Instrukcja obsługi Whirlpool MK2227AS

Whirlpool Magnetostrykcja MK2227AS

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Whirlpool MK2227AS (12 stron) w kategorii Magnetostrykcja. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/12
MICROWAVE OVEN BUILT-IN TRIM KIT
INSTALLATION INSTRUCTIONS
Built-In Trim Kit Models MK2227 MK2220
UL listed for use over any electric or gas built-in oven, up to 30" (76.2 cm) wide
INSTRUCTIONS D’INSTALLATION
GARNITURE ENCASTRÉE POUR FOUR À MICRO-ONDES
Garniture encastrée pour modèles MK2227 MK2220
Homologations UL pour utilisation au-dessus de tous les fours encastrés électriques ou à gaz, jusqu’à 30" (76,2 cm) de largeur
MICROWAVE OVEN SAFETY
Table of Contents / Table des matières
MICROWAVE OVEN SAFETY ..................................................1
INSTALLATION INSTRUCTIONS.............................................2
Tools and Parts ......................................................................2
Location Requirements..........................................................2
Required Cutout Dimensions.................................................2
Trim Kit Frame Dimensions....................................................2
Electrical Requirements .........................................................3
Prepare Microwave Oven.......................................................3
Prepare Cutout/Cabinet Opening ..........................................3
Install the Microwave Oven....................................................4
Install Trim Kit Frame .............................................................5
SÉCURITÉ DU FOUR À MICRO-ONDES...........................................7
INSTRUCTIONS D’INSTALLATION....................................................7
Outillage et pièces.............................................................................7
Exigences d'emplacement................................................................7
Dimensions nécessaires de l'ouverture d'encastrement..................8
Dimensions du cadre de la trousse de garniture..............................8
Spécifications électriques .................................................................8
Préparation du four à micro-ondes...................................................9
Préparation de l'ouverture d'encastrement/dans le placard............9
Installation du four à micro-ondes ..................................................10
Installation du cadre de la trousse de garniture .............................11
W10434148A
You can be killed or seriously injured if you don't immediately
You can be killed or seriously injured if you don't follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING
2
INSTALLATION INSTRUCTIONS
Tools and Parts
Tools Needed
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools
listed here.
Parts Supplied (not shown to scale)
Location Requirements
The microwave oven may be installed over a built-in oven. If
installing over a built-in oven, make sure there is a minimum of 3"
(7.6 cm) between the top of the lower oven cutout and the
microwave oven cutout floor.
The microwave oven may also be installed in a cabinet by itself
(without a built-in oven below). For best usability, we recommend
a minimum distance of 36" (91.4 cm) from the floor to the cutout
floor.
Make sure the surrounding cabinetry has clearance to open and
close freely. Allow a clearance of at least 1⁹⁄₁₆" (4.0 cm) below the
cutout floor (3" [7.6 cm] for installation above a built-in oven), and
a clearance of at least 2" (5.1 cm) above the cutout opening.
Required Cutout Dimensions
NOTES:
■ Height dimension is critical: 17" (43.2 cm) minimum, 17¹⁄₈"
(43.5 cm) maximum.
■Width and depth measurements have ±1/16" (2 mm)
tolerance.
■ 3" (7.6 cm) minimum dimension is from lower oven cutout
ceiling to microwave oven cutout floor.
■Trim kit frame extends 1¹⁄₁₆" (2.7 cm) above and below the
cutout opening.
Trim Kit Frame Dimensions
*27" (68.6 cm) trim kit
**30" (76.2 cm) trim kit
■ Measuring tape
■ Pencil
■ Phillips screwdriver
■ Drill
■ 7/64" drill bit
Rails (2) Bottom duct Trim kit frame
Short screws (14)
(11 + 3 extra)
Long wood screws (6 - painted)
(4 + 2 extra)
A. Upper cabinet
B. Microwave oven cutout
C. Lower oven cutout
D. Lower cabinets
E. Floor
3"
(7.6 cm)
BB
D
36"
(91.4 cm)
C
2"
(5.1 cm)
2"
(5.1 cm)
1 "⁹⁄₁₆
(4.0 cm)
A
E
A. Trim kit frame overhang
B. Cutout for lower oven
22 "³⁄₄
(57.8 cm)
WidthWidth
25¹⁄₂" (64.8 cm)
3"
(7.6 cm)
A
1 "¹⁄₁₆
(2.7 cm)
1 "¹⁄₁₆
(2.7 cm)
B
17 " (43.5 cm)¹⁄₈
max.
17" (43.2 cm)
min.
26⁷⁄₈" (68.2 cm)**
29³⁄₄" (75.6 cm)**
¹³⁄₁₆" (2.1 cm)*
*
2³⁄₈" (6.0 cm)**
25" (63.5 cm)
13¹⁄₁₆
"
(33.2 cm
)
1" (2.5 cm)
18 "⁷⁄₈
(47.9 cm)
2¹⁵⁄₁₆"
(7.5 cm)
3
Electrical Requirements
Observe all governing codes and ordinances.
Required:
■ A 120 volt, 60 Hz, AC only, 15- or 20-amp electrical supply
with a fuse or circuit breaker.
Recommended:
■ A time-delay fuse or time-delay circuit breaker.
■ A separate circuit serving only this microwave oven.
Prepare Microwave Oven
1. Unplug microwave oven before proceeding with installation.
2. Remove any loose items inside microwave oven.
3. Gently turn microwave oven onto its top, with the door facing
forward (toward installer).
4. Align the #33 holes on the microwave oven bottom with the
#33 holes on the rails, as shown, making sure the flanges are
forward and pointing up.
5. Secure the rails to the microwave oven bottom using four
short screws through the #33 hole sets.
Prepare Cutout/Cabinet Opening
1. On the cutout floor, find and mark the centerline.
2. Place the bottom duct in the opening, with the flange resting
against the bottom front facing of the opening.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
GROUNDING INSTRUCTIONS
SAVE THESE INSTRUCTIONS
■ For all cord connected appliances:
The microwave oven must be grounded. In the event of
an electrical short circuit, grounding reduces the risk of
electric shock by providing an escape wire for the electric
current. The microwave oven is equipped with a cord
having a grounding wire with a grounding plug. The plug
must be plugged into an outlet that is properly installed
and grounded.
WARNING: Improper use of the grounding plug can
result in a risk of electric shock. Consult a qualified
electrician or serviceman if the grounding instructions are
not completely understood, or if doubt exists as to whether
the microwave oven is properly grounded.
Do not use an extension cord. If the power supply cord is
too short, have a qualified electrician or serviceman install
an outlet near the microwave oven.
A. Rails (2)
B. Microwave oven bottom
C. Short screws (4)
D. Flanges
E. Door
A. Cutout floor
B. Centerline
C. Bottom duct
D. Bottom duct flange
E. Front facing
A B C
D E
A
B
C
D E

Specyfikacje produktu

Marka: Whirlpool
Kategoria: Magnetostrykcja
Model: MK2227AS

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Whirlpool MK2227AS, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Magnetostrykcja Whirlpool

Whirlpool

Whirlpool MBF 200 S Instrukcja

7 Grudnia 2024
Whirlpool

Whirlpool WMF250G Instrukcja

4 Grudnia 2024
Whirlpool

Whirlpool Extra Space Crisp MWF 426 Instrukcja

4 Grudnia 2024
Whirlpool

Whirlpool JT 469 BL Instrukcja

4 Grudnia 2024
Whirlpool

Whirlpool MWF 259 B Instrukcja

4 Grudnia 2024
Whirlpool

Whirlpool MWSC 9133 SB Instrukcja

4 Grudnia 2024
Whirlpool

Whirlpool MWSC 933 SB Instrukcja

4 Grudnia 2024
Whirlpool

Whirlpool MWSC 9133 SX Instrukcja

4 Grudnia 2024
Whirlpool

Whirlpool MWSC 933 SW Instrukcja

4 Grudnia 2024
Whirlpool

Whirlpool WMCS7022RS Instrukcja

15 Października 2024

Instrukcje Magnetostrykcja

Najnowsze instrukcje dla Magnetostrykcja

Midea

Midea MM720CGE Instrukcja

10 Grudnia 2024
Continental Edison

Continental Edison CEMO20EBM Instrukcja

10 Grudnia 2024
Gorenje

Gorenje ECT631BSC Instrukcja

9 Grudnia 2024
Gorenje

Gorenje ECT693ORAB Instrukcja

9 Grudnia 2024
Gorenje

Gorenje ECS691USC Instrukcja

9 Grudnia 2024
Gorenje

Gorenje MO23ORAW Instrukcja

9 Grudnia 2024
Insignia

Insignia NS-MW7RC5 Instrukcja

9 Grudnia 2024
Haier

Haier JM-V16G Instrukcja

9 Grudnia 2024
Haier

Haier JM-17K Instrukcja

9 Grudnia 2024
GE

GE JX36DBB Instrukcja

8 Grudnia 2024