Instrukcja obsługi Whirlpool FFT M11 9X2BY EE

Whirlpool Suszarka bębnowa FFT M11 9X2BY EE

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Whirlpool FFT M11 9X2BY EE (56 stron) w kategorii Suszarka bębnowa. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/56

THANK YOU FOR BUYING A WHIRLPOOL PRODUCT.

In order to receive a more complete assistance,

please register your product on

www.whirlpool.eu/register

PLEASE SCAN THE QR CODE ON YOUR APPLIANCE IN ORDER TO REACH MORE INFORMATION.

Quick guide

Before using the appliance carefully

read the Safety Instruction.

The wool drying cycle of this machine

has been approved by The Woolmark

Company for the drying of wool

garments labelled as “hand wash”

provided that the garments are dried

according to the instructions issued

by the manufacturer of this machine.

Follow the garment care label for other

laundry instructions. . The Woolmark symbol is a Certiﬁ cation

mark in many countries.

M1768

DAILY USE

Doing this will keep your machine working at its BEST:

- remember to empty your water tank after each drying

cycle.

- remember to clean your lters after each drying cycle.

Refer to the Care & Maintenance section.

1. Plug the dryer into the power supply socket.

2. Open the door and load garments; always refer to instructions on

clothing labels and the max loads indicated in the programme

section. Empty pockets. Make sure garments do not get caught

between the door and/or the door filter. Do not load items that

are dripping wet. Do not tumble dry large, very bulky items. For

optimal drying result, garments should be loaded one by one.

3. Close the door.

4. Press the "On/Off" button.

5. Select the most suitable programme

for the type of fabric in

that load.

6. Select the options, if necessary.

7. Press the "

Start/Pause"

button to begin drying.

8. At the end of the drying cycle, a buzzer will beep. An indicator on

the control panel signals the end of the cycle. Turn the machine

off by pressing the "On/Off" button, open the door and pull the

clothing immediately out to prevent the formation of creases on

laundry.

If the machine is not switched off manually, after about a quarter

of an hour from the end of the cycle , the appliance turns off

automatically to save energy.

Note that some models perform a final cool tumble phase, for this

reason the fabrics may not feel hot.

In case of power failure, it is necessary to press the "Start/Pause"

button to restart the cycle

Opening the door during the cycle

The tumble dryer door can be opened at any time during the cycle

to check progress and remove any garments already dry.

However, since opening the door can extend the drying time, the

recommendation is to keep the door closed throughout the cycle

process to save time and energy.

After closing the door, press the "Start/Pause" button within 15

minutes to resume the machine operation.

NOTE: in any case, the drying cycle must be completed to ensure

the condenser auto-cleaning phase is ﬁnalized.

CARE LABEL

Always check the care labels, especially when placing garments in

the tumble dryer for the ﬁ rst time. Below are the most commonly

used symbols:

May be tumble dried.

Do not tumble dry.

Tumble dry – high heat.

Tumble dry – low heat.

FIRST TIME USE

Make sure that the water tank is correctly inserted.

The dryer must be installed in a room with a temperature

ranging between 5°C and 35°C to ensure proper operation.

Before you use your dryer ensure that it has been in a upright

position for at least 6 hours.

CONTROL PANEL

1 On/Oﬀ button (hold for Reset)

2 Programme selection knob

3 Start/Pause button

Options buttons*

4 Dryness level

5 Start delay

6 Timed drying

7 Cycle end

8 Rapid (hold for Key lock)

9 FreshCare+ (hold for Mute)

*Note: some models may have the wording in full instead of the icons.

INDICATORS

Dryness level: Iron dry - Hanger dry - Cupboard dry - Extra dry

Cycle phase: Drying - Cool down - End of cycle.

Empty water tank Clean secondary lter - door - - Clogged lters Autoclean

Refer to Troubleshooting section: Failure call After-sales Service

4 5 6

3’’

These buttons allow you to personalise the selected programme

according to personal requirements. Not all options are available

for all programmes. Some options may be incompatible with

ones you have previously set; if so, you will be alerted by the

buzzer and/or blinking indicators. If the option is available, the

option indicator will stay on. The programme may retain some

options selected in previous drying cycles.

PROGRAMS

Eco cotton kg Max*

This is the most eﬃcient programme in terms of energy

consumption and is suitable for drying normal wet cotton

laundry. The values on the Energy Label are based on this

programme.

NOTE: for optimal energy eﬃciency, select “Cupboard Dry” using

dryness level option. To increase the dryness level, select “Extra Dry”.

Mixed kg 4

This programme is ideal for drying cotton and synthetic

fabrics together.

Bed linen kg Max*

This programme is intended for drying cotton sheets.

Shirts kg 3

This is a programme for Shirts made from cotton or cotton

blend/synthetics.

Sport kg 4

For drying synthetics or cotton sports garments.

Duvet

Programme intended to dry bulky items, such as a single duvet.

Jeans kg 3

For drying sturdy cotton including denim trousers and

jackets.

Easy ironing

This cycle relaxes ﬁbres, thus making ironing and folding

easier. Suitable for small load of damp or dry cotton and cotton

blend fabrics. Not for wet items.

Refresh

A short programme suitable for refreshing ﬁbres and

garments through the emission of fresh air. Do not use on wet

items. It can be used on with any load size but is more eﬀective

with small loads. 20 minutes.

It lasts about

Rapid 30' kg 0.5

Ideal for drying cotton garments spun at high speed in the

washing machine.

Coloured kg Max*

Programme for the gentle drying of coloured fabrics.

Silk kg 0.5

Gentle drying of silk garments.

Wool kg 1

Programme for drying wool clothes. It is advisable to turn the

items inside out before drying. If heavy edges remain damp, leave

them to dry naturally.

Delicates kg 2

For drying delicate laundry requiring gentle treatment.

Synthetics kg 4

For drying synthetic fabrics.

OPTIONS

Dryness level

Press the related button several times to obtain a diﬀerent level

of residual moisture on garments. An indicator signals the level

being selected.

Iron dry: very delicate drying. Items will be more easily

ironed immediately after the cycle.

Hanger dry: a level intended for delicate garments ready to

be hanged.

Cupboard dry: the laundry is ready to be folded and put

away.

Extra dry: for laundry intended to be worn at the end of the

cycle.

Timed drying

This option is to manually set the drying time. Press the

corresponding button to set the required time for drying. An

indicator on the control panel signals the time being selected.

Start delay

This option is for delaying the start of the cycle. Press the

corresponding button several times to ﬁnd the required delay. Once

the max time is reached, the option is reset by pressing the button

again. An indicator on the control panel signals the time being

selected. After pressing the "Start/Pause" button, the machine signals

the time remaining to the start of the cycle. If the door is opened, press

the "Start/Pause" button once the door has been closed.

Rapid

Enables quicker drying.

FreshCare+

If laundry is left inside of the drum once the cycle has

ended, it can be subjected to bacterial proliferation. This

option helps to prevent this from happening by controlling the

temperature and gently rotating the drum. This will continue for up

to 6 hours after the end of the cycle. This setting will remain in the

memory of the previous cycle. If this is used alongside Start Delay,

a crease treatment will be perfomed during this phase by periodic

rotations of the drum.

Key lock

This option makes all machine controls inaccesible, except the

"On/Oﬀ" button. When the machine is on:

• to activate the option, keep the button pressed until the

machines signals that the option has been enabled.

• to disable the option, keep the button pressed until the machine

signals that the option has been disabled.

This option remains in memory if selected in previous drying.

Cycle end

This option activates a prolonged buzzer at the end of the

cycle. Enable it if you are not sure to hear the normal sound at the

end of the cycle. This option remains in memory if selected in the

previous drying.

Mute

This option turns oﬀ all sounds of control panel. Only

warnings remain active.

• to activate the option, keep the button pressed until the indicator

goes on.

• to disable the option, keep the button pressed until the indicator

goes oﬀ.

The duration of these programs will depend on the size of the

load, types of textiles, the spin speed used in your washer and

any extra options selected. In machines equipped with display,

the duration of the cycles is shown on the control panel. The

remaining time is constantly checked and adjusted during the

drying cycle to show the best possible estimate.

Option to use - If all your loads on Automatic Cycles are

consistently less dry or more dry than you would like, you may

increase or decrease the dryness level using the speciﬁc option.

*MAX LOAD 9 Kg (Dry load)

Quick guide

Heat Pump System

The heat pump contains ﬂuorinated greenhouse gases,

contained in a hermetically sealed unit. This sealed unit contains

0.18 kg of the F gas R134a. GWP = 604 (1 t CO).

Power consumption

oﬀ-mode (Po) - Watts 0.50

left-on mode (Pl) - Watts 2.00

Programs MinutesKg kWh

Eco Cotton * 9 2.12 250

Eco Cotton 4.5 1.20 160

Synthetics 4 0.63 90

*This is the reference programme for the energy label and suitable to

dry normal wet cotton laundry. This is the most eﬃcient programme

in terms of energy consumption for drying wet cotton laundry.

(Standard/Default starting conﬁguration).

TRANSPORT AND HANDLING

Never lift the dryer by holding on to its top side.

1. Unplug the dryer.

2. Remove the water from the water tank completely.

3. Make sure that door and water tank are properly closed.

Cleaning the tumble dryer

• The external metal, plastic and rubber parts can be cleaned

with a damp cloth.

• Clean the front air intake grille regularly (every 6 months) with

a vacuum cleaner to remove any lint, ﬂuﬀ or dust deposits.

Furthermore, remove any lint deposits from the ﬁlters area,

using a vacuum cleaner every so often.

• Do not use solvents or abrasives.

CLEANING AND MAINTENANCE

WARNING: unplug the dryer during the cleaning and

maintenance procedures.

Emptying the water tank after each cycle (see Fig. A).

Pull the container out of the dryer and empty it into a sink or

other suitable drain, then place it back properly. Do not use the

dryer without having inserted the container back in place.

Cleaning the primary door lter after each cycle (see Fig. B).

Pull the primary door ﬁlter out and clean it by removing the lint from

the ﬁlter surface under running water or using a vacuum cleaner.

Cleaning the secondary door filter when the relevant

indicator turns on (see Fig. C).

Pull the secondary door ﬁlter out and clean it in all its parts by

washing it under running water or using a vacuum cleaner.

Clogged lters - clean both door lters (see Fig. B, Fig. C).

For optimal performance, dry the lters before inserting them

back in place.

Do not use the dryer without having inserted all lters back

in place properly rst.

The lters are essential parts for drying. They are intended

to collect the lint formed during the drying process. In case

of clogged filters, the air flow inside the dryer would be

seriously aected: the drying time would be longer, the energy

consumption would increase and the dryer could be damaged.

If these procedures are not carried out properly, the dryer may

not start.

NOTE: After cleaning the ﬁlters the relevant indicator remains on;

this is normal, it will disappear when you start a new drying cycle.

Autoclean

The maintenance of the bottom ﬁlter of this model is

automatic. The dryer carries out cleaning when the sensors signal

the need to do so. In this case, the machine goes on working even

when the drying cycle is completed. An indicator on the control

panel will signal the maintenance. Do not switch the machine o

during this phase.

PRODUCT DESCRIPTION

1. Water Tank (A)

2. Air Intake grille

3. Door ﬁlter: primary (B), secondary (C)

B B

Step 1 Step 2 Step 3

Specyfikacje produktu

Marka:	Whirlpool
Kategoria:	Suszarka bębnowa
Model:	FFT M11 9X2BY EE

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Whirlpool FFT M11 9X2BY EE, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Suszarka bębnowa Whirlpool

Whirlpool ST U 93E EU Instrukcja

4 Grudnia 2024

Whirlpool FFT M11 82 SPT Instrukcja

4 Grudnia 2024

Whirlpool FFT CM11 8XB FR Instrukcja

4 Grudnia 2024

Whirlpool FFT M11 8X3B IT Instrukcja

4 Grudnia 2024

Whirlpool FFT M11 9X2BY EE Instrukcja

4 Grudnia 2024

Whirlpool FFT M11 8X3 EE Instrukcja

4 Grudnia 2024

Whirlpool FFT M11 82 IT Instrukcja

4 Grudnia 2024

Whirlpool FFTN M11 82 IT Instrukcja

4 Grudnia 2024

Whirlpool FFT M11 8X3WS IT Instrukcja

4 Grudnia 2024

Whirlpool FFT M11 9X3WSY IT Instrukcja

4 Grudnia 2024

Instrukcje Suszarka bębnowa

Najnowsze instrukcje dla Suszarka bębnowa

Bauknecht TRAD 6267 Instrukcja

4 Grudnia 2024

Bauknecht TRAD 6247 Instrukcja

4 Grudnia 2024

Bauknecht T Soft M11 82 N Instrukcja

4 Grudnia 2024

Exquisit TK810-060 Instrukcja

4 Grudnia 2024

Asko T410HD.W.AU Instrukcja

15 Października 2024

Bosch WTH8300CNL Instrukcja

15 Października 2024

Adler AD 2279 Instrukcja

15 Października 2024

Haier HWD90-B14959NU1 Instrukcja

15 Października 2024

Haier HWD100-B14959S8NU1 Instrukcja

15 Października 2024

Haier HWD100-B14959NU1 Instrukcja

15 Października 2024