Instrukcja obsługi Vimar 01875.120


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Vimar 01875.120 (6 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 10 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/6
Fig. 1. Schema collegamenti alimentatore 01875.120 con regolatore master universale.
Attenzione: I moduli LED devono essere connessi soltanto in serie.
L’alimentatore elettronico dimmerabile può essere controllato anche tramite un interruttore col-
legato tra fase e sincronismo (Fig. 2). In questo caso sapossibile eseguire solo l’ON/OFF alla
massima intensità del modulo LED collegato all’alimentatore.
Fig. 2. Schema collegamenti alimentatore 01875.120 con interruttore ON/OFF.
Prima di collegare l’alimentatore alla rete di alimentazione 120 V~, selezionare la corrente nomi-
nale di uscita 350/500/700 mA mediante il jumper collocato sul lato secondario e collegare il
modulo/striscia LED (Fig. 3)
.
Fig. 3. Posizione del jumper per selezionare la corrente di uscita 350 mA.
REGOLE DI INSTALLAZIONE
L’installazione deve essere effettuata con l’osservanza delle disposizioni regolanti l’installazione
del materiale elettrico in vigore nel paese dove i prodotti sono installati. Garantire delle distanze
minime attorno all’apparecchio in modo che vi sia una sufficiente ventilazione.
L’apparecchio non deve essere sottoposto a stillicidio o a spruzzi d’acqua.
Fig. 4. Distanze minime tra l’alimentatore 01875.120 e le luminarie e/o pareti esterne.
CONFORMITÀ NORMATIVA
Direttiva BT.
Norme EN 61347-2-13, EN 62384.
Viale Vicenza, 14 - I 36063 Marostica VI
Tel. +39 0424 488 600 - Fax (Italia) +39 0424 488 188 - Fax (Export) +39 0424 488 709
www.vimar.com
49400638A0 01 1309
VIMAR - Marostica - Italy
01875.120
Alimentatore elettronico 120 V~ 60 Hz con uscita multicorrente per lampade a
LED dimmerabili 350/500/700 mA, dimmerabile con regolatori MASTER univer-
sali. Uscita SELV equivalent.
CARATTERISTICHE
• Adatto per moduli/strisce LED SELV equivalenti: 350/500/700 mA
Tensione di alimentazione: 120 V~ 60 Hz
Assorbimento a 120 V~:
- 185 mA (uscita 15 W, 350 mA, 3-45 V max)
- 245 mA (uscita 22 W, 500 mA, 3-46 V max)
- 300 mA (uscita 27 W, 700 mA, 3-40 V max)
• Morsetti:
- 2 per alimentazione (L fase, N neutro)
- 1 per sincronismo (S)
- 2 per uscita modulo led (+, -)
• Fusibile 1 A incorporato ad alta capacità di rottura
Ponticelli per selezionare la corrente di uscita
Corrente nominale di uscita: 350/500/700 mA ± 10%
Tensione di uscita massima: 50 V
Massimo carico: 15 W a 350 mA/22 W a 500 mA/27 W a 700 mA
PFC attivo:
- Power factor = 0,88 (15 W, 350 mA)
- Power factor = 0,92 (22 W, 500 mA)
- Power factor = 0,94 (27 W, 700 mA)
Potenza massima dissipata: 4 W a 350 mA, 5 W a 500 mA, 6 W a 700 mA
Rendimento η a 120 V~:
- 77% (15 W, 350 mA)
- 81% (22 W, 500 mA)
- 81% (27 W, 700 mA)
• Consumo in standby: < 0.5 W
Temperatura di funzionamento ta: -5°C - +45°C (da interno)
Apparecchio di classe II
• Max numero di Alimentatori:
- con interruttore magnetotermico C10: max 7;
- con Interruttore magnetotermico C16: max 12.
Alimentatore da incorporare IP20 per uso interno
Isolamento galvanico tra primario e secondario: 4 kVrms
Alimentatore regolabile:
- con regolatore master universale Vimar configurato con taglio di fase LE (art. 20135.120/191
35.10/16559.120/14135.120, art. 20136.120/19136.120/16603.120/14136.120). Comando
ON/OFF e regolazione della luminosità da 0 a 100% (consultare i fogli di istruzione dei regola-
tori master 1M universale basculante e rotativo con pulsante incorporato). Non collegare con
tradizionale regolatore a taglio di fase
- con interruttore on/off tra fase e sincronismo. Comando ON/OFF ad intensità 100% del
power/modulo LED
Max 10 alimentatori collegabili ad un unico regolatore master
Lunghezza del cavo dal regolatore master/interruttore all’ultimo alimentatore: max 100 m
Lunghezza del cavo per i moduli led: 10 m con cavi sezione 1,5 mm
2
Morsetti di entrata e uscita contrapposti
Sezione cavi:
- Primario: 0,75 mm2 1,5 mm2 (cavi rigidi); 0,75 mm21 mm2 (cavi flessibili)
- Secondario (terminali LED): 0,5 mm2 1,5 mm2 (cavi rigidi); 0,5 mm2 1 mm2 (cavi flessibili)
Serracavo su primario e secondario per cavi di diametro:
- Primario: min 4 mm- max 8 mm;
- Secondario: min 4 mm- max 8 mm.
Fissaggio dell’alimentatore tramite viti
Protezioni: Termica (auto-off reversibile), Cortocircuito, Sovraccarichi
Max. temperatura dell’involucro tc: 80°C
Dimensioni (l x w x h): 224 mm x 60 mm x 36 mm
COLLEGAMENTI
Per tutti i dettagli sulle possibili architetture di installazione si veda SI-Schemi Installativi
presente su www.vimar.com -> Prodotti -> Catalogo prodotti in corrispondenza del codice
articolo.
L’installazione tipica dell’alimentatore prevede l’utilizzo del regolatore master universale stand-
alone Vimar nella configurazione descritta in Fig. 1.
I regolatori master stand-alone Vimar utilizzabili per il controllo dell’alimentatore 01875.120 sono:
Regolatore master 1M basculante universale: art. 20135.120-19135.120-16559.120-
14135.120;
Regolatore master 1M rotativo universale + pulsante: art. 20136.120-19136.120-16603.120-
14136.120.
Il collegamento deve avvenire in associazione ad un portafusibile con fusibile rapido ad alto
potere di interruzuione tipo F2,5AH250V.
L
L
N
S
N
01875.120
L
S
N
B
A
A
A 25 ; B 100 mm mm
Ta: 45°C max
01875.120 01875.120
Moduli LED/
Strisce LED
20416
19416
16460
14416
20135.120-20136.120
19135.120-19136.120
16559.120-16603.120
14135.120-14136.120
01875.120
20008
19008
16080
14008
L
L
L
S
N
N
P
N
L
S
N
120
Moduli LED/Strisce LED
700 mA
500 mA
+
-
350 mA
Per impostare a 350 mA la corrente nominale
di uscita, posizionare il jumper come da figura.
In generale, per impostare la corrente di uscita
nominale desiderata, posizionare il jumper in
corrispondenza della rispettiva dicitura.
Interruttore
Moduli LED/Strisce LED
Morsetti di uscita modulo/striscia LED
Viale Vicenza, 14 - I 36063 Marostica VI
Tel. +39 0424 488 600 - Fax (Italia) +39 0424 488 188 - Fax (Export) +39 0424 488 709
www.vimar.com
01875.120
Multicurrent supply unit, 120 V~ 60 Hz, for 350/500/700 mA LED lamps, control-
lable with multiload MASTER dimmers.
CHARACTERISTICS
• Suited for power/equivalent LED SELV modules: 350/500/700 mA
Supply voltage: 120 V~ 60 Hz
: Absorption at 120 V~
- 185 mA (output 15 W, 350 mA, 3-45 V max);
- 245 mA (output 22 W, 500 mA, 3-46 V max);
- 300 mA (output 27 W, 700 mA, 3-40 V max).
Terminals:
- 2 for power supply (L phase, N neutral)
- 1 for synchronism (S)
- 2 for led module output (+, -)
• Fuse with high breaking capacity type 1 A incorporated
• Jumpers for selecting the output current
• Rated output current: 350/500/700 mA ± 10%
• Max. output voltage: 50 V
• Maximum load: 15 W    350 mA/ 22 W 500 mA/ 27 W 700 mA
• PFC active:
- Power factor = 0,88 (15 W, 350 mA);
- Power factor = 0,92 (22 W, 500 mA);
- Power factor = 0,94 (27 W, 700 mA).
• Max. dissipated power: 5 W    350 mA/ 5.5 W 500 mA/ 6.5 W 700 mA
120 V~: Yield η
- 77% (15 W, 350 mA);
- 81% (22 W, 500 mA);
- 81% (27 W, 700 mA).
• Consumption in standby: < 0.5 W
• Operating temperature ta: -5 °C - +45 °C (indoor)
Appliances of class II
Max number of Power supplies:
- with circuit breaker C10: max 7;
- with circuit breaker C16: max 12.
Power supply for incorporation IP20 for internal use;
Galvanic isolation between primary and secondary: 4 kVrms;
Adjustable dimmer:
- with Vimar universal master dimmer configured for Leading Edge (art. 20135.120/19135.120/16
559.120/14135.120 - art. 20136.120/19136.120/16603.120/14136.120). ON/OFF and brightness
adjustment from 0 to 100% (consult the instructions of the 1M rocker and rotary universal master
dimmer with incorporated button). Do not connect to a conventional phase cutter dimmer.
- with on/off switch between the phase and dimmered input. ON/OFF control at 100% brightnes
of the power/LED module
Max 10 power supplies connected to a single master dimmer (see also max number of power
supplies with circuit breaker)
Cable length from master dimmer/switch to last power supply: max 100 m
Cable length for led modules: 10 m with cables section 1.5 mm
2
Supplied with terminal protection and cable clamps
Opposite input and output terminals
Cable section:
- Primary: 0,75 mm21,5 mm2 (rigid cables); 0,75 mm2 – 1 mm2 (flexible cables)
- Secondary (LED terminals): 0,5 mm
2 – 1,5 mm2 (rigid cables); 0,5 mm2 – 1 mm2 (flexible cables)
Cable clamp on primary and secondary for cable diameters:
- Primary: min 4 mm- max 8 mm
- Secondary: min 4 mm- max 8 mm
Screw fixing for power supply
Protections: Thermal (auto-off reversible), Short circuit, Overloads
Max. temperature of tc case: 80 °C
Size (l x w x h): 224 mm x 60 mm x 36 mm
CONNECTIONS
For all details on possible installation architectures, please refer to SI-Connection diagrams
for the relevant item code at www.vimar.com -> Products -> Product catalogue.
The typical power supply installation requires the use of the stand-alone Vimar universal
master dimmer in the configuration described in fig. 1.
The stand-alone Vimar master dimmers which can be used to control the 01875.120 are:
1M universal rocker master dimmer: art. 20135.120-19135.120-16559.120-14135.120;
1M universal rotary master dimmer + button: art. 20136.120-19136.120-16603.120-
14136.120;
• The dimmer connection should be made together with a fuse carrier with a fuse with a high breaking
capacity type F2.5AH250V as shown in the diagrams.
Fig. 1. Diagram of LED 350/500/700 mA dimmerable electronic power supply + universal master dimmer
! Important: With the art. 01875.120 the LED modules must be connected only in series.
The LED dimmerable electronic power supply can also be controlled by a switch between the
phase and the controlled input (fig. 2). In this case it is only possible to switch ON/OFF at maxi-
mum brightness of the LED module connected to the power supply.
Fig. 2. Diagram of LED 350/500/700 mA dimmerable electronic power supply + ON/OFF switch connections.
Select the rated output current 350/500/700 mA using the jumpers on the secondary side before
connecting the power supply to the mains 120V~.
Fig. 3. Position of the jumpers for selecting the output current 350 mA
INSTALLATION RULES
Installation should be carried out in compliance with the current regulations regarding the installation of
electrical systems in the country where the products are installed. Ensure clearance around the applian-
ce so there is sufficient ventilation. There must be no dripping or splashes of water on the appliance.
Fig. 4. Minimum clearance between the LED 350/500/700 mA dimmerable electronic power supply
and the lights and/or external walls.
STANDARD COMPLIANCE
LV directive
Standards EN 61347-2-13, EN 62384.
B
A
A
A 25 ; B 100 mm mm
Ta: 45°C max
01875.120 01875.120
LED module/ LED strip
Switch
To set at 350 mA nominal current output, set the
jumper as shown.
In general, to set the rated output current desi-
red, place the jumper at the respective term.
LED module/
LED Strip
20416
19416
16460
14416
20135.120-20136.120
19135.120-19136.120
16559.120-16603.120
14135.120-14136.120
01875.120
20008
19008
16080
14008
L
L
L
S
N
N
P
N
L
S
N
120
L
L
N
S
N
01875.120
L
S
N
LED module/ LED strip
700 mA
500 mA
+
-
350 mA
LED module/strip output terminals
Fig. 1. Schéma de branchement de l’alimentation 01875.120 + variateur maître universel.
! Attention: Avec art. 01875.120 les modules LED doivent être connectés exclusivement en série
L’alimentation électronique variable peut également être commandée par un interrupteur entre la
phase et l’entrée pilotée (fig. 2). Dans ce cas, l’ON/OFF n’est possible qu’à l’intensité maximale
du module LED relié à l’alimentation.
Fig. 2. 1 Schéma de branchement de l’alimentation 01875.120 + variateur maître universel.
Sélectionner le courant nominal de sortie 350/500/700 mA avec les cavaliers côté secondaire
avant de brancher l’alimentation au réseau d’électricité 120 V~.
Fig. 3. Position des cavaliers pour sélection de la courant de sortie 350 mA.
GLES D’INSTALLATION
Le circuit doit être réalisé conformément aux dispositions qui régissent l’installation du matériel
électrique en vigueur dans le pays concerné. Respecter les distances minimales autour de l’ap-
pareil pour conserver une ventilation suffisante.
L’appareil ne doit pas être exposé à des suintements ou des éclaboussures.
Fig. 4. Distances minimales entre lalimentation 01875.120 et les luminaires et/ou les cloisons extérieures.
CONFORMITÉ AUX NORMES
Directive BT. Normes EN 61347-2-13, EN 62384.
L
L
N
S
N
01875.120
L
S
N
20416
19416
16460
14416
20135.120-20136.120
19135.120-19136.120
16559.120-16603.120
14135.120-14136.120
01875.120
20008
19008
16080
14008
L
L
L
S
N
N
P
N
L
S
N
120
Viale Vicenza, 14 - I 36063 Marostica VI
Tel. +39 0424 488 600 - Fax (Italia) +39 0424 488 188 - Fax (Export) +39 0424 488 709
www.vimar.com
Alimentateur 120 V~ 60 Hz multicourant pour lampes à LED 350/500/700 mA,
réglage avec variateurs MASTER multicharge.
CARACTÉRISTIQUES
Tension d’alimentation : 120 V~ 60 Hz
Pour modules LED RGB SELV : 350/500/700 mA
V~: Absorption à 120
- 185 mA (sortie 15 W, 350 mA, 3-45 V max)
- 245 mA (sortie 22 W, 500 mA, 3-46 V max)
- 300 mA (sortie 27 W, 700 mA, 3-40 V max)
• Bornes :
- 2 pour alimentation (L phase, N neutre)
- 1 pour synchronisme (S )
- 2 pour sortie module led (+, -)
• Fusible à haut pouvoir de coupure 1 A intégré
• Cavaliers pour sélection du courant de sortie
• Courant nominal de sortie 350/500/700 mA ± 10%
• Tension maximale de sortie : 50 V
: 15 W Charge maximale    350 mA/ 22 W 500 mA/ 27 W 700 mA
: PFC actif
- Power factor = 0,88 (15 W, 350 mA);
- Power factor = 0,92 (22 W, 500 mA);
- Power factor = 0,94 (17 W, 700 mA).
: 5 W Puissance maximale dissipée    350 mA/ 5,5 W 500 mA/ 6,5 W 700 mA
120 V~:Rendement η
- 77% (15 W, 350 mA);
- 81% (22 W, 500 mA);
- 81% (27 W, 700 mA).
• Consommation en standby: < 0,5 W
Température de fonctionnement: - 5° C - + 45° C (intérieur)
Appareil de classe II
Nombre max d’alimentations
- avec interrupteur magnétothermique C10: max 7
- avec interrupteur magnétothermique C16: max 12
Alimentation pour intérieur IP20
Isolation galvanique entre le primaire et le secondaire: 4 kVrms
Alimentation réglable par:
- variateur maître universel Vimar configuré en mode coupure de phase LE (art. 20135.120/
19135.120/16559.120/14135.120-art.20136.120/19136.120/16603.120/14136.120).
Commande ON/OFF et réglage de l’intensité lumineuse entre 0 et 100 % (voir notice d’in-
structions pour variateurs maîtres 1M universels à bascule et rotatifs avec bouton intégré). Ne
pas connecter à un variateur classique à coupure de phase
- à un interrupteur on/off entre la phase et l’entrée pilotée. Commande ON/OFF intensité 100
% du module LED
Max 10 alimentations reliées au même variateur maître (voir aussi le nombre maximal d’alimen-
tations avec interrupteur magnétothermique)
Longueur du câble entre le variateur maître/l’interrupteur et la dernière alimentation : max 100 m
Longueur du câble pour les modules led: 10 m avec câbles section 1,5 mm
2
Livré avec cache-bornes et serre-câbles
Bornes d’entrée et de sortie opposées
Section des câbles
Primaire: 0,75 mm
2 – 1,5 mm2 (câbles rigides); 0,75 mm2 – 1 mm2 (câbles flexibles)
Secondaire (terminaux LED RGB): 0,5 mm
21,5 mm2 (câbles rigides); 0,5 mm21 mm2 (câbles
flexibles)
Serre-câble sur primaire et secondaire pour diamètres de câble suivants:
- Primaire : min 4 mm - max 8 mm
- Secondaire : min 4 mm - max 8 mm
Fixation de l’alimentation par vis
Protections: thermique (auto-off réversible), court-circuit, surcharges
Température max. du boîtier plastique: 80° C
Dimensions (l x w x h): 224 mm x 60 mm x 36 mm
BRANCHEMENTS
Pour plus de détails sur les architectures possibles de l’installation, voir SI-Diagrams de
connexion sur le site www.vimar.com -> Produits -> Catalogue produits et code de l’article.
Linstallation classique de l’alimentation comprend un variateur maître universel stand-alone
Vimar dans la configuration crite fig. 1.
Les variateurs maîtres stand-alone Vimar permettant de commander l’alimentation électroni-
que 01875.120 sont les suivants.
Variateur maître 1M à bascule universel: art. 20135.120-19135.120-16559.120-14135.120;
Variateur maître 1M rotatif universel + bouton: art. 20136.120-19136.120-16603.120-
14136.120;
Brancher le variateur à un porte-fusible avec fusible à haut pouvoir de coupure F2,5AH250V,
voir schémas.
01875.120
Module LED/Bande de LED
Interrupteur
Module LED/Bande de LED
De fixer à 350 mA de courant de sortie nominale,
régler le cavalier comme indiqué.
En général, pour régler le courant nominal de
sortie désiré, placez le cavalier sur la durée
respective.
B
A
A
A 25 ; B 100 mm mm
Ta: 45°C max
01875.120 01875.120
Module LED/
Bande de LED
700 mA
500 mA
+
-
350 mA
Bornes de sortie module/ruban LED


Specyfikacje produktu

Marka: Vimar
Kategoria: Niesklasyfikowane
Model: 01875.120

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Vimar 01875.120, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Niesklasyfikowane Vimar

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane