Instrukcja obsługi Velleman WS1070

Velleman Stacja pogodowa WS1070

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Velleman WS1070 (32 stron) w kategorii Stacja pogodowa. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/32
W
S1070
WIRELESS WEATHER STATION + DCF CLOCK AND OUTDOOR SENSOR
DRAADLOOS WEERSTATION + DCF-KLOK EN BUITENSENSOR
STATION MÉTÉO SANS FIL + HORLOGE DCF ET CAPTEUR EXTÉRIEUR
ESTACIÓN METEOROLÓGICA INALÁMBRICA CON RELOJ DCF Y SENSOR EXTERIOR
DRAHTLOSE WETTERSTATION MIT DCF-UHR UND AUßENSENSOR
USER MANUAL
GEBRUIKERSHANDLEIDING
NOTICE D’EMPLOI
MANUAL DEL USUARIO
BEDIENUNGSANLEITUNG
WS1070_v4 VELLEMAN 2
WS1070 – WIRELESS WEATHER STATION + DCF CLOCK AND OUTDOOR SENSOR
1. Introduction & Features
To all residents of the European Union
Important environmental information about this product
This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm
the environment.
Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be taken to a specialized
company for recycling.
This device should be returned to your distributor or to a local recycling service.
Respect the local environmental rules.
If in doubt, contact your local waste disposal authorities.
Thank you for buying the WS1070! This is a wireless weather station with DCF clock and outdoor sensor. Please read
the manual thoroughly before bringing this device into service. If the device was damaged in transit, don't install or use it
and contact your dealer. Note that damage caused by disregard of certain guidelines in this manual is not covered by
the warranty and the dealer will not accept responsibility for any ensuing defects or problems. Contents: 1 x base
station, 1 x remote outdoor sensor (including a thermo-hygro, rain and wind sensor), 2 x adjustable hoops, 2 plastic
arms and this manual.
2. Setting up Your Weather Station
• Open the housing of the remote sensor to reveal the two sockets (wind and rain sensor).
• Connect the cables of the wind and the rain sensor to the corresponding sockets.
• Open the battery compartment of the outdoor sensor and insert 2 x AA alkaline batteries. Mind the polarity.
• Open the battery compartment of the weather station and insert 3 x AA alkaline batteries. Mind the polarity.
Every time the outdoor sensor is powered up (after e.g. a battery replacement), the LED indicator will light for 4
seconds (if no LED lights, make sure the batteries are correctly inserted). The sensor will transmit data every 24
seconds after which it will start radio-controlled time reception. After the RCC time reception (± 5 minutes) no
data will be transmitted. The LED will blink 5x once the RCC signal is synchronized. Regular RF link will be
established once the RCC reception routine is finished.
When the weather station is powered up, a short beep will sound and all LCD segments will light for 3 seconds
before the station enters into the learning mode.
Do not press any key during the learning period (± 10 minutes). After both indoor and outdoor data is
displayed you can install the remote outdoor sensor and set the time (if no RCC reception is available). If there is
no temperature reading on the outdoor station make sure both units are within transmission range or check the
batteries. If you press a key before the weather station receives the temperature signal, take out the batteries and
reinstall them after ± 10 seconds.
Time and date are provided by a highly accurate atomic clock. Note that, whenever reception is possible, the
weather station will scan for the DCF radio signal and overwrite a manually set time and date.
3. Mounting the Units
a. The Base Station
Place the base station onto a flat surf the back of the unit. The unit can ace by deploying the foldable legs at
also be wall-mounted. It is important to check that the radio signal can be received before permanently
mounting both units.
WS1070_v4 VELLEMAN 3
b. The Outdoor Station
To achieve accurate results, the mast must be securely mounted onto a horizontal surface and in an open
area away from trees or other shelters. Check that the anemometer can rotate freely and that the wind can
reach the meter from all sides. Mount the sensors according to the pictures.
• The Wind Sensor (fig. 1)
• The Rain Sensor (fig. 2)
• The Thermo-Hygro Sensor (fig. 3)

Specyfikacje produktu

Marka: Velleman
Kategoria: Stacja pogodowa
Model: WS1070

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Velleman WS1070, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Stacja pogodowa Velleman

Velleman

Velleman WS8707 Instrukcja

14 Września 2024
Velleman

Velleman WS8737 Instrukcja

5 Września 2024
Velleman

Velleman DVM8010 Instrukcja

4 Września 2024
Velleman

Velleman WS8472 Instrukcja

3 Września 2024
Velleman

Velleman WS9245 Instrukcja

3 Września 2024
Velleman

Velleman WS1060 Instrukcja

27 Sierpnia 2024
Velleman

Velleman WS2801 Instrukcja

25 Sierpnia 2024
Velleman

Velleman WS3080 Instrukcja

23 Sierpnia 2024
Velleman

Velleman DVM8020 Instrukcja

22 Sierpnia 2024
Velleman

Velleman WS8471 Instrukcja

20 Sierpnia 2024

Instrukcje Stacja pogodowa

Najnowsze instrukcje dla Stacja pogodowa

Ascot

Ascot GT-WS-07s Instrukcja

15 Stycznia 2025
Ventus

Ventus K0382 Instrukcja

14 Stycznia 2025
TFA

TFA 20.1082.17 Instrukcja

12 Stycznia 2025
Oregon Scientific

Oregon Scientific BAR310HG Instrukcja

12 Stycznia 2025
Auriol

Auriol AHFL 433 B2 Instrukcja

12 Stycznia 2025
Oregon Scientific

Oregon Scientific BAR 898 Instrukcja

11 Stycznia 2025
Davis

Davis Weatherlink Touch Console Instrukcja

11 Stycznia 2025
Taylor

Taylor 5156 Instrukcja

8 Stycznia 2025
La Crosse Technology

La Crosse Technology M71633 Instrukcja

8 Stycznia 2025
La Crosse Technology

La Crosse Technology V41CA Instrukcja

8 Stycznia 2025