Instrukcja obsługi Waring Commercial 7015N


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Waring Commercial 7015N (2 stron) w kategorii mikser. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/2
Blender
Operating anual M
IMPORTANT
HOT BLENDING INSTRUCTIONS
To minimize the possibility of scalding when blending hot materials, the
following precautions and procedures must be observed:
1) If you are using the standard two-piece container lid that originally
came with your blender, limit the amount of material processed to
.1/2 pint
NOTE: A special accessory lid assembly is available for use with
, which allows safe processing ofstainless steel containers only
larger loads.
Order 1-Quart Hot Blending Lid, Catalog No. CAC14.
2) If you are using the standard two-piece container lid, completely
remove the center portion of the lid before turning blender on.This
will allow venting of the rapidly heated and expanding air present
inside container when blender is running.
If you are using the , follow the instructions special accessory lid
packed with the lid; venting will be accomplished automatically.
3) Always start blending on lowest speed setting, then progress to
desire speed.
4) Never stand directly over blender when it is being started or while
running.
SERVICE
Refer to the list of Factory Approved Service Centers enclosed with
your Waring Blender for the name of the nearest Service Center or
Write to:
SERVICE CENTER
314 ELLA T. GRASSO AVENUE
TORRINGTON, CT 06790
(800) 269-6640
Ship Blenders for repair to the above address or to a Factory Approved
Service Center. Do not ship to a Waring Sales Office.
Replacement parts for your own “Out of Warranty” repairs are obtainable
at the above address.
WARING COMMERCIAL
314 Ella T. Grasso Ave.
P.O.Box 3201
Torrington, CT 06790
www.waringproducts.com 014775 RV05 0306
IMPORTANT SAFEGUARDS
When using electrical equipment basic safety precautions should
always be followed including the following:
1. READ ALL INSTRUCTIONS.
2. To protect against electrical hazards do not immerse the Blender
Base in water or other liquid.
3. Close supervision is necessary when any blender is used by or near
children.
4. Unplug from outlet when not in use, before putting on or taking off
parts, and before cleaning.
5. Avoid contacting moving parts.
6. Do not operate your blender with a damaged cord or plug or after the
appliance malfunctions or is dropped or damaged in any manner.
Return appliance to the nearest authorized service facility for
examination, repair or electrical or mechanical adjustment.
7. The use of attachments including canning jars not recommended by
the blender manufacturer may cause a risk of personal injury.
8. Do not use outdoors.
9. Do not let cord hang over edge of table or counter, or touch hot
surfaces.
10. Keep hands and utensils out of container while blending to prevent
the possibility of severe personal injury and/or damage to the
blender. A rubber scraper may be used but must be used only when
the blender is not running.
11. Blades are sharp. Handle carefully.
12. If your blender utilizes a removable Jar Base and Blade Assembly,
to avoid injury never place cutter assembly cutting blades on base
without container properly attached.
13. Always operate blender with cover in place.
14. When blending hot liquids, remove center piece of two-piece cover
on those units supplied with this construction. See Hot Blending
Instructions.
SAVE THESE INSTRUCTIONS
PRESET TIMER BLENDER
SPECIFICATIONS
RATING 3.5A at 120VAC/50HZ (CATALOG NO. 7015)
1.5A at 230VAC/50HZ (CATALOG NO. 8015)
AUTOMATIC Two preset timing intervals (15 seconds and 3 seconds) selectable via
TIMER toggle switch on control panel. Timer can be bypassed for manual
operation
BASE Die cast zinc and steel, baked enamel and chrome finish top.
CONTAINER 48 ounce capacity Lexan polycarbonate jar with stainless steel blade,
two-piece plastic cover.
CORD 6 foot, 18 gauge, three conductor grounded cord with strain relief.
U.L. LISTED 120V models only.
CONTROL PANEL COMPONENTS
MODE SELECTOR SWITCH Three position maintained contact toggle switch
located on right hand side of control panel, labeled AUTO/OFF/MANUAL;
selects desired operating mode.
TIMING SELECTOR SWITCH Three position momentary contact toggle switch,
spring loaded to center position, located on left hand side of control panel,
labeled 15 SEC/3 SEC; selects desired timing interval.
INDICATOR LAMP Neon pilot light; indicates when mode selector switch is in
either AUTO or MANUAL position.
OPERATION INSTRUCTIONS
1. Be sure mode selector switch is in the OFF (center) position.
2. Plug power cord into properly wired and grounded outlet.
3. For AUTOMATIC operation:
• Set mode selector switch to AUTO position. Indicator lamp will light.
• Momentarily move timing selector switch to position for time cycle desired.
Motor will run for interval selected, and stop automatically.
NOTE: Override of the automatic stop can be obtained by holding the timing selector
switch in position beyond the end of the preset interval. Motor will continue to run
until switch is released.
• When finished blending, return mode selector switch to OFF position. Indicator lamp
will extinguish.
4. For MANUAL operation:
• Set mode selector switch to MANUAL position. Indicator lamp will light, and motor
will run continuously.
• When finished blending, return mode selector switch to OFF position. Motor will stop
and indicator lamp will extinguish.
5. Unplug power cord from outlet when blender is not in use, before putting on or taking
off any parts other than container, and before cleaning.


Specyfikacje produktu

Marka: Waring Commercial
Kategoria: mikser
Model: 7015N

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Waring Commercial 7015N, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje mikser Waring Commercial

Instrukcje mikser

Najnowsze instrukcje dla mikser

Wilfa

Wilfa 2Go XL TG1B-900 Instrukcja

15 Października 2024
Bosch

Bosch ErgoMixx MSM6S90B Instrukcja

14 Października 2024
Bamix

Bamix Mono Instrukcja

11 Października 2024
Scarlett

Scarlett SC-HB42F80 Instrukcja

11 Października 2024
Kenwood

Kenwood CL639 Instrukcja

10 Października 2024
Orbegozo

Orbegozo LI 5060 Instrukcja

10 Października 2024
Orbegozo

Orbegozo BV 9800 Instrukcja

9 Października 2024