Instrukcja obsługi Whirlpool WHP80250

Whirlpool Suszarka bębnowa WHP80250

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Whirlpool WHP80250 (2 stron) w kategorii Suszarka bębnowa. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

Headquarters: PULS GmbH, Elektrastr. 6, 81925 Munich, Germany, www.pulspower.com

Germany +49 89 9278 0

China +86 512 62881820 France +33 478 668 941

North America +1 630 587 9780 Austria +43 2764 3213

Singapore +65 6684 2310 Switzerland +41 56 450 18 10

United Kingdom +44 1525 841001

The information in this document is believed to be accurate and reliable and may change without notice.

EN UC10.241 Installation Manual DC-UPS with Capacitor Storage 24V, 15A, 360W, 6kWs

DE UC10.241 Installationsanleitung DC-USV mit Kondensatorspeicher 24V, 15A, 360W, 6kWs

FR UC10.241 Manuel d'installation Sauvegarde CC avec condensateurs 24V, 15A, 360W, 6kWs

ES UC10.241 Manual de instalación SAI-CC con almancenamiento en condensadores 24V, 15A, 360W, 6kWs

IT UC10.241 Manuale di Installazione UPS in CC con mantenimento a condensatori 24V, 15A, 360W, 6kWs

PT UC10.241 Manual de instalação UPS-CC com armazenagem em condensadores 24V, 15A, 360W, 6kWs

Doc. ID: PU-406.015.50-Z (2018-03-27)

Read this first! English Vor Inbetriebnahme lesen! Deutsch

Before operating this device, please read this manual thoroughly and retain this manual for

future reference! This device may only be installed and put into operation by qualified

personnel. If damage or malfunction should occur during operation, immediately turn power

off and send device to the factory for inspection. The device does not contain serviceable

parts. The information presented in this document is believed to be accurate and reliable and

may change without notice. For any clarifications the English translation will be used.

Bitte lesen Sie diese Warnungen und Hinweise sorgfältig durch, bevor Sie das Gerät in Betrieb

nehmen. Bewahren Sie die Anleitung zum Nachlesen auf. Das Gerät darf nur durch

fachkundiges und qualifiziertes Personal installiert werden. Bei Funktionsstörungen oder

Beschädigungen schalten Sie sofort die Versorgungsspannung ab und senden das Gerät zur

Überprüfung ins Werk. Das Gerät beinhaltet keine Servicebauteile. Die angegebenen Daten

dienen allein der Produktbeschreibung und sind nicht als zugesicherte Eigenschaften im

Rechtssinne aufzufassen. Im Zweifelsfall gilt der englische Text.

WARNING Risk of electrical shock, fire, personal injury, or death: WARNUNG

Missachtung nachfolgender Punkte kann einen elektrischen

Schlag, Brände, schwere Unfälle oder Tod zur Folge haben:

- Turn power off before working on the device. Protect against inadvertent re-powering.

- Do not open, modify or repair the device.

- Use caution to prevent any foreign objects from entering the housing.

- Do not use in wet locations or in areas where moisture or condensation can be expected.

- Do not touch during power-on and immediately after power-off. Hot surfaces may cause

burns.

- Schalten Sie die Eingangsspannung vor Installations-, Wartungs- oder Änderungsarbeiten

ab und sichern Sie diese gegen unbeabsichtigtes Wiedereinschalten.

- Führen Sie keine Änderungen oder Reparaturversuche am Gerät durch. Gerät nicht öffnen!

- Verhindern Sie das Eindringen von Fremdkörpern, wie z.B. Büroklammern und Metallteilen.

- Betreiben Sie das Gerät nicht in feuchter Umgebung oder in einer Umgebung, bei der mit

Betauung oder Kondensation zu rechnen ist.

- Gehäuse nicht während des Betriebes oder kurz nach dem Abschalten berühren. Heiße

Oberflächen können Verletzungen verursachen.

A lire avant mise sous tension! Français Lea primero! Español

Veuillez lire ces instructions de montage et d'entretien avant de mettre l'alimentation sous

tension. Conservez ce manuel qui vous sera toujours utile. Cette alimentation ne doit être

installée que par du personnel qualifié et compétent. En cas de dommage ou

dysfonctionnement, coupez immédiatement la tension d’alimentation et retournez l’appareil à

l’usine pour vérification. ! L’alimentation ne contient pas de pièces échangeables Les

données indiquées dans ce document servent uniquement à donner une description du

produit et n'ont aucune valeur juridique. En cas de divergences, le texte anglais fait foi.

Conserve este manual como referencia para futuras consultas. La fuente de alimentación solo

puede ser instalada y puesta en funcionamiento por personal cualificado. Por favor lea

detenidamente este manual antes de conectar la fuente de alimentación. Si se produce un fallo

o mal funcionamiento durante la operación, desconecte inmediatamente la tensión de

alimentación. En ambos casos, el equipo debe ser inspeccionado en fábrica. La información

presentada en este documento es exacta y fiable en cuanto a la descripción del producto y

puede cambiar sin aviso. En casa de duda, prevalece el texto inglés.

AVERTISSEMENT

Prendre en compte les points suivants, afin

d'éviter toute détérioration électrique, incendie,

dommage aux personnes ou mort:

ADVERTENCIA

Riesgo de descarga eléctrica, incendio, accidente

grave o muerte:

- Mettre l’alimentation hors tension avant toute intervention sur celle-ci et s'assurer qu'il n'y

a pas risque de redémarrage.

- Ne pas ouvrir, modifier ou réparer l'alimentation.

- Veiller à ce qu'aucun objet ne rentre en contact avec l'intérieur de l'alimentation

(trombones, pièces métalliques).

- Ne pas faire fonctionner l'appareil dans un environnement humide ou dans un

environnement où il peut y avoir de la condensation.

- Ne pas toucher le carter pendant le fonctionnement ou directement après la mise hors

tension. Surface chaude risquant d’entraîner des blessures.

- Desconectar la tensión de red antes de trabajar en la fuente de alimentación. Evite una

posible reconexión involuntaria.

- No realizar ninguna modificación o reparación de la unidad. No abrir la unidad.

- Evitar la introducción en la carcasa de objetos extraños.

- No usar el equipo en ambientes húmedos. No operar el equipo en ambientes donde se

espere la formación de rocío o condensación.

- No tocar durante el funcionamiento ni inmediatamente después del apagado. El calor de la

superficie puede causar quemaduras graves.

Leggere prima questa parte! Italiano Leia primeiro! Portuguès

Prima di collegare il sistema di alimentazione elettrica si prega di leggere attentamente le

seguenti avvertenze. Conservare le istruzioni per la consultazione futura. Il sistema di

alimentazione elettrica deve essere installato solo da personale competente e qualificato. Se

durante il funzionamento si verificano anomalie o guasti, scollegare immediatamente la

tensione di alimentazione. In entrambi i casi è necessario far controllare l'apparecchio dal

produttore! I dati sono indicati solo a scopo descrittivo del prodotto e non vanno considerati

come caratteristiche garantite dell'apparecchio. In caso di differenze o problemi è valido il

testo inglese

Recomendamos a leitura cuidadosa das seguintes advertências e observações, antes de

colocar em funcionamento a fonte de alimentação. Guarde as Instruções para futura consulta,

em casos de dúvida. A fonte de alimentação deverá ser instalada apenas por profissionais da

área, tecnicamente qualificados. Se por acaso, durante a utilização ocorrer algum defeito de

funcionamento ou dano, desligue imediatamente a tensão de alimentação. Em ambos os casos,

será necessária uma verificação na Fábrica! Os dados mencionados têm como finalidade

somente a descrição do produto, e não devem ser interpretados como propriedades garantidas

no sentido jurídico. Em caso de duvidas aplica-se o texto em inglês.

AVVERTENZA

Il mancato rispetto delle seguenti norme può

provocare folgorazione elettrica, incendi, gravi

incidenti e perfino la morte:

ATENÇÃO

A não observância ou o incumprimento dos pontos a seguir

mencionados, poderá causar uma descarga elétrica, incêndios,

acidentes graves ou morte:

- Prima di eseguire interventi di installazione, di manutenzione o di modifica scollegare la

tensione di rete ed adottare tutti i provvedimenti necessari per impedirne il ricollegamento

non intenzionale.

- Non tentare di aprire, di modificare o di riparare da soli l'apparecchio.

- Impedire la penetrazione di corpi estranei nell'apparecchio, ad esempio fermagli o altri

oggetti metallici.

- Non far funzionare l'apparecchio in un ambiente umido. Non far funzionare l'apparecchio

in un ambiente soggetto alla formazione di condensa o di rugiada.

- Non toccare quando acceso e subito dopo lo spegnimento. La superficie calda può

causare scottature.

- Antes de trabalhos de instalação, manutenção ou modificação, desligue a tensão de

alimentação, protegendo-a contra uma nova ligação involuntária.

- Não efectue nenhuma modificação ou tentativa de reparação no aparelho. Quando

necessário contacte o seu distribuidor. Não abra o aparelho.

- Proteger a fonte de alimentação contra a introdução inadvertida de corpos metálicos, como

por ex., clipes ou outras peças de metal.

- Não usar o aparelho em ambientes húmidos. Não usar o aparelho em ambientes propensos

a condensações.

- Não tocar enquanto estiver em funcionamento, nem após a desligar. A superficie poderá

estar quente e provocar lesões.

EN UC10.241 Installation Manual

Product Description

The UC10.241 is an uninterruptible power supply controller (DC-UPS) with included storage

capacitors, which is used in combination with a 24V power supply to bridge power failures. When the

power supply provides sufficient voltages, the DC-UPS controller charges the capacitors. When the

power supply voltage fails, the energy stored in the capacitors is released to the DC bus in a regulated

process.

Intended Use

This device is designed for installation in an enclosure and is intended for commercial use, such as in

industrial control, process control, monitoring and measurement equipment or the like. Do not use this

device in equipment where malfunction may cause severe personal injury or threaten human life.

Installation Instructions

Install the device in an enclosure providing protection against electrical, mechanical and fire hazards.

Install the device onto a DIN-rail according to EN 60715 with the input terminals on the top of the unit.

The input can be powered from a regulated power supply or a similar DC source. The voltage between

the input and ground must not exceed 60Vdc continuously. The ripple voltage in the low frequency

range between 50Hz and 10kHz must be negligible when used in marine applications.

The input must be powered from a PELV or SELV source or an “Isolated Secondary Circuit” in order to

maintain a SELV or PELV output.

Use an appropriately sized 24V power supply, which can deliver the additional internal current

consumption, required to charge the capacitors.

Check for correct input polarity. The device will not operate when the voltage is reversed.

Make sure that the wiring is correct by following all local and national codes. Use appropriate copper

cables that are designed for a minimum operating temperature of 60°C for ambient temperatures up to

+40°C and 80°C for ambient temperatures up to +60°C. Ensure that all strands of a stranded wire

enter the terminal connection.

The device is designed for pollution degree 2 areas in controlled environments. No condensation or

frost is allowed.

The device is designed as “Class of Protection III” equipment according to IEC 61140.

The enclosure of the device provides a degree of protection of IP20.

A disconnecting means shall be provided for the output of the device.

The device is designed for convection cooling and does not require an external fan. Do not obstruct

airflow and do not cover ventilation grid!

Keep the following minimum installation clearances: 40mm on top, 20mm on the bottom, 5mm left and

right side. Increase the 5mm to 15mm in case the adjacent device is a heat source. When the device

is permanently loaded with less than 50%, the 5mm can be reduced to zero.

The device is designed for altitudes up to 6000m (19685ft).

The maximum surrounding air temperature is +60°C (+140°F). The operational temperature is the

same as the ambient or surrounding air temperature and is defined 2cm below the device.

The device is designed to operate in areas between 5% and 95% relative humidity.

Installation Instructions for Hazardous Location Areas

The device is suitable for use in Class I Division 2 Groups A, B, C, D locations and for use in Group II

Category 3 (Zone 2) environments.

Hazardous Location Classification: ATEX: EPS 15 ATEX 1 025 X, II 3G EX ec nC IIC T4 Gc

WARNING EXPLOSION HAZARDS!

Substitution of components may impair suitability for this environment.

Do not disconnect the device or change unit settings unless power has been switched o or the area

is known to be non-hazardous.

A suitable enclosure must be provided for the end product which has a minimum protection of IP54

and fulfils the requirements of the EN 60079-0.

Functional Description

The output is electronically protected against no-load, overload and short circuit and can supply any

kind of loads, including unlimited inductive loads and capacitive loads.

Do not apply return voltages from the load to the output terminals higher than 35V.

Green Status LED

This LED is on solid, when the capacitor is charged. During charging, the LED is flashing with a slow

frequency and rapid flashing is an indication of a buffer event.

Yellow Diagnoses LED

This LED reports an overload situation, a high temperature, an expired buffer time or an activated inhibit

input.

Red Warning LED

This LED indicates a failure in the input voltage or an activated PC-mode.

Inhibit Input

The inhibit input disables or stops buffering. In power supply mode, a continuous input of 10-30V is

required. During buffering, a short input of 10-30V for at least 250ms is required to stop buffering. The

current of the inhibit input is limited to 6mA by the DC-UPS control unit.

Ready and Buffering Relay Contacts

The Ready contact is closed when the capacitor is charged and the unit is ready to buffer.

The Buffering contact is closed when the unit is in buffer mode.

Contact ratings: 60Vdc 0.3A, 30Vdc 1A, 30Vac 0.5A for resistive loads.

PC-Mode Input

The PC-mode always turns the output off for at least 5s after a buffer event lasting longer than 1s,

independent of whether the 24V may have recovered during this time. This function ensures that the

PC gets a restart signal. To enable a safe shut-down of the system, the forced turn off of the output is

delayed with a constant time of 70s.To activate the PC-mode, connect the two pins marked with “PC-

mode” together on the signal connector together.

Technical Data

All values are typical figures specified at 24Vdc input voltage, 15A output

current in power supply mode at 25°C ambient, no charging and after a 5

minutes run-in time unless otherwise noted.

Input voltage DC 24V -20%/+25%

Minimum input voltage to

start charging and to

enable buffer mode

22.8Vdc

Transfer voltage to switch

into buffer mode

22.5Vdc

Internal current

consumption

1.1A Includes charging

current

Output in power supply mode:

Input to output voltage loss 230mV At 10A output load

330mV At 15A output load

Output current 15A Continuous

Output in buer mode:

Output voltage 22.45V At no output load

22.25V At 10A output load

Output current 15A Continuous

Buffer time 340s At 0.5A output current

39s At 5A output current

16.5s At 10A output current

9s At 15A output current

Charging time 16 minutes For initial charging

4 minutes 30s For recharging shortly

after a 5A buffer event

Power losses 4.6W At 10A output load

Temperature range -40°C to +60°C

Max. wire size (litz wire) 4mm² For power terminals

Wire size AWG AWG 20-10 For power terminals

Max. wire diameter 2.8mm For power terminals

Wire stripping length 10mm/ 0.4inch For power terminals

Max. wire size (litz wire) 1.5mm² For signal terminals

Wire size AWG AWG 24-16 For signal terminals

Max. wire diameter 1.5mm For signal terminals

Wire stripping length 8mm/ 0.3inch For signal terminals

Size (wxhxd) 126x124x117mm Without DIN-rail

Weight 1150g / 2.54lb

Functional Diagram

Boost

Converter Charger

Balancing

and

Safety

Circuits

Electronic

Current

Limiter Output

Diagnosis LED

Status LED

Controller

Warning

Buffering Contact

Ready Contact

(5)

(6)

(1)

(2)

(3)

(4)

Capacitors

Input Fuse,

Reverse Polarity Protection,

Return Current Protection

Temp

Input

Voltage

Monitor

Inhibit

(7)

(8)

PC-Mode

Input

Chassis

Ground

Wiring Scheme

Signals

OutputInput

DC-UPS

Load

Power

Supply

Output

Input

L N

LED Signal Pattern

Ready

Charging

Buffering

Green Status LED:

Current Overload

High Temperature

Buffer Time

Expired

Inhibit Active

Yellow Diagnosis LED:

Check Input

Voltage

Red Warning LED:

PC-Mode

Activated

Specyfikacje produktu

Marka:	Whirlpool
Kategoria:	Suszarka bębnowa
Model:	WHP80250

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Whirlpool WHP80250, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Suszarka bębnowa Whirlpool

Whirlpool FFT M11 8X3BY SPT Instrukcja

11 Stycznia 2025

Whirlpool FFT CM10 8BB NA Instrukcja

11 Stycznia 2025

Whirlpool FFT D 9X3SK EX Instrukcja

11 Stycznia 2025

Whirlpool FFT M22 8X3B SPT Instrukcja

11 Stycznia 2025

Whirlpool FFT M22 9X2WS EE Instrukcja

11 Stycznia 2025

Whirlpool FFTN M11 82 SPT Instrukcja

11 Stycznia 2025

Whirlpool FFT M22 9X2SBX GCC Instrukcja

10 Stycznia 2025

Whirlpool W6 D94SB IT Instrukcja

10 Stycznia 2025

Whirlpool FFT M11 9X2BS BE R Instrukcja

5 Stycznia 2025

Whirlpool FFT M11 8X2BS BE R Instrukcja

5 Stycznia 2025

Instrukcje Suszarka bębnowa

Najnowsze instrukcje dla Suszarka bębnowa

Bauknecht trkk 7846 Instrukcja

15 Stycznia 2025

AEG T8DEN86CS Instrukcja

15 Stycznia 2025

Candy GCS 91013A2 Instrukcja

15 Stycznia 2025

Zanussi ZDP7204PZ Instrukcja

15 Stycznia 2025

Bauknecht TRKA Koblenz 4590 Instrukcja

15 Stycznia 2025

Bauknecht trkk 6840 Instrukcja

15 Stycznia 2025

AEG-Electrolux Lavatherm 310 Instrukcja

14 Stycznia 2025

Hotpoint NWXR483GGWW Instrukcja

14 Stycznia 2025

Zanussi ZDC82B4SW Instrukcja

14 Stycznia 2025

Bauknecht trk advance Instrukcja

14 Stycznia 2025