Instrukcja obsługi Yamaha MG06

Yamaha Konsola miksująca MG06

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Yamaha MG06 (2 stron) w kategorii Konsola miksująca. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

Welcome

Thank you for purchasing the Yamaha MG06X/MG06 Mixing Console.

Please read this manual thoroughly to get the most out of the product and ensure long-term,

trouble-free use. After reading this manual, keep it readily available for future reference.

* For the remainder of this manual, the word “mixer” is used instead of “Mixing Console.”

** In this manual, all panel illustrations show the MG06X panel.

Main Features

• 6-channel mixer features microphone inputs and stereo/mono line inputs for input jacks.

• Yamaha’s premium head amp “D-PRE” for providing high quality sound.

• PAD switch to support a wide variety of inputs to the channels 1/L and 2/R.

• (MG06X) Yamaha’s high-quality SPX effects (6 types), providing optimum processing for

instruments or vocals.

Included Accessories

• AC power adaptor

• Technical Speciﬁcations: Includes block diagram, dimensions, general speciﬁcations, and

input/output characteristics.

• Owner’s Manual (this leaﬂet)

Quick Start Guide

STEP 1 Connecting speakers, microphones, and

instruments, etc.

Connection Example

Microphones

Electric acoustic guitar

Electric keyboard

Powered speakers

Headphones

Portable

audio

player

L* RRL R* L

RRL L

* Stereo mini plugs require conversion plugs to phone plugs.

STEP 2 Getting Sound to the Speakers

1 Make sure that all switches including the [ ] switch are not pressed ( ).N

2 Connect the supplied AC power adaptor.

First connect the adaptor to the DC IN [12V] jack at the back panel of the unit (

1),

and then to the outlet (2).

Power adaptor

To electrical outlet

3 Turn the [GAIN], [LEVEL] knobs (white), and [STEREO LEVEL] knob (red)

fully to the left (minimum). Set the equalizer knobs (green) to the center “6”

position.

Refer to the illustration (at the top of the next column, before step 4).

Equalizer

LEVEL

GAIN

STEREO LEVEL

4 If you connect a device with high output level, such as a CD player or an

electric keyboard to the channels 1/L and 2/R, turn on ( ) the [PAD] switch O

of the corresponding channel*.

* Channel: Location or path where sound is input.

Channel 1/L

Channel number

Channel 2/R

PAD

NOTE If you are using condenser microphones, turn on ( ) the [PHANTOM +48V] switch. O

5 Turn on the power to connected devices in the following order:

(microphone), (instrument), (audio device)

[ ] (switch on unit) (speakers)

NOTICE

Follow this order to avoid any loud, unexpected noise from the speakers. Reverse the order when

turning the power off.

6 Set the [STEREO LEVEL] knob to the “3” position.

7 For channels to which a microphone is connected, set the [GAIN] knob to

roughly the 12 o’clock position.

8 While playing your instrument or speaking into the microphone, turn the

[LEVEL] knob to adjust the volume of the corresponding channel.

9 If necessary, adjust the volume of the speaker or power amp.

If you hear the sound and the volume seems appropriate, setup is complete. If not,

please go to step 10 below.

NOTICE

To avoid any loud noise from the speaker, ﬁrst turn off the power of the speaker (speaker amp), then

the unit itself, and ﬁnally the connected sound source such as an instrument.

10 If the sound is not heard, or if you want to adjust the volume, follow the

instructions in the boxed section below.

If you still do not hear the sound after doing the following steps, please refer to the

checklist in the “Troubleshooting” section at the back of this booklet.

ZT44280

MIXING CONSOLE

Owner’s Manual

< There is no sound, or you need to increase the volume

1 Turn the [GAIN] knob to the right so that the corre-

sponding [PEAK] LED flashes briefly.

NOTE If the [PEAK] LED does not light even if the [GAIN] knob has been

turned fully to the right, raise the volume of the sound source

(instrument, etc.).

If no sound is heard or the volume does not increase after step 1:

2 If the [PAD] switch is turned on ( ), set the [LEVEL] O

knob to “0” (minimum), and then turn off ( ) the N

switch.

3 Slowly turn the [LEVEL] knob to the right until the

desired volume is reached.

< To decrease the volume:

1 Set the [LEVEL] knob to “0” (minimum), then turn on

( ) the [PAD] switch.O

2 Slowly turn the [LEVEL] knob to the right until the

desired volume is reached.

If the volume does not decrease after the above steps:

3 Lower the volume of the instrument or audio device.

PAD

GAIN

LEVEL

PEAK

Controls and Functions

)

# $ % B

(

2 [MIC/LINE] mono input jacks (channels 1/L, 2/R)

Connect a microphone, an instrument, or an audio device (CD

player, etc.) to the unit. These jacks support both XLR and

phone plugs.

XLR Phone

3 [LINE] stereo input jacks (channels 3/4, 5/6)

Connect line-level devices such as an electric keyboard or

an audio device. These jacks support phone plugs. If you use

only the [L/MONO] jack, same sound is output from both L (left)

and R (right) speakers.

4[PAD] switches

Turning the switch on ( ) will attenuate the sound input to the O

unit. If you hear distortion or the [PEAK] LED lights, turn the @

switch on ( ).O

NOTE Turn the [LEVEL] knob to "0" (minimum) before toggling

the [PAD] switch on ( ) and off ( ). Otherwise, noise O N

may be produced.

5 [HPF] (High-Pass Filter) switches

Turning the switch on ( ) will apply a high-pass ﬁlter that O

attenuates frequencies below 80Hz. When speaking into the

microphone, you may want to turn this switch on ( ), in order O

to reduce unwanted vibration and wind sound received by the

microphone.

@ [PEAK] LED

Lights when the volume of input and/or post-equalizer sound

is too high. If it is lit, turn the [GAIN] knob to the left to lower 8

the volume.

# [LEVEL] knobs

For adjusting the volume balance among the channels.

$ [PHONES LEVEL] knob

Adjusts the headphones volume.

% [STEREO LEVEL] knob

Adjusts the overall volume output from the [STEREO OUT]

output jacks.

1 (Back panel) DC IN [12V] jack

Connect the supplied AC power adaptor to this jack.

6 [STEREO OUT] output jacks

Connect a powered speaker or powered amp. These jacks

support both XLR and phone plugs.

7 [PHONES] output jack

Connect a set of headphones. This jack supports a stereo

phone plug.

^ [PHANTOM +48V] switch/LED

When this switch is on ( ), the LED lights indicating that the O

unit supplies DC+48V phantom power to the XLR plugs of

the [MIC/LINE] mono input jacks . Turn this switch on when 2

using a phantom-powered condenser microphone.

CAUTION

Be sure to leave this switch off ( ) if you do not need phantom power.N

Follow the important precautions below, in order to prevent noise and

possible damage to external devices as well as the unit when you

operate this switch.

• Be sure to leave this switch off when you connect a device that does

not support phantom power to channels 1/L or 2/R.

• Do not connect/disconnect a cable to/from channels 1/L and 2/R

while this switch is on.

• Turn the [LEVEL] knob of the channels 1/L and 2/R to the minimum

before operating this switch.

& [ ] (On/Standby) switch

Toggles to turn the unit’s power On ( ) or Standby ( ).O N

CAUTION

• Rapidly switching the unit between on and standby in succession

can cause it to malfunction. After setting the unit to standby, wait for

about 5 seconds before turning it on again.

• Even when the switch is in the standby ( ) position, electricity is still N

ﬂowing to the unit. If you do not plan to use the unit for a while, be

sure to unplug the AC power adaptor from the outlet.

* [REVERB / DELAY] switch (MG06X)N O

Toggles to select the effect applied to channels 1/L and 2/R

between Reverb ( ) and Delay ( ).N O

( Effect select slide switch (MG06X)

Moves up and down to select the effect type. The LED of the

selected effect lights.

A [FX RTN LEVEL] (effect return level) knob

(MG06X)

Adjusts the volume of the effect sound.

B Level meter

The L and R meters show the level of the signal output from

the [STEREO OUT] jack. If the [PEAK] lamp lights in red, use

the [LEVEL] knob to lower the volume.

8 [GAIN] knobs

Determines the basic volume for each channel, 1/L and 2/R.

Adjust these so that the corresponding [PEAK] LEDs ﬂash @

brieﬂy when singing or playing the loudest.

9 Equalizer (EQ) knobs

Adjust the sound quality by using the [HIGH] (high frequency

band) and [LOW] (low frequency band) knobs. If you do not

need to adjust the sound quality, set the knob to the “6” (ﬂat)

position.

) [FX] switches (MG06X)

Toggle the FX (effect) of channels 1/L and/or 2/R on and off.

! [ MONO/ STEREO] switchN O

( ) [MONO]: Sound input to channels 1/L or 2/R can be N

heard from both the right and left speakers. If you use the 1/L

or 2/R individually, set the switch to this setting.

( ) [STEREO]: Sound input to channel 1/L can be heard from O

only the left speaker, and that input to channel 2/R can be

heard from only the right speaker.

Applying Effects (MG06X)

The MG06X features built-in effects (Reverb and Delay) processors that are in the same

league as our famed SPX effect processor series. Those effects let you simulate the

acoustics of different performance environments, such as concert halls and small clubs,

and add warm, natural ambience to your vocals or instrument performance.

1 Use the [REVERB / DELAY] switch to select Reverb ( ) or Delay ( ).N O N O

Type Description

REVERB HALL Reverb simulating a large space such as a concert hall.

ROOM Reverb simulating the acoustics of a small space (room).

PLATE Reverb simulating a metal-plate, producing a more hard-edged sound.

DELAY SHORT Short echo with a “doubled” sound.

LONG Long, resonant echo with an extended decay.

VO.ECHO Echo suitable for vocals.

2 Move the effect select slide switch up and down to select the effect type.

The LED of the selected effect lights.

3 Turn on ( ) the [FX] switch of the channel (1/L or 2/R) to which you want to O

apply the effect.

4 Turn the [FX RTN LEVEL] knob to adjust the effect amount.

Mixer Basics:

Where Your Sound Goes

The right illustration diagram illustrates the sound

ﬂow from summing (mixing) sound which was

input to the channels to outputting sound from

the speakers or headphones. Let’s ﬁnd out where

input sound goes once it’s inside the mixer.

1 Input the sound from a microphone or

instrument

5 Output the sound from speakers or

headphones

4 Final adjustment of the volume of the

mixed sound

The signal ow of the sound rightward, from

the channels to the nal output.

2 Adjust the sound quality and volume of each

channel

Equalizer (HIGH, LOW) knobs

GAIN, LEVEL Knobs

Specyfikacje produktu

Marka:	Yamaha
Kategoria:	Konsola miksująca
Model:	MG06

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Yamaha MG06, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Konsola miksująca Yamaha

Yamaha MG166C-USB Instrukcja

31 Grudnia 2025

Yamaha SP02R96 Instrukcja

31 Grudnia 2025

Yamaha DCU5D Instrukcja

31 Grudnia 2025

Yamaha IM8-40 Instrukcja

31 Grudnia 2025

Yamaha IM8-32 Instrukcja

31 Grudnia 2025

Yamaha MB02R96 Instrukcja

15 Grudnia 2024

Yamaha RSio64-D Instrukcja

14 Grudnia 2024

Yamaha Ri8-D Instrukcja

14 Grudnia 2024

Yamaha Rio1608-D Instrukcja

14 Grudnia 2024

Yamaha ZG01 Instrukcja

29 Września 2024

Instrukcje Konsola miksująca

Najnowsze instrukcje dla Konsola miksująca

American Audio Q-D6 Instrukcja

15 Stycznia 2025

ADB ME1163 Instrukcja

15 Stycznia 2025

Samson L1200 Instrukcja

14 Stycznia 2025

Samson MDR624 Instrukcja

14 Stycznia 2025

Konig KN-DIGICON20 Instrukcja

11 Stycznia 2025

Vonyx STM500BT Instrukcja

11 Stycznia 2025

Rane Sixty-Four Instrukcja

11 Stycznia 2025

Wharfedale SL 1224 USB Instrukcja

11 Stycznia 2025

Glemm MXD 08 Instrukcja

10 Stycznia 2025

Alfatron ALF-VMix41 Instrukcja

8 Stycznia 2025