Instrukcja obsługi Whirlpool FWSD81283BV EE
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Whirlpool FWSD81283BV EE (4 stron) w kategorii Pralki. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/4
EN
Quick guide
THANK YOU FOR BUYING A WHIRLPOOL PRODUCT.
In order to receive a more complete assistance,
please register your appliance on
www.whirlpool.eu/register
Before using the appliance carefully read the Health and Safety guide.
Before using the machine, it is imperative that the transport bolts are removed. For more detailed
instructions on how to remove them, see the Installation Guide.
PROGRAMME CHART
1. “ON/OFF” button
2. Programme selector
3. “Temperature” button
60°
40°
4. “Spin” button
5. “Start delay” button
6. “Start/Pause” button
7. Option buttons
8. “Key lock“button
INDICATORS
Door can be opened
Washing phase
Indicates washing phase of the cycle
Failure: Call Service
Refer to Troubleshooting section
Failure: Water lter clogged
Water cannot be drained; water lter
might be blocked
Failure: Water tap closed
No or not sucient inlet water. “Beep”
sound every 5 seconds.
In the event of any failures, refer to the
Troubleshooting section in USER MANUAL
CONTROL PANEL
2.1. 6.3. 4. 5.
8.7. 7.
PRODUCT DESCRIPTION
1. Worktop
2. Detergent dispenser
3. Control panel
4. Door handle
5. Door
6. Water lter - behind plinth
7. Plinth (removable)
8. Adjustable feet (4)
1.
2.
7.
3.
4.
5.
6.
8.
DETERGENT DISPENSER
Main wash compartment
Detergent for the main wash, stain remover
or water softener. For a liquid detergent it is
recommended to use removable plastic partition
A (supplied) for a proper dosage. If powder
detergent is used, place the partition into slot B.
Prewash compartment
Detergent for the prewash.
Softener compartment
Fabric softener. Liquid starch.
Pour in softener or starch solution only up to the “max” mark.
Release button
Press to remove tray for cleaning.
AB
This data may dier in your home due to changing conditions in inlet water temperature,
water pressure etc. Approximate programme duration values refer to the default setting of the
programmes, without options.
** After programme end and spinning with maximum selectable spin speed, in default
programme setting.
*** The duration of the programme is shown on the display.
6th Sense - the sensor technology adapts water, energy and programme duration to your wash
load.
Eco Cotton - Test wash cycles in compliance with regulations 1061/2010
These are the reference programs for the energy label. Set this wash cycles with a
temperature of 40°C or 60°C. They are the most ecient programmes in terms of energy
and water consumption for washing normally soiled cotton laundry. The actual water
temperature may dier from the declared one.
For all Test Institutes:
Long wash cycle for cottons: set wash cycle with a temperature of 40°C.Cotton
Synthetic program along: set wash cycle Synthetics
with a temperature of 40°C.
Max load 8 Kg
Power consumption in o -mode 0.5 W / in left-on mode 8 W Detergents and additives Recommend-
ed detergent
Residual
dampness % (**)
Energy
consumption kWh
Total water lt
Programme
Temperatures Max.
spin
speed
(rpm
Max
load
(kg
Duration
(Minutes
Prewash Main
wash Softener Pow-
der Liquid
Default Range
Mixed 40°C - 40°C 4 –1000 *** – – – –
Whites 60°C - 90°C 81200 *** (90°) – – –
Cotton 40°C - 60°C 8 230 –1200 53 0,89 88
Eco Cotton 60°C 60°C 8 210 –1200 53 1,17 55
40°C 8 230 –1200 53 0,89 88
Bed linen 60°C - 60°C 8 –1200 *** – – –
Sport 40°C - 40°C 4 –600 *** – – – –
Duvets 30°C - 30°C 2 –1000 *** – – – –
Steam Refresh – – – 1.5 – – – – – – – –***
Spin+Drain – – 8 – – – – – – – –1200 ***
Rinse+Spin – – 8 – –1200 *** – – – – –
Rapid 30’ 30°C - 30°C 3 –800 *** – – – –
Colours 15° 15°C 15°C 4 – 1000 *** – – – –
Silk 30°C - 30°C 1 –– *** – – – –
Wool 40°C - 40°C 1.5 –800 *** – – – –
Delicates 30°C - 30°C 1 –– *** – – – –
Synthetics 40°C - 60°C 4 –1200 200 32 0,80 78
Dosing required Dosing optional
PROGRAMMES
For choosing the appropriate programme for your kind of
laundry, always respect the instructions on the care labels of
the laundry. The value given in the tub symbol is the maximum
temperature possible for washing the garment.
Mixed
For washing lightly to normally soiled resilient garments in cotton, linen,
synthetic bres and mixed bres.
Whites
For washing normally to heavily soiled towels, underwear, table and bed
linen, etc in resilient cotton and linen. Only when the temperature is
selected at 90°C the cycle is provided with a prewash phase before main
washing phase. In this case it is recommended to add detergent both, in the
prewash and main wash section.
Cotton
Normally to heavily soiled and robust cottons .
Eco Cotton
For washing normally soiled cotton garments. At 40°c and 60°C, this is the
standard cotton programme and the most ecient in terms of water and
energy consumption.
Bed linen
Use this programme to wash bed linen an towels in one single cycle. It
optimises softner performance and helps you save time and energy. We
recommend to use powder detergent.
Sport
For washing lightly soiled sports clothing (tracksuits, shorts, etc.). For best
results, we recommend not exceeding the maximum load indicated in the
‚‘‘‘PROGRAMME CHART‘‘. We recommend using liquid detergent , and adding
the amount suitable for half-load.
Duvets
Designed for washing eiderdown padded items such as double or single
duvets, cushions and anoraks. It is recommended to load such padded
items in the drum with the edges folded inwards and not to exceed ¾ of
the drum’s volume. For optimal washing, we recommend using a liquid
detergent.
Steam Refresh
This programme refreshes garments by removing bad odours and relaxing
the bres (1.5 kg, roughly 3 items). Insert dry items only (that are not dirty)
and select programme “Steam Refresh”. Garments will be a little damp
at the end of the cycle and can be worn after a few minutes. The “Steam
Refresh” programme makes ironing easier.
! Not recommended for wool or silk garments.
! Do not add softeners or detergents.
Spin+Drain
Spins the load then empties the water. For resilient garments. If you exclude
the spin cycle, the machine will drain only
Rinse+Spin
Rinses and the spins. For resilient garments.
Rapid 30’
For washing lightly soiled garments quickly. This cycle lasts only 30 minutes,
saving time and energy.
Colours 15°
This cycle helps protect colours by washing in cold water (15°C) and uses
less energy to heat the water while still oering satisfactory wash results.
Suitable for lightly soiled, ustained garments. This cycle oers wash results
comparable to 40°c mixed at just 15°C.
Silk
Use this cycle to wash all silk garments. We recommend the use of special
detergent which has been designed to wash delicate clothes.
Wool
All wool garments can be washed using programme ‚“Wool“ even those
carryng the “hand-wash only “ label. For best results, use special detergents
and do not exceed max kg declaration of laundry.
Delicates
For washing particularly delicate garments. Preferably turn garments inside
out before washing.
Synthetics
For washing soiled garments made from synthetic bres (such as polyester,
polyacrylic, viscose, etc.) or cotton/synthetic blends.
FIRST TIME USE
The rst time the machine is switched on, you will be asked to select the
language and the display will automatically show the language selection
menu.
To select the desired language press the “Temperature”
60°
40°
button
or “Start delay” button; to conrm the selection press the “Spin”
button.
To change the language switch o the washing machine and press buttons
“Key lock” , “Intensive rinse” and “FreshCare+” simultaneously
until an alarm is heard: the language-selection menu will be displayed
again.
To remove any residues from the manufacturing process. Select the
“Cotton” programme at a temperature of 60°C. Add a small amount of
heavy duty detergent to the main wash compartment of the detergent
dispenser (maximum 1/3 of the quantity recommended by the detergent
manufacturer for lightly soiled laundry). Start the programme without
adding any laundry.
DAILY USE
Prepare your laundry according to the recommendations in the “HINTS
AND TIPS” section. Load the laundry, close the door, open the water tap
and press the “ON/OFF” button to switch the washing machine on,
the “Start/Pause” button ashes. Turn the programme selector to the
desired programme and select any option if needed. The temperature
and spin speed shown on the display can be changed by pressing the
“Temperature”
60°
40°
button or the “Spin” button. Pull out the detergent
dispenser and add the detergent (and additives/softener) now. Observe the
dosing recommendations on the detergent pack. Then close the detergent
dispenser and press the “Start/Pause” button. The “Start/Pause”
button will lights up and the door will be locked.
PAUSE A RUNNING PROGRAMME
To pause the wash cycle, press the button “Start/Pause” again; the
indicator light will ash. If the symbol is illuminated, the door may be
opened. To start the wash cycle from the point at which it was interrupted,
press the button again.
OPEN THE DOOR, IF REQUIRED
Before starting and after end of a programme, the “Door open” symbol
lights to show the the door can be opened. As long as a wash programme is
running, the door remains locked. To open the door while a programme is
in progress, press the “Start/Pause” button. Provided the water level and/
or temperature is/are not too high, the “door open” indicator lights up
and you can open the door. For example to add/ remove laundry. Press the
“Start/Pause” button again to continue the programme.
PROGRAMME END
The “Door open” indicator lights up, and the display shows “Cycle end”.
To switch o the washing machine after programme end press the “ON/
OFF” button, the lights go o. If you do not press “ON/OFF” button,
the washing machine will switch o automatically after about a half of an
hour. Close the water tap. Open the door and unload the machine. Leave
the door ajar to allow the drum to dry.
OPTIONS
! If the selected function is incompatible with the set programme, the
incompatibility will be signalled by a buzzer (3 beeps) and the wording
“No Selection” will appear on the display.
! If the selected function is incompatible with another previously set
function, the wording will appear on the display and the “No Selection”
function will not be enabled.
Clean+
Clean+ is an option working on 3 dierent levels (Intensive, Daily and Fast)
that are specially designed to set the right washing action, depending on
your cleaning needs:
Intensive: this option is designed for high levels of dirtiness, removing most
stubborn stains.
Daily: this option is designed to remove everyday stains.
Fast: this option is designed to remove lightly soiled stains.
Intensive rinse
By selecting this option, the eciency of the rinse is increased and optimal
detergent removal is guaranteed. It is particularly useful for sensitive skin.
Press the button once, two or three times to select an additional 1, 2 or 3
rinses after the standard cycle rinse and remove all traces of detergent.
Press the button again to go back to the “Normal rinse” rinse type.
Delay Timer
To set the selected programme to start at a later time , press the button
to set the desired delay time. or “Waiting” “Starts in” is indicated on the
display when this option is enabled. To cancel the delayed start, press the
button again until the value ‚‘‘--:--‘‘ is shown on the display.
FreshCare+
This option enhances washing performance by generating steam to inhibit
the proliferation of the main bad odour sources inside the machine. After
steam phase, the washing machine will perform gentle tumbling through
slow rotations of the drum. FreshCare+ option starts after the cycle ends for
a maximum duration of 6h and you can interrupt at any time by pressing
any button on control panel or turning the knob.
(*) Wait around 5’ before open the door.
Steam Hygiene
This option enhances washing performance by generating steam during
the wash cycle that eliminates any bacteria from bres while treating them
at the same time. Place the laundry in the drum, choose a compatible
programme and select option “ “.
! The steam generated during washing machine operation may cause the
porthole door to become hazy.
Easy Iron
By selecting this function, the wash and the spin cycles will be modied in
order to reduce the formation of creases.
Temperature
Every programme has a predened temperature. If you want to change the
temperature, press the “Temperature”
60°
40°
button. The value appears on
the display.
Spin
Every programme has a predened spin speed. If you want to change the
spin speed, press the “Spin” button. The value appears on the display.
Demo mode
This appliance is equipped with Demo mode function. For more
information see the USER MANUAL/ Demo Mode.
KEY LOCK
To lock the control panel, press and hold the “KEY LOCK” button for
approximately 3 seconds. When the display visualises “KEY LOCK ON” the
control panel is locked (with the exception of the ON/OFF button). This
prevents unintentional changes to programmes, especially with children
near the machine. To unlock the control panel, press and hold the “KEY LOCK”
button for approximately 3 seconds.
BLEACHING
If you wish to bleach the laundry, load the washing machine and set the
“Rinse+Spin” programme.
Start the machine and wait for it to complete the rst water lling cycle
(roughly 2 minutes). Put the machine in pause mode by pressing the
“Start/Pause” button , open the detergent drawer and pour the bleach
(observe the recommended doses indicated on the package) into the
main wash compartment where the partition was previously mounted.
Restart the cycle by pressing the “Start/Pause” button .
If desired, it is possible to add fabric softener into the appropriate
compartment of the detergent drawer.
HINTS AND TIPS
Sort your laundry according to
Type of fabric/care label (cotton, mixed bres, synthetics, wool, handwash
items). Colour (separate coloured and white items, wash new coloured
items separately). Delicates (wash small items – like nylon stockings – and
items with hooks – like bras – in a cloth bag or pillow case with zip).
Empty all pockets
Objects like coins or lighters can damage your laundry as well as the drum.
DESCALE AND CLEAN PROCEDURE
A message on the display will regularly (roughly every 50 cycles) advise the
user to run an automatic cleaning cycle to clean the washing machine and
combat limescale build-up and bad odours.
For optimal maintenance we suggest using WPRO Limescale and grease
remover, according to the instructions shown on the package. The product
can be purchased by contacting the technical assistance service or through
the website www.whirlpool.eu.
Whirlpool declines all liability for any damages to the appliance caused by the
use of other cleaning products for washing machines available on the market.
CLEANING & MAINTENANCE
For any cleaning and maintenance, switch o and unplug the washing
machine. Do not use ammable uids to clean the washing machine.
Cleaning the outside of the washing machine
Use a soft damp cloth to clean the outer parts of the washing machine. Do
not use glass or general purpose cleaners, scouring powder or similar to
clean the control panel – these substances might damage the printing
Checking the water supply hose
Check the inlet hose regularly for brittleness and cracks. If damaged, replace
it by a new hose available through our After-Sales Service or your specialist
dealer. Depending on the hose type:
If the inlet hose has a transparent coating, periodically check if the colour
intensies locally. If yes, the hose may have a leak and should be replaced.
Cleaning the mesh lters in the water supply hose
Close the tap and loosen the inlet hose on the tap. Clean the internal mesh
lter and screw the water inlet hose back onto the tap. Now unscrew the
inlet hose on the rear of the washing machine. Pull o the mesh lter from
the washing machine connection with universal pliers and clean it. Ret the
mesh lter and screw the inlet hose on again. Turn on the tap and ensure
that the connections are completely water-tight.
Cleaning the water lter / draining residual water
If you used a hot wash programme, wait until the water has cooled down before
draining any water. Clean the water lter regularly, to avoid that the water
cannot drain after the wash due to obstruction of the lter. If the water cannot
drain, the display indicates that the water lter may be clogged.
Remove the plinth by using the removable plastic partition of the detergent
dispenser: push downwards one side of the plinth with your hand, then
push the removable plastic partition into the gap between plinth and front
panel and pry open the plinth. Place a broad, at container beneath the
water lter, to collect the drain water. Slowly turn the lter counterclockwise
until water ows out. Let the water ow out, without removing the lter.
When the container is full, close the water lter by turning it in clockwise.
Empty the container. Repeat this procedure until all the water has drained.
Lay a cotton cloth beneath the water lter, which can absorb a small
amount of rest water. Then remove the water lter by turning it out anti
clockwise. Clean the water lter: remove residues in the lter and clean it
under running water. Insert the water lter and reinstall the plinth: Reinsert
the water lter again by turning it in clockwise direction. Make sure to turn
it in as far as it goes; the lter handle must be in vertical position. To test
water tightness of the water lter, you can pour about 1 liter of water into
the detergent dispenser. Then reinstall the plinth.
Cleaning the detergent dispenser
Remove the detergent dispenser by pressing on the release button and at
the same time pulling out the detergent dispenser. Remove the insert from
the detergent dispenser, as well as the insert of the softener compartment.
Clean all parts under running water, removing all detergent or softener
residues. Wipe the parts dry with a soft cloth. Reinstall the detergent
dispenser and push it back into the detergent compartment.
ACCESSORIES
Contact our After-Sales Service to check if the following accessories are
available for your washing machine model.
Stacking kit shelf
By which your dryer can be xed on top of your washing machine to save
space and to facilitate loading and unloading your washing machine in the
higher position.
TRANSPORT AND HANDLING
Never lift the washing machine by holding it at the worktop.
Pull out the mains plug, and close the water tap. Make sure that door and
detergent dispenser are properly closed. Disconnect the inlet hose from the
water tap, and remove the drain hose from your draining point. Remove all
rest water from the hoses, and x them so that they cannot get damaged
during transport. Ret the transport bolts. Follow the instructions for
removing the transport bolts in the INSTALLATION GUIDE in reverse order.
Specyfikacje produktu
| Marka: | Whirlpool |
| Kategoria: | Pralki |
| Model: | FWSD81283BV EE |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Whirlpool FWSD81283BV EE, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Pralki Whirlpool
15 Października 2024
15 Października 2024
15 Października 2024
13 Października 2024
13 Października 2024
13 Października 2024
13 Października 2024
12 Października 2024
12 Października 2024
11 Października 2024
Instrukcje Pralki
- Pralki Bauknecht
- Pralki Samsung
- Pralki Electrolux
- Pralki DeLonghi
- Pralki AEG
- Pralki Balay
- Pralki Beko
- Pralki Teka
- Pralki LG
- Pralki Amica
- Pralki Gorenje
- Pralki Sharp
- Pralki Russell Hobbs
- Pralki Simpson
- Pralki Bosch
- Pralki Candy
- Pralki Miele
- Pralki Midea
- Pralki Hisense
- Pralki Infiniton
- Pralki Panasonic
- Pralki Baumatic
- Pralki Black & Decker
- Pralki OK
- Pralki Adler
- Pralki Hoover
- Pralki Toshiba
- Pralki Westinghouse
- Pralki Maytag
- Pralki Domo
- Pralki GE
- Pralki Brandt
- Pralki Siemens
- Pralki Haier
- Pralki Cylinda
- Pralki Hyundai
- Pralki Blomberg
- Pralki Fisher & Paykel
- Pralki Indesit
- Pralki Dyson
- Pralki Hotpoint
- Pralki Kenwood
- Pralki Thor
- Pralki Amana
- Pralki Hotpoint Ariston
- Pralki Bomann
- Pralki CDA
- Pralki Philco
- Pralki Neff
- Pralki Corbero
- Pralki Zanussi
- Pralki Fagor
- Pralki Koenic
- Pralki Ardo
- Pralki Manta
- Pralki Pyle
- Pralki KitchenAid
- Pralki Exquisit
- Pralki Arçelik
- Pralki Hanseatic
- Pralki Sanyo
- Pralki SVAN
- Pralki Caple
- Pralki AEG-Electrolux
- Pralki Bush
- Pralki New Pol
- Pralki Kenmore
- Pralki VOX
- Pralki Insignia
- Pralki Orima
- Pralki Kernau
- Pralki Hitachi
- Pralki Zerowatt
- Pralki Frigidaire
- Pralki RCA
- Pralki Kelvinator
- Pralki Gaggenau
- Pralki Avanti
- Pralki Asko
- Pralki Esatto
- Pralki Daewoo
- Pralki Scandomestic
- Pralki Ignis
- Pralki Magic Chef
- Pralki Constructa
- Pralki Euromaid
- Pralki Atlas
- Pralki Zanker
- Pralki Ariston
- Pralki Tricity Bendix
- Pralki Saturn
- Pralki Nordland
- Pralki Zanussi-electrolux
- Pralki Rasonic
- Pralki John Lewis
- Pralki Prima
- Pralki Iberna
- Pralki Logik
- Pralki Currys Essentials
- Pralki Alhafidh
- Pralki Hoover-Helkama
- Pralki Defy
- Pralki Servis
- Pralki Schulthess
- Pralki Marijnen
- Pralki Otsein-Hoover
- Pralki Campomatic
- Pralki Premium
- Pralki White Knight
- Pralki Nordmende
- Pralki Friac
- Pralki Dexter
- Pralki Costway
- Pralki Elba
- Pralki Everglades
- Pralki Saivod
- Pralki Freggia
- Pralki Edesa
- Pralki EAS Electric
- Pralki Lloyd
- Pralki Speed Queen
- Pralki WhiteLine
- Pralki Roper
- Pralki Estate
- Pralki Fram
- Pralki Stoves
- Pralki Edy
- Pralki Upo
- Pralki Trieste
- Pralki Videocon
- Pralki Neufunk
Najnowsze instrukcje dla Pralki
15 Października 2024
15 Października 2024
15 Października 2024
15 Października 2024
15 Października 2024
15 Października 2024
14 Października 2024
14 Października 2024
14 Października 2024
14 Października 2024