Instrukcja obsługi Whirlpool WMH76719CB

Whirlpool Magnetostrykcja WMH76719CB

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Whirlpool WMH76719CB (12 stron) w kategorii Magnetostrykcja. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/12
MICROWAVE HOOD COMBINATION
INSTALLATION INSTRUCTIONS
MICROWAVE HOOD COMBINATION SAFETY
This product is suitable for use above electric or gas cooking products up to and including 36" (91.4 cm) wide. See “Installation
Requirements” section for further notes.
These installation instructions cover different models. The appearance of your particular model may differ slightly from the illustration in
these installation instructions.
Table of Contents
MICROWAVE HOOD COMBINATION SAFETY ..............................1
INSTALLATION REQUIREMENTS ...................................................2
Tools and Parts...............................................................................2
Remove Cardboard Template ........................................................2
Location Requirements...................................................................2
Product Dimensions .......................................................................3
Electrical Requirements..................................................................3
INSTALLATION INSTRUCTIONS .....................................................4
Remove Mounting Plate .................................................................4
Rotate Blower Motor.......................................................................4
Locate Wall Stud(s).........................................................................6
Mark Rear Wall................................................................................7
Drill Holes in Rear Wall....................................................................7
Attach Mounting Plate to Wall........................................................8
Prepare Upper Cabinet...................................................................8
Install Damper Assembly ................................................................9
Install the Microwave Oven ............................................................9
Complete Installation ....................................................................10
VENTING DESIGN SPECIFICATIONS............................................11
ASSISTANCE ...................................................................................12
Replacement Parts .......................................................................12
Accessories...................................................................................12
W10247296B
You can be killed or seriously injured if you don't immediately
You can be killed or seriously injured if you don't follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING
INSTALLATION REQUIREMENTS
Tools and Parts
Tools Needed
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools
listed here.
Parts Supplied
For reorder information, see “Replacement Parts” section.
NOTE: The hardware items listed here are for wood studs. For
other types of wall structures, be sure to use appropriate
fasteners.
NOTE: Depending on model, aluminum grease filter and charcoal
filter may be combined.
Materials needed
■Standard fittings for wall or roof venting. See “Venting Design
Specifications” section.
Remove Cardboard Template
The cardboard piece from the top of the microwave oven
packaging is perforated. The piece inside the perforation is for use
as a rear wall template.
1. Cut along the perforation to separate the template from the
rest of the cardboard packaging.
2. Set the cardboard template to the side and refer to it during
the “Mark Rear Wall” part of installation.
Location Requirements
Check the opening where the microwave oven will be installed.
The location must provide:
■Minimum installation dimensions. See “Installation
Dimensions” illustration.
■Minimum one 2" x 4" (50.8 x 101.6 mm) wood wall stud and
minimum 3/8" (10 mm) thickness drywall or plaster/lath within
cabinet opening.
■Support for weight of 150 lbs (68 kg), which includes
microwave oven and items placed inside the microwave oven
and upper cabinet.
■Grounded electrical outlet inside upper cabinet. See
“Electrical Requirements” section.
NOTES:
■If installing the microwave oven near a left sidewall, make sure
there is at least 6" (15.2 cm) of clearance between the wall and
the microwave oven, so that the door can open fully.
■Some cabinet and building materials are not designed to
withstand the heat produced by the microwave oven for
cooking. Check with your builder or cabinet supplier to make
sure that the materials used will not discolor, delaminate or
sustain other damages.
Special Requirements
For Wall Venting Installation Only:
■Cutout must be free of any obstructions so that the vent fits
properly, and the damper blade opens freely and fully.
For Roof Venting Installation Only:
■If you are using a rectangular to round transition piece, the
3" (7.6 cm) clearance needs to exist above the microwave
oven so that the damper blade can open freely and fully. See
“Rectangular to Round Transition” illustration in “Venting
Design Specifications” section.
■Measuring tape
■Pencil
■Masking tape or thumbtacks
■Scissors
■No. 2 Phillips screwdriver
■No. 3 Phillips screwdriver for
1/4-20 x 3" bolts
■Drill
■3/16" (5 mm), 3/8" (10 mm)
drill bits
■3/4" (19 mm) hole saw
■Stud finder
■7/16" socket wrench
(or box wrench) for 1/4" x 2"
lag screws
■1½" (3.8 cm) diam. hole drill
bit for wood or metal
cabinet
■Keyhole saw
■Caulking gun and
weatherproof caulking
compound
■Duct tape
A. 1/4-20 x 3" round-head bolts (2)
B. 1/4-20 x 3" flat-head bolts (2)
C. Washers (2)
D. Toggle nuts (2)
E. 1/4" x 2" lag screws (2)
F. Sheet metal screws (2)
G. Power supply cord bushing (1)
H. Damper assembly (for wall or roof
venting)
Not Shown:
Upper cabinet template
Mounting plate (attached to
back of microwave oven)
Cardboard template (part of
packaging)
Aluminum grease filters
Charcoal filters (Depending
on model, charcoal filters
may not be included. See
User Instructions.)
A B C D E F G
H
Installation Dimensions
NOTE: The grounded 3 prong outlet must be inside the upper
cabinet. See “Electrical Requirements” section.
*30" (76.2 cm) is typical for 66" (167.6 cm) installation height.
Exact dimensions may vary depending on type of range/cooktop
below.
Product Dimensions
Electrical Requirements
Observe all governing codes and ordinances.
Required:
■A 120 Volt, 60 Hz, AC only, 15- or 20-amp electrical supply
with a fuse or circuit breaker.
Recommended:
■A time-delay fuse or time-delay circuit breaker.
■A separate circuit serving only this microwave oven.
A. 2" x 4" wall stud
B. Grounded 3 prong outlet
12" (30.5 cm) min.
14" (35.6 cm) max.
30"
(76.2 cm)
min.
A B
upper cabinet and
side cabinet depth
30"
(76.2 cm)
typical*
66" (167.6 cm) min.
29⁷⁄₈" (76.0 cm)
15
³⁄₄
"
(40.0 cm)
17¹⁄₄"
(43.8 cm)
16¹⁄₄"
(41.3 cm)
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
GROUNDING INSTRUCTIONS
SAVE THESE INSTRUCTIONS
■ For all cord connected appliances:
The microwave oven must be grounded. In the event of
an electrical short circuit, grounding reduces the risk of
electric shock by providing an escape wire for the electric
current. The microwave oven is equipped with a cord
having a grounding wire with a grounding plug. The plug
must be plugged into an outlet that is properly installed
and grounded.
WARNING: Improper use of the grounding plug can
result in a risk of electric shock. Consult a qualified
electrician or serviceman if the grounding instructions are
not completely understood, or if doubt exists as to whether
the microwave oven is properly grounded.
Do not use an extension cord. If the power supply cord is
too short, have a qualified electrician or serviceman install
an outlet near the microwave oven.

Specyfikacje produktu

Marka: Whirlpool
Kategoria: Magnetostrykcja
Model: WMH76719CB

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Whirlpool WMH76719CB, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Magnetostrykcja Whirlpool

Whirlpool

Whirlpool MBF 200 S Instrukcja

7 Grudnia 2024
Whirlpool

Whirlpool WMF250G Instrukcja

4 Grudnia 2024
Whirlpool

Whirlpool Extra Space Crisp MWF 426 Instrukcja

4 Grudnia 2024
Whirlpool

Whirlpool JT 469 BL Instrukcja

4 Grudnia 2024
Whirlpool

Whirlpool MWF 259 B Instrukcja

4 Grudnia 2024
Whirlpool

Whirlpool MWSC 9133 SB Instrukcja

4 Grudnia 2024
Whirlpool

Whirlpool MWSC 933 SB Instrukcja

4 Grudnia 2024
Whirlpool

Whirlpool MWSC 9133 SX Instrukcja

4 Grudnia 2024
Whirlpool

Whirlpool MWSC 933 SW Instrukcja

4 Grudnia 2024
Whirlpool

Whirlpool WMCS7022RS Instrukcja

15 Października 2024

Instrukcje Magnetostrykcja

Najnowsze instrukcje dla Magnetostrykcja

Midea

Midea MM720CGE Instrukcja

10 Grudnia 2024
Continental Edison

Continental Edison CEMO20EBM Instrukcja

10 Grudnia 2024
Gorenje

Gorenje ECT631BSC Instrukcja

9 Grudnia 2024
Gorenje

Gorenje ECT693ORAB Instrukcja

9 Grudnia 2024
Gorenje

Gorenje ECS691USC Instrukcja

9 Grudnia 2024
Gorenje

Gorenje MO23ORAW Instrukcja

9 Grudnia 2024
Insignia

Insignia NS-MW7RC5 Instrukcja

9 Grudnia 2024
Haier

Haier JM-V16G Instrukcja

9 Grudnia 2024
Haier

Haier JM-17K Instrukcja

9 Grudnia 2024
GE

GE JX36DBB Instrukcja

8 Grudnia 2024