Instrukcja obsługi Allen & Heath ZEDi-10FX


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Allen & Heath ZEDi-10FX (12 stron) w kategorii Konsola miksująca. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/12
ZEDi 10 / ZEDi 10FX - -
10 Channel Live + Recording Mixer User Guide
Thank you for purchasing this Allen & Heath ZEDi 10 or ZEDi 10FX!- -
We recommend that you read all of this user guide to get the best from your mixer and after
reading, please keep this safe for future reference.
Included in this package is:
ZEDi 10 / ZEDi 10FX Mixer.- -
IEC C5 Mains Power Cable. Please check correct mains plug is fitted for your country.
USB A B Cable 2M.-
This User Guide!
2
1. Get to know your mixer
1.1 MONO INPUT CHANNELS (M)
1. Mic Input Socket uses a standard 3 Pin XLR socket for connecting -
dynamic or condenser microphones.
2. Line / Inst Input Socket uses a standard 1/4” (6.25mm) Jack socket
for connecting balanced or unbalanced signals such as guitars and
other instruments.
3. Gain Control adjusts the gain of the input preamplifier to drive the
source signal level. Gain ranges from 5dB to 60dB.
4. Instrument Line / Inst input activates the circuit for electro-
acoustic and electric guitars, basses and other Direct Input
instruments. When activated the Mic Input Socket is disabled.
5. For channels M3 M4 and this is replaced by a LINE/PAD switch. This
activates the LINE input and a PAD Mic Input circuit which reduces the
Socket gain level by 20dB for very loud sources.-
6. lo-cut (Hi Pass Filter) is used for reducing Low Frequency noise such -
as handling noise, popping, rumble and proximity effect in microphone
signals.
7. HF EQ (High Frequency) equaliser affects treble frequencies in
the signal for adding “brightness” and “definition” or for reducing “hiss”
and “harshness”.
8. MF EQ (Mid Frequenc y) equaliser aff ects frequencies in the signal
for adding “presence” or for removing “boxiness”.
9. LF EQ (Low Frequency) equaliser affects bass frequenc ies in the
signal to cover “boom” and “sub bass” frequencies.-
10. AUX send controls the amount of si gnal sent from the channel to
the aux buss and AUX OUT MIX. The signal is sourced pre fader (-) so
is independent of the level being sent to the main L R Mix. -
There is a master level control for the .AUX OUT
11. FX send controls the amount of signal sent from the channel to
the FX buss and the . The signal is post fader ( ) which FX OUT -MIX
means it’s affected by the channel control so it stays in proportion MIX
to the signal going to the .MAIN MIX
There is no master level control for the .FX OUT
12. PAN adjusts signal from a mono input channel between the left
and right busses and subsequently the main outputs.
13. MIX rotary fader controls the amount of signal to the left and right
busses.
14. -Pre Fade Listen (PFL) switches the channel input signal to the
headphones for checking before adding it to Mix. The PFL signal is
taken after the but before the control. The EQ MIX LR Meters display
the channel input level when the PFL switch is activated.
3
1.2 STEREO INPUT CHANNELS (ST)
1. ST1 ST2 Inputsand use standard 1/4” (6.25mm) Jack
sockets for balanced or unbalanced line level stereo sources
such as professional keyboards, drum machines and other pro
audio equipment.
2. 2 -ST2 USB IN 1 includes from the ZEDi USB interface.
Plugging into the jacks will override the input from USB. Make
sure nothing is plugged into the jack sockets if you want to use
the for USB playback.ST-2
3. 4 -ST3 USB IN 3is from the ZEDi USB interface.
See section 3. for more information on the ZEDi USB
interface.
4. ST1 Gain Control ST1adjusts the input level to the channel.
There is no Gain Control for ST2.
5. HF LF EQ M1 M2 and are the same for as they are for & and
are set at the same frequencies. There is no EQ for .ST2
6. AUX send controls the amount of signal sent from the
channel to the aux buss and AUX OUT.
The signal is sourced pre fader ( ) so is independent of the -MIX
level being sent to the main L R Mix. -Unlike the FX bus, there is
a master level control for the Aux output.
7. FX send controls the amount of signal sent from the
channel to the FX buss and the . The signal is postFX OUT -
fader ( ) which means it’s affected by the channel MIX MIX
control so it stays in proportion to the signal going to the MAIN
MIX.
8. BAL adjusts the relative level between the left and right
stereo signals as they are sent to the left and right busses and
subsequently the main outputs. There is no BAL for .ST2
9. MIX rotary fader controls the amount of signal to the left
and right busses.
10. -Pre Fade Listen (PFL) switches the channel input signal to
the headphones for checking before adding it to Mix. The PFL
signal is taken after the but before the control. EQ MIX
The LR Meters PFL display the channel input level when is
activated.


Specyfikacje produktu

Marka: Allen & Heath
Kategoria: Konsola miksująca
Model: ZEDi-10FX

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Allen & Heath ZEDi-10FX, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Konsola miksująca Allen & Heath

Instrukcje Konsola miksująca

Najnowsze instrukcje dla Konsola miksująca

Behringer

Behringer XENYX QX2442USB Instrukcja

14 Października 2024
Koenic

Koenic KHB 800 Instrukcja

14 Października 2024
Ibiza Sound

Ibiza Sound MX801 Instrukcja

14 Października 2024
Pyle Pro

Pyle Pro PMXU83BT Instrukcja

12 Października 2024
Vonyx

Vonyx VMA106 Instrukcja

9 Października 2024
Røde

Røde RØDECaster Duo Instrukcja

8 Października 2024
Valcom

Valcom V-9985 Instrukcja

8 Października 2024
Valcom

Valcom V-9983 Instrukcja

8 Października 2024
Valcom

Valcom V-9984 Instrukcja

8 Października 2024
Glemm

Glemm MX 4816 Instrukcja

8 Października 2024