Instrukcja obsługi Whirlpool YWMH53521HW

Whirlpool Magnetostrykcja YWMH53521HW

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Whirlpool YWMH53521HW (32 stron) w kategorii Magnetostrykcja. Ta instrukcja była pomocna dla 14 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/32

MICROWAVE HOOD COMBINATION

INSTALLATION INSTRUCTIONS

This product is suitable for use above electric or gas cooking products up to and including 36" (91.4 cm) wide. See the “Installation

Requirements” section for further notes.

These installation instructions cover different models. The appearance of your particular model may differ slightly from the illustration

in these installation instructions.

INSTRUCTIONS D’INSTALLATION

DE L’ENSEMBLE FOUR À MICRO-ONDES/HOTTE

Ce produit est conçu pour l’utilisation au-dessus d’appareils de cuisson électriques ou à gaz de 36 po (91,4 cm) de largeur ou moins.

Voir la section « Exigences d’installation » pour d’autres remarques.

Ces instructions d’installation sont valables pour plusieurs modèles. Il se peut que l’apparence de votre propre modèle soit légèrement

différente de celle montrée sur les illustrations dans ce document.

Table of Contents/Table des matières

W11496339A

MICROWAVE HOOD COMBINATION SAFETY ............................2

INSTALLATION REQUIREMENTS .................................................2

Tools and Parts .............................................................................2

Separate Cardboard Template .....................................................3

Location Requirements ................................................................3

Product Dimensions .....................................................................3

Electrical Requirements ...............................................................4

INSTALLATION INSTRUCTIONS ...................................................5

Remove Mounting Plate ...............................................................5

Rotate Blower Motor ....................................................................5

Locate Wall Stud(s) ......................................................................8

Mark Rear Wall .............................................................................9

Drill Holes in Rear Wall ...............................................................10

Attach Mounting Plate to Wall ...................................................10

Prepare Upper Cabinet ..............................................................11

Install Damper Assembly

(for wall venting only) ..................................................................11

Install the Microwave Oven ........................................................12

Complete Installation .................................................................13

VENTING DESIGN SPECIFICATIONS ........................................14

ASSISTANCE ................................................................................15

Replacement Parts .....................................................................15

Accessories ................................................................................15

SÉCURITÉ DE L’ENSEMBLE FOUR À

MICRO-ONDES/HOTTE...............................................................16

EXIGENCES D’INSTALLATION ...................................................16

Outillage et pièces ......................................................................16

Gabarit en carton séparé ...........................................................17

Exigences d’emplacement .........................................................17

Dimensions du produit ...............................................................18

Spéci cations électriques ..........................................................18

INSTRUCTIONS D’INSTALLATION .............................................19

Dépose de la plaque de montage ..............................................19

Réorientation du moteur du ventilateur .....................................19

Identi er la position du/des poteau(x) du colombage mural .....22

Tracé sur le mur arrière ..............................................................23

Perçage de trous dans le mur arrière .........................................24

Fixation de la plaque de montage sur le mur ............................24

Préparation du placard supérieur ..............................................25

Installation du module du clapet anti-re ux

(pour décharge à travers le mur uniquement) ............................25

Installation du four à micro-ondes .............................................26

Achever l’installation ..................................................................28

SPÉCIFICATIONS/CONCEPTION DU CIRCUIT

D’ÉVACUATION ...........................................................................28

ASSISTANCE ................................................................................30

Pièces de rechange ....................................................................30

Accessoires ................................................................................30

MICROWAVE HOOD COMBINATION SAFETY

INSTALLATION REQUIREMENTS

Tools and Parts

Tools Needed

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

■Measuring tape

■Pencil

■Masking tape or thumbtacks

■Scissors

■No. 2 Phillips screwdriver

■No. 3 Phillips screwdriver

for 1/4-20 x 3" (7.6 cm) bolts

■Drill

■3/16" (5 mm), 3/8" (1cm),

5/8" (1.6 cm) drill bits

■3/4" (1.9 cm) hole saw

■Diagonal wire cutting pliers

■Stud  nder

■7⁄16" (1.1 cm) socket wrench (or box wrench) for 1/4" x 2"

(6.4 mm x 5.1cm) lag screws

■11/2" (3.8 cm) diameter hole drill bit for wood or metal cabinet

■Keyhole saw

■Caulking gun and weatherproof caulking compound

■Duct tape

Parts Needed

For information on reordering, see the “Replacement Parts”

section.

NOTE: The hardware items listed here are for wood studs.

For other types of wall structures, be sure to use appropriate

fasteners.

NOTE: Depending on model, aluminum grease  lter and

charcoal  lter may be combined.

Materials Needed

Standard  ttings for wall or roof venting. See the “Venting Design

Speci cations” section.

A B C D E F G

A. 3/16-24 x 3" round-head

bolts (2)

B. 1/4-20 x 3"  at-head bolts (2)

C. Washers (2)

D. 3/16" toggle nuts (2)

E. 1/4" x 2" lag screws (2)

F. #6 x 3/8" Sheet metal screws (2)

G. Power supply cord bushing (1)

H. Damper assembly (for wall or

roof venting)

Not Shown:

■Mounting plate (attached to

back of microwave oven)

■Cardboard template (part of

packaging)

■Aluminum grease  lters

■Charcoal  lters (Depending

on model, charcoal  lters may

not be included. See User

Instructions.)

Separate Cardboard Template

The wall template and upper cabinet template is embedded in

the backside of the carton box. They are used as a rear wall

template and upper cabinet template.

1. Cut along the dotted line to separate the cardboard template

from the backside of the carton box.

2. Set the cardboard template to the side and refer to it during

the “Mark Rear Wall” and “Prepare Upper Cabinet” parts of

installation.

Location Requirements

Check the opening where the microwave oven will be installed.

The location must provide:

■Minimum installation dimensions. See the “Installation

Dimensions” illustration.

■Minimum one 2" x 4" (5.1 x 10.2 cm) wood wall stud and

minimum 3/8" (1 cm) thickness drywall or plaster/lath within

cabinet opening.

■Support for weight of 150 lbs (68 kg) which includes

microwave oven and items placed inside the microwave

oven and upper cabinet.

■Grounded electrical outlet inside upper cabinet. See the

“Electrical Requirements” section.

NOTES:

■If installing the microwave oven near a left sidewall, make

sure there is at least 6" (15.2 cm) of clearance between the

wall and the microwave oven so that the door can open fully.

■Some models have a pocket handle. If installing the

microwave near a right side wall, make sure there is at least

3" (7.6 cm) of clearance between wall and microwave oven

so you can grab the handle integrated inside the door.

■Some cabinet and building materials are not designed to

withstand the heat produced by the microwave oven for

cooking. Check with your builder or cabinet supplier to make

sure that the materials used will not discolor, delaminate, or

sustain other damages.

Special Requirements

For Wall Venting Installation Only:

■Cutout must be free of any obstructions so that the vent  t

properly and the damper blade opens freely and fully.

For Roof Venting Installation Only:

■If you are using a rectangular-to-round transition piece, the

3" (7.6 cm) clearance needs to exist above the microwave

oven so that the damper blade can open freely and fully.

See “Rectangular to Round Transition” illustration in the

“Venting Design Speci cations” section.

Installation Dimensions

NOTE: The grounded 3 prong outlet must be inside the upper

cabinet. See the “Electrical Requirements” section.

*30" (76.2 cm) is typical for 66" (167.6 cm) installation height.

Exact dimensions may vary depending on type of range/cooktop

below.

NOTE: To ensure good performance, do not obstruct top vent

air ow. If cabinets are deeper than 14" (35.6 cm) but no more

than 15" (38.1 cm), use the bump out mounting kit replacing the

I bar mounting plate from the wall. The bump out mounting kit

(part # W11185746) is not provided but can be purchased from

Whirlpool.

Product Dimensions

*Overall depth of product will vary slightly depending on door

design.

A. 2" x 4" (5.1 x 10.2 cm) wall stud

B. Grounded 3 prong outlet

12" (30.5 cm) minimum

14" (35.6 cm) maximum

30"

(76.2 cm)

minimum

A B

upper cabinet and

side cabinet depth

30"

(76.2 cm)

typical*

66" (167.6 cm) minimum

I bar mounting plate

Bump out mounting bracket

12" DEEPER 14" 14" DEEPER 15"

¹⁄₄

(41.3 cm)

¹⁄₈

(43.5 cm)

+/-

3/16

(0.5 cm)

17"

Up to

(43.2 cm)*

cm)

⁷⁄₈

" (76.0

A. Backside of the carton box

B. Cardboard template (including Rear Wall template and Upper

Cabinet template)

Specyfikacje produktu

Marka:	Whirlpool
Kategoria:	Magnetostrykcja
Model:	YWMH53521HW

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Whirlpool YWMH53521HW, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Magnetostrykcja Whirlpool

Whirlpool AMW 594 IX Instrukcja

15 Stycznia 2025

Whirlpool AVM 687 IX RVS Instrukcja

15 Stycznia 2025

Whirlpool AMW 525 IX Instrukcja

15 Stycznia 2025

Whirlpool avm 683 ix Instrukcja

15 Stycznia 2025

Whirlpool amw 461 1 ix al nb w Instrukcja

15 Stycznia 2025

Whirlpool AMW 500 Instrukcja

15 Stycznia 2025

Whirlpool AMW 737 WH Instrukcja

15 Stycznia 2025

Whirlpool avm 218 Instrukcja

14 Stycznia 2025

Whirlpool MWD 240 Instrukcja

10 Stycznia 2025

Whirlpool WMCS7022RB Instrukcja

10 Stycznia 2025

Instrukcje Magnetostrykcja

Najnowsze instrukcje dla Magnetostrykcja

ACP JET19 Instrukcja

15 Stycznia 2025

Medion MD 10482 Instrukcja

15 Stycznia 2025

Candy CMG 9523 DB Instrukcja

15 Stycznia 2025

Atag mc 111 f Instrukcja

15 Stycznia 2025

Samsung MG11H2020CT Instrukcja

15 Stycznia 2025

Daewoo KOR 63 MDC Instrukcja

15 Stycznia 2025

Siemens HF 85961 Instrukcja

15 Stycznia 2025

Daewoo KOR9GQR Instrukcja

15 Stycznia 2025

Candy CMG 20D Instrukcja

15 Stycznia 2025

Atag MX 4192 A Instrukcja

15 Stycznia 2025