Instrukcja obsługi UPM DT523H

UPM przełącznik DT523H

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla UPM DT523H (1 stron) w kategorii przełącznik. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/1

INTRODUCTION

The DT523 is a dusk to dawn timer. This heavy duty outdoor timer is ideal for use with 2

or 3-prong plug-in devices, such as security lighting, seasonal lighting, patio lighting and

other devices you would operate at night.

It can be set to operate in one of three modes:

1) Continuously on from Dusk till Dawn

2) On at night limited by a program

3) Manually switched on

For more information on:

Dusk to Dawn function see page 4

Setting the Clock see page 5

Programming see page 6

Manual function see page 4

Technical specifications see page 9

Warranty see page 9

MANUAL ON/OFF (OVERRIDE)

Press and hold MODE for 3 seconds to manually turn the device ON or OFF.

(ON/OFF icon will flash as indication in override mode).Selecting on/off manually

will temporarily interrupt the dusk to dawn function.

For example, if you manually turn on the light in the middle of the day it will stay

on until the first of the following occurs:

- Dawn the next day

- It encounters the programmed off time

- You manually turn it off again

21 3 4

PROGRAMMING: OFF TIME

Once the ON TIME programming is completed, you may advance

to the OFF TIME. Ensure that you have confirmed all ON TIME settings

(by pressing SET); check that no icons are flashing on the LCD screen:

1) Press (until displays)(see Program Diagram)MODE PRG OFF

2) Press to begin programming the (the hour will flash)SET OFF TIME

3) Press to scroll to the correct hourMODE

4) Press (the minutes will flash)SET

3) Press to scroll to the correct minuteMODE

4) Press (to finish the off time)SET

(In the Program Diagram, the OFF TIME is set to 5:00 am)

To end the program mode, press to return to the regular clock mode. MODE

If no key is pressed for 8 seconds the display will automatically return to the

CLOCK display.

PROGRAMMING: ON TIME

To learn how to set any program, use the Program Diagram as a reference:

Daily Program / ON TIME - 8:15pm / OFF TIME - 5:00am

1) Press (until displays)MODE PRG ON

2) Press to begin programming the (the hour will flash)SET ON TIME

3) Press to scroll to the correct hourMODE

4) Press (the minutes will flash)SET

3) Press to scroll to the correct minuteMODE

4) Press (to finish the )SET ON TIME

(In the Program Diagram, the is set to 8:15 pm)ON TIME

Program Diagram

PROGRAM

OFF TIME

PROGRAM

ON TIME

76 8 9

PROGRAMMING

By setting a program you limit the time the power can go occur between certain

hours. To do this you must first set the clock and then enter the time you would

like it to go on and the time you would like it to go off. The power will be turned on

if it is dark and it is between the on and off time settings. The power will be turned

off when the off time is reached or when it is light again (which ever comes first)

For example if you set an on time of 6 pm and an off time of 9 pm and the sun

sets at 5 pm and rises at 6 am then the light will go on at 6pm and turn off at 9pm.

However if you are using the same six to nine program and the sun does not set

until 7:30 pm the timer will wait until dark to turn on (at 7:30 pm) and then off at 9

pm.

Please note that in the event of a power failure or if the on and off times are

identical the timer will go back to operating as a dawn to dusk timer.

See the following example of program setting on pages 7 and 8.

Outdoor Dusk to Dawn Timer

with one daily program

DT523H

OWNER’S

MANUAL

This heavy duty outdoor

timer is ideal for use with

security lighting, seasonal

lighting, or patio/pond

lighting. Please take

the time to read and

understand this manual to

enjoy the benefits of this

product.

FEATURES

= Clock display

= 1 program (daily)

= Photocell light sensor

=Dusk to dawn mode;

activated by darkness

= Manual on/off override

= Heavy duty design

= Weather resistant

housing

= Standard 3-prong outlet

MODE

LCD

DISPLAY

PHOTOCELL

SET

BUTTONS / LCD DISPLAY

Buttons / features:

LCD display

!LCD: displays the time and program settings (1 program daily)

!PHOTOCELL: environmental light sensor; activates the timer in darkness

(in dusk to dawn mode)

!MODE: changes from clock to program mode

!SET: confirms settings

CLOCK MODE

PROGRAM MODE

OFF TIME

ON TIME

TIME: HOUR MINUTE

PM INDICATOR (12 or 24 hour clock)

TECHNICAL SPECIFICATIONS

Ratings: 120V AC,15A, 60Hz

Max Load : 1,800W resistive, 15FLA, 1.0HP, 15A inductive, 1000W tungsten

Switching Action: Type 1B

Control Pollution Situation: Pollution degree 2

Rated Impulse Voltage: 1500V

* This programmable timer comes with built-in memory backup protection. In the event of

a power outage, all program and clock settings will remain in memory.

Note: If the LCD appears blank it may indicate that the electric circuit has been disconnected.

Double check that the power cords are securely attached to the timer.

Warning: For outdoor installation, mount the time at least three feet above the ground (with the

receptacle plug facing down) to avoid a shock hazard.

1 YEAR WARRANTY

This product carries a one (1) year replacement warranty against defects in

workmanship and materials. This product is not guaranteed against wear or

breakage due to misuse and/or abuse.

If the product is defective, return it with a dated proof of purchase, to the retailer

from which you purchased it.

Note: shipping and handling for returns is not included under this warranty.

Customer Service Centre

1-888-468-6876

www.upm-marketing.com

ELECTRICAL SETUP

1) Cut off power at the circuit breaker to avoid electric shock.

load 1800W (resistive)

or 1000W (tungsten).

2) Attach the timer on wall with screw. To avoid shock hazard, timer must be installed

vertically, and at least 3 ft above ground level.

3) Plug the timer into a standard 120V electrical outlet, then plug the device you want to

control into the timer outlet.

4) Apply power at the circuit breaker.

5) Press and hold MODE for 3 seconds to activate the ON/OFF manual override,

to test if the device is working.

Note: Ensure the does not exceed the maximum load rating of

DUSK TO DAWN MODE

This timer is equipped with a photocell that senses ambient light levels. In dusk to

dawn mode, the timer will turn the power on when light levels drop and the unit is

in darkness and will turn off the power when it is light again. This is the default

setting of the timer and it will function in this mode when first plugged in.

The automatic on/off can be tested by covering up the photocell for 8 seconds to

turn the power on and exposing it to the light for 8 seconds to turn it off.

Please note that in the event of a power failure or if the ON and OFF times are

identical the timer will go back to operating as a dusk to dawn timer.

SET CLOCK

1) ress

(The hour will flash on the LCD display)

2) Press to scroll to the correct hour.MODE

3) Press (The minute will flash on the LCD display)SET

4) Press to scroll to the correct minute.MODE

5) Press SET

After the correct time has been selected, the SET icon will disappear, and the

timer will return to normal clock display (with only the CLOCK icon displayed).

Note: To toggle between and format, wait until the time setting is 12 hour 24 hour

complete (when no numbers are flashing, but the CLOCK icon is still visible).

Then press and hold and at the same time (for 3 seconds) to toggle MODE SET

between 12 and 24 hours. (The time before (12) noon looks the same in either 12

or 24 hour mode, but you will be able to see the difference if you scroll up to

1:00pm, because the number will display as 13:00 hours in 24 hour mode.)

This change will affect the program times as well.

P while the SET CLOCK icon is displayed on the LCD.

hp://waterheatermer.org/UPM-mers-and-manuals.html

Specyfikacje produktu

Marka:	UPM
Kategoria:	przełącznik
Model:	DT523H
Technologia łączności:	Bezprzewodowy
Pasmo częstotliwości:	2.4 GHz
Interfejs urządzenia:	RF Wireless
Technologia wykrywania ruchu:	Optyczny
Liczba przycisków:	5
Rozdzielczość ruchu:	1000 DPI
Dołączona myszka:	Tak
System operacyjny:	Windows Vista/XP
Minimalne wymagania systemowe:	Port USB
Rolka przewijająca:	Tak