Instrukcja obsługi Victron Energy Phoenix Inverter


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Victron Energy Phoenix Inverter (152 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/152
Manual
EN
Handleiding
NL
Manuel
FR
Anleitung
DE
Manual
ES
Användarhandbok
SE
Manuale
IT
Appendix
Phoenix Inverter (with firmware xxxx400 or higher)
12 | 3000 | 230V 24 | 3000 | 230V 48 | 3000 | 230V
24 | 5000 | 230V 48 | 5000 | 230V
2
3
EN ES SE A NL FR DE IT ppendix
1. SAFETY INSTRUCTIONS
In general
Please read the documentation supplied with this product first, so that you are familiar
with the safety signs en directions before using the product.
This product is designed and tested in accordance with international standards. The
equipment should be used for the designated application only.
WARNING: DANGER OF ELECTRICAL SHOCK
The product is used in combination with a permanent energy source (battery). Even if
the equipment is switched off, a dangerous electrical voltage can occur at the input
and/or output terminals. Always switch the AC power off and disconnect the battery
before performing maintenance.
The product contains no internal user serviceable parts. Do not remove the front panel -
and do not put the product into operation unless all panels are fitted. All maintenance
should be performed by qualified personnel.
Never use the product at sites where gas or dust explosions could occur. Refer to the
specifications provided by the manufacturer of the battery to ensure that the battery is
suitable for use with this product. The battery manufacturer's safety instructions
should always be observed.
WARNING: do not lift heavy objects unassisted.
Installation
Read the installation instructions before commencing installation activities.
This product is a safety class I device (supplied with a ground terminal for safety
purposes). The chassis must be grounded. A grounding point is located on the
outside of the product. If it can be assumed that the grounding protection is damaged,
the product should be taken out of operation and prevented from accidentally being
put into operation again; contact qualified maintenance personnel.
Ensure that the connection cables are provided with fuses and circuit breakers. Never
replace a protective device by a component of a different type. Refer to the manual for
the correct part.
Check before switching the device on whether the availab le voltage source conforms
to the configuration settings of the product as described in the manual.
Ensure that the equipment is used under the correct operating conditions. Never
operate it in a wet or dusty environment.
Ensure that there is always sufficient free space around the product for ventilation,
and that ventilation openings are not blocked.
6
3. OPERATION
3.1 On/Off Switch
When switched to "on", the product is fully functional. The inverter will come into
operation and the LED "inverter on" will light up.
3.2 Remote control
Remote control is possible with a simple on/off switch or with a Phoenix Inverter
Control panel.
3.3 LED Indications
LED off
LED flashes
LED illuminated
Inverter
The inverter is on and supplies
power to the load.
on
inverter on
overload
low battery
off
temperature
The nominal output of the inverter is
exceeded. The “overload” LED
flashes.
on
inverter on
overload
low battery
off
temperature
7
EN ES SE A NL FR DE IT ppendix
The inverter is switched off due to
overload or short circuit.
on
inverter on
overload
low battery
off
temperature
The battery is almost fully
exhausted.
on
inverter on
overload
low battery
off
temperature
The inverter has switched off due to
low battery voltage.
on
inverter on
overload
low battery
off
temperature
The internal temperature is reaching
a critical level.
on
inverter on
overload
low battery
off
temperature
8
The inverter has switched off due to
the electronics temperature being
too high.
on
inverter on
overload
low battery
off
temperature
-If the LEDs are flashing alternately,
the battery is nearly exhausted and
the nominal output is exceeded.
-If "overload" and "low battery" flash
simultaneously, the ripple voltage on
the battery terminals is too high.
on
inverter on
overload
low battery
off
temperature
The inverter switched off due to
excess ripple voltage on the battery
terminals.
on
inverter on
overload
low battery
off
temperature
For the and up date latest most to information
about the blink codes, please refer to the
Victron Toolkit app.
Click on or scan the QR code to get to the
Victron Support and Downloads/Software page.
4
3. BEDIENING
3.1 On/Off schakelaar
Wanneer de schakelaar op “on” wordt geschakeld werkt het apparaat volledig.
De omvormer zal inschakelen en de LED “inverter on” zal gaan branden.
3.2 Afstandsbediening
Afstandsbediening is mogelijk met een simpele aan/uit schakelaar of met een Phoenix
Inverter Control paneel.
3.3 LED Indications
LED uit
LED knippert
LED brandt
Inverter
De omvormer staat aan en levert
vermogen aan de belasting.
on
inverter on
overload
low battery
off
temperature
Het nominale vermogen van de
omvormer wordt overschreden.
on
inverter on
overload
low battery
off
temperature


Specyfikacje produktu

Marka: Victron Energy
Kategoria: Niesklasyfikowane
Model: Phoenix Inverter

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Victron Energy Phoenix Inverter, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Niesklasyfikowane Victron Energy

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

SmallRig

SmallRig VB99 SE Instrukcja

29 Stycznia 2025
QSC

QSC TSC-8 Instrukcja

29 Stycznia 2025
XTRARM

XTRARM XTR-FS5130 Instrukcja

29 Stycznia 2025
Sunding

Sunding SD-581G Instrukcja

29 Stycznia 2025
XTRARM

XTRARM XTR-FS5070 Instrukcja

29 Stycznia 2025
XTRARM

XTRARM XTR-FS2010 Instrukcja

29 Stycznia 2025
OSEE

OSEE TX402 Instrukcja

29 Stycznia 2025