicator and RF indicator to make sure a signal is being received.
• If you receive interference, change to another channel until a clean signal comes through.
• To change the channel:
a. Press and hold the Channel Select button for approximately 1 second until the
channel number flashes.
b. While the channel number is flashing, tap the Channel Select button to cycle through
the 16 available channels. Set the transmitter and receiver(s) to the same channel.
c. When the desired channel number is shown, wait for 3 seconds. When the channel
number stops flashing, that channel is now selected.
d. Use the Left/Right Selector switches to set which receiver receives the left and right
signals, since the left and right signals are sent on the same channel.
5. Trim – Adjusts the signal level.
POWER MONO/ STEREO
LR
MIN MAX MIN MAX
CHANNEL
1
2
3
4
55
1
1
2 2 3
Specyfikacje produktu
| Marka: | Alto Professional |
| Kategoria: | Bezprzewodowy system audio |
| Model: | Stealth Wireless |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Alto Professional Stealth Wireless, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Bezprzewodowy system audio Alto Professional
30 Czerwca 2024
Instrukcje Bezprzewodowy system audio
- Bezprzewodowy system audio Yamaha
- Bezprzewodowy system audio Samsung
- Bezprzewodowy system audio Pioneer
- Bezprzewodowy system audio Muse
- Bezprzewodowy system audio Lenco
- Bezprzewodowy system audio Linksys
- Bezprzewodowy system audio Naim
- Bezprzewodowy system audio Maginon
- Bezprzewodowy system audio Sonos
- Bezprzewodowy system audio Envivo
- Bezprzewodowy system audio Iluv
- Bezprzewodowy system audio Eis
- Bezprzewodowy system audio OXX Digital
Najnowsze instrukcje dla Bezprzewodowy system audio
28 Września 2024
27 Września 2024
27 Września 2024
26 Września 2024
26 Września 2024
26 Września 2024
23 Września 2024
23 Września 2024
22 Września 2024
9 Września 2024