Instrukcja obsługi Aeotec Range Extender 7

Aeotec inteligentny dom Range Extender 7

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Aeotec Range Extender 7 (9 stron) w kategorii inteligentny dom. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/9
11-6-2020 Range Extender 7 user guide. : Aeotec Group
https://aeotec.freshdesk.com/support/solutions/articles/6000226827-range-extender-7-user-guide- 1/4
Range Extender 7 user guide.
Modified on: Mon, 16 Mar, 2020 at 2:06 AM
Aeotec Range Extender 7.
Aeotec Range Extender 7 was developed to amplify Z-Wave signals. It isZ-Wave Plus (http://aeotec.com/z-wave-plus)
powered by Aeotec’s technology. You can find outGen7 (https://aeotec.com/z-wave-home-automation/z-wave-gen7.html)
more about 7 by following that link.Range Extender (http://aeotec.com/z-wave-repeater)
To see whether Range Extender 7 is known to be compatible with your Z-Wave system or not, please reference our Z-
Wave gateway comparison (http://aeotec.com/z-wave-gateways) listing. The technical specifications of Range
Extender 7 (https://aeotec.freshdesk.com/a/solutions/articles/6000226828) can be viewed at that link.
Important safety information.
Please read this and other device guides carefully. Failure to follow the recommendations set forth by Aeotec Limited
may be dangerous or cause a violation of the law. The manufacturer, importer, distributor, and/or reseller will not be
held responsible for any loss or damage resulting from not following any instructions in this guide or in other materials.
Keep product away from open flames and extreme heat. Avoid direct sunlight or heat exposure.
Range Extender 7 is intended for indoor use in dry locations only. Do not use in damp, moist, and/or wet locations.
11-6-2020 Range Extender 7 user guide. : Aeotec Group
https://aeotec.freshdesk.com/support/solutions/articles/6000226827-range-extender-7-user-guide- 2/4
Quick start.
Adding your Range Extender into a Z-Wave network.
Getting your Range Extender up and running is as simple as plugging it into a wall outlet and adding it to your Z-Wave
network. There are 2 methods to pairing your Range Extender depending on the capabilities of your Z-Wave
gateway/controller/hub.
SmartStart Inclusion.
You can use this method of inclusion only if your Z-Wave gateway/controller/hub supports SmartStart.
1. Open up your Z-Wave gateway/controller/app.
2. Select SmartStart inclusion.
3. Scan the QR code located on the Range Extender 7.
4. Within 10 minutes after powering your Range Extender 7, it will automatically get included into your Z-Wave
gateway/controller/hub.
LED will flash for 1 second after Repeater is powered, if successful, the LED will become a solid bright light for 2
seconds.
Classic Inclusion.
1. Decide on where you want your Range Extender to be placed and then plug it into a wall outlet.
Make sure that the LED is breathing its white LED.
2. Set your Z-Wave Controller into pairing mode.
3. Press the Z-Wave Button on your Range Extender and quickly release the button (should only be a quick tap
action on the button).
Range Extender 7 will quickly flash its white LED up to 30 seconds or until it is paired successfully. If successfully
paired, the LEDs light will become brighter.
If your repeater failed to pair, the LED will return to slow breathing LED. If it is this case, please return to step 2.
11-6-2020 Range Extender 7 user guide. : Aeotec Group
https://aeotec.freshdesk.com/support/solutions/articles/6000226827-range-extender-7-user-guide- 3/4
4. If you pairing with S2 encryption/security, enter the first 5 digits of the DSK into your controller/gateway/hub
interface when requested.
The DSK is printed on the Range Extender 7 itself located right under the QR code.
General LED Status
There are a few LED indications that you will need to pay attention to for the Range Extender 7.
Unpaired from network.
Slow breathing white LED
While paired to an existing network.
The LED state is configurable, there are 2 states that you can choose, the LED will remain in a solid state as off or
on:
LED on.
LED off.
Advanced Functions.
Removing your Range Extender from a Z-Wave network.
Your Range Extender can be removed from your Z-Wave network at any time. You’ll need to use your Z-Wave
network’s main controller. To set your Z-Wave controller/gateway into removal mode, please refer to the respective
section within your controller instruction manual.
1. Set your Z-Wave Controller into device removal mode.
2. Press the Z-Wave Button on your Range Extender.
3. If Range Extender has been successfully removed from your network, its LED will return to a slow breathing
light.
Control LED of Range Extender 7.
You can turn the LED on or off by using the action button of your Range Extender 7:
Tap the Action Button 2x times.
LED should turn on or off each time you do so.


Specyfikacje produktu

Marka: Aeotec
Kategoria: inteligentny dom
Model: Range Extender 7

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Aeotec Range Extender 7, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje inteligentny dom Aeotec

Instrukcje inteligentny dom

Najnowsze instrukcje dla inteligentny dom

Elro

Elro AB600S-2 Instrukcja

13 Października 2024
EZVIZ

EZVIZ DL01 Pro Instrukcja

9 Października 2024
Tenda

Tenda SP15 Instrukcja

9 Października 2024
Ikea

Ikea RODRET 005.597.95 Instrukcja

8 Października 2024
Acer

Acer Wave 7 Instrukcja

8 Października 2024
Ikea

Ikea TRETAKT 505.565.20 Instrukcja

8 Października 2024
Ikea

Ikea RODRET 505.597.93 Instrukcja

8 Października 2024
V-TAC

V-TAC VT-5132 Instrukcja

7 Października 2024