Instrukcja obsługi AIM Sportline Multichron

AIM Sportline Różnorodny Multichron

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla AIM Sportline Multichron (3 stron) w kategorii Różnorodny. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/3
Release 1.04
Aim s.r.l. Via Cavalcanti 8, 20063 Cernusco sul Naviglio – MI – ITALY
Tel (+39) – 02- 9290571 . Fax (+39) – 02 – 92118024 www.aim-sportline.com
1) Initial set up When you first use the Multichron, press the CONF-SPEED button to set the following options (press the plus or
minus buttons to vary the settings and then press the DATA-STOP button to move to the next line):
i) Contrast (to alter the display and viewing angle)
ii) Light on/off (for versions with backlight)
iii) Beep sound on/off
iv) Send (IRDA) PC transmission data (see PC data section)
v) Econ on/off (Power saver, when “on” the display closes down until a button is pressed.
Press the CONF-SPEED button to move to the next set up screen:
vi) Alarm on/off
vii) Set the time when the alarm will go off (use the DATA-STOP button to choose the hours and minutes to change. Change
the flashing digit by using the plus or minus button.
viii) Chime on/off (when “on” the multichron beeps every 30 minutes)
ix) Time of day: Use the same button logic as in vii) above to set the correct time of day. The default setting is 12 hour mode.
You can change this from A (am) to P (pm) or _ (24 hour mode)
Press the CONF-SPEED button to move to the next set up screen:
x) Distance measurement ( you can choose between Miles or Kilometers
Competitor 2,3 and 4
previous lap/current lap
times
Competitor 1 previous lap
time
Competitor 1 current lap
running time.
Lap number
Number in SPL
column shows the
number of split
times per lap. A b
in this column
denotes best time
Use – set + when configuring your required
settings
For competitor
1,2,3 and 4 timing
IR PC Data Transmission system
Release 1.04
Aim s.r.l. Via Cavalcanti 8, 20063 Cernusco sul Naviglio – MI – ITALY
Tel (+39) – 02- 9290571 . Fax (+39) – 02 – 92118024 www.aim-sportline.com
xi) Length of the Circuit: Enter the distance to be timed (optional)
xii) Stopwatch operating mode: Multi /Single (see operating mode section)
xiii) Stopwatch operating mode: Multi start/One start (see operating mode section)
xiv) Stopwatch operating mode: Timer on/off (see operating mode section)
Press the CONF-SPEED button to move to the next set up screen:
xv) Countdown timer settings: Use the same button logic as in vii) above to set the required countdown time
When the settings are complete, press the MODE button to go to either Stopwatch, Data review, Countdown or Alarm screens.
Stopwatch operating mode
Multichron offers four ways of capturing split/lap times using a combination of two options:
Multi or One start: Choose Multi-start if competitors start at different times. Choose One-start if competitors start at the same time.
Single mode/multi mode:
Single mode allows you to take lap times and or split times by pressing the LAP/STARTand or RESET/SPLIT button to take a
time then allocate the competitor number later (useful when competitors are close together)
Multi mode allows you to take lap times and or split times and is best for timing when competitors are less close together.
There are four operating modes for you to choose from:
Multi Mode, Multi Start = Competitors start at individual times
To take lap times for up to 4 competitors:
Press START/LAP button when competitor 1 begins.
The bottom display shows competitor 1’s current lap running time.
Press button 2 when competitor 2 begins, Press button 3 when competitor 3 begins and Press button 4 when competitor 4 begins.
The current running lap time is shown for each competitor.
Press button 1, 2, 3 and 4 when each competitor completes a lap. A lap time is taken and the next lap starts timing from zero.
Repeat this process until you have the required number of lap times.
The display will show the previous lap number and time for each competitor and the current running lap time for competitor 1.
After a short time, the display for competitors 2,3 and 4 return to current lap running time.
You can also capture up to 9 split times within a lap for each competitor as well as lap times:
To do this, press and hold down the RESET/SPLIT button. When you want to take the split time, press the buttons for the
competitors (button 1 for competitor 1 etc.)
The display will show the lap number, the number of splits within that lap and the last split time. After a short time, the display
returns to current lap running time.
Multi Mode, One Start = Competitors start at the same time
To take lap times for up to 4 Competitors:
Press START/LAP button when competitors start the event
The bottom display shows competitor 1’s current lap running time.
Press button 1,2,3,4 to take competitors 1,2,3 and 4’s lap times
The display will show the previous lap number and time for each competitor and the current running lap time for competitor 1.
After a short time, the display for competitors 2,3 and 4 return to current lap running time.
Repeat this process until you have the required number of lap times.
Note: Pressing the START/LAP button in this mode will only capture lap times for competitor 1.
You can also capture up to 9 split times within a lap for each competitor as well as lap times:
Release 1.04
Aim s.r.l. Via Cavalcanti 8, 20063 Cernusco sul Naviglio – MI – ITALY
Tel (+39) – 02- 9290571 . Fax (+39) – 02 – 92118024 www.aim-sportline.com
To do this, press and hold down the RESET/SPLIT button. When you want to take the split time, press the buttons for the
competitors (button 1 for competitor 1 etc.)
The display will show the lap number, the number of splits within that lap and the last split time.
After a short time, the display returns to current lap running time.
Single Mode, Multi Start = Competitors start at individual times
To take lap times for up to 4 competitors:
Press start/lap button to set up the display (so that the zero’s start to flash) for each competitor.
Press button 1 to see the bottom display which shows competitor 1’s current lap running time.
Press START/LAP to take a lap time and then enter the number of the competitor. The display will show the previous lap
number and lap time for each competitor. After a short time, the display returns to current lap running time
You can also capture up to 9 split times within a lap for each competitor as well as lap times:
During lap timing, press SPLIT/RESET to take a split time. Then enter the button for the
competitor (button 1 for competitor 1 etc.)
The display will show the lap number, the number of splits within that lap and the last split time.
After a short time, the display returns to current lap running time
Single Mode, One Start = Competitors start at the same time.
In this mode, you can see the running lap times for all competitors. Split times show for a few
seconds before returning to current lap running time.
To take lap times for up to 4 competitors:
Press start/lap button to set up the display (so that the zero’s start to flash) for each competitor.
The bottom display shows competitor 1’s current lap running time. Current running times are also shown for competitor 2,3
and 4.
Press START/LAP to take a lap time. All displays will flash. Enter the number of the competitor. The display will show the
previous lap number and lap time for each competitor. After a short time, the display returns to current lap running time
You can also capture up to 9 split times within a lap for each competitor as well as lap times:
To do this, press and hold down the RESET/SPLIT button. When you want to take the split time, press the buttons for the
competitors (button 1 for competitor 1 etc.)
The display will show the lap number, the number of splits within that lap and the last split time.
After a short time, the display returns to current lap running time
Note: A “b” next to the lap time shows that it was the competitors best time to date.
You can review the data in the following ways:
Press the MODE Button. The bottom row displays the word RECALL
Press BEST-AVG Button
The first display shows each competitors fastest lap and lap time
Press (+) Button 4 to review up the lap times and (-) Button 3 to review down the lap and split times.
Press BEST-AVG BUTTON again to see average speed per competitor
Press BEST-AVG BUTTON again to see the total time per competitor.
Data Download
Details of the data download function are included in the software section on our website www.aim-sportline.com.

Specyfikacje produktu

Marka: AIM Sportline
Kategoria: Różnorodny
Model: Multichron

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z AIM Sportline Multichron, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Różnorodny AIM Sportline

AIM Sportline

AIM Sportline SOLO DL Instrukcja

30 Czerwca 2024
AIM Sportline

AIM Sportline MXL Instrukcja

30 Czerwca 2024
AIM Sportline

AIM Sportline Multichron Instrukcja

30 Czerwca 2024

Instrukcje Różnorodny

Najnowsze instrukcje dla Różnorodny

AL-KO

AL-KO AKS 1300 Instrukcja

15 Stycznia 2025
Schavis

Schavis CIRCLE DUO X-LINE Instrukcja

13 Stycznia 2025
Schavis

Schavis INDOOR DUO X-LINE Instrukcja

13 Stycznia 2025
Schavis

Schavis INDOOR DUO Instrukcja

13 Stycznia 2025
ION

ION ICADE CORE Instrukcja

13 Stycznia 2025
ION

ION ICADE Instrukcja

13 Stycznia 2025
Superrollo

Superrollo GW245 Instrukcja

12 Stycznia 2025
Huawei

Huawei X Gentle Monster Eyewear Instrukcja

12 Stycznia 2025
Superrollo

Superrollo GW240 Instrukcja

12 Stycznia 2025
BeamZ

BeamZ 150.460 - Panther 25 Instrukcja

11 Stycznia 2025