Instrukcja obsługi Tripp Lite SUPDMB710HW

Tripp Lite Niesklasyfikowane SUPDMB710HW

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Tripp Lite SUPDMB710HW (8 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/8
1
Owner’s Manual
Manual del propietario / Manuel du propriétaire
Series Number / Número de serie / Numéro de série :
AGAC5553 (SUPDMB710), AGAC5591 (SUPDMB710HW), AGPD7040 (SUPDMB710IEC)
Español 4 • Français 6
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
Copyright © 2018 Tripp Lite. All rights reserved.
Copyright © 2018 Tripp Lite. Todos los derechos reservados. / © 2018 Tripp Lite. Tous droits réservés.
PROTECT YOUR INVESTMENT!
Register your product for quicker service and ultimate peace of mind.
You could also win an ISOBAR6ULTRA surge protector—a $100 value!
www.tripplite.com/warranty
Detachable Power Distribution Modules
SUPDM Series
For use with SmartOnline
® Rack/Tower UPS Systems requiring a detachable PDM.
Módulos de distribución de potencia desmontables
Serie SUPDM
Para uso con UPS SmartOnline
® de montaje en bastidor/torre que requiera un PDM desmontable.
Modules de distribution d’alimentation détachables
Série SUPDM
Pour utilisation avec les systèmes UPS SmartOnline
® en bâti ou en tour, exigeant un PDM (module de distribution d’alimentation) détachable.
2
Important Safety Warnings! SAVE THESE INSTRUCTIONS.
Connecting the SUPDM to the UPS Power Module
1 If the the Power Module contacts A and/or SUPDM contacts B are protected by a box or cover, unscrew and remove it to expose the contacts. Consult your
UPS Owner’s Manual for the exact location of the contacts on your Power Module and SUPDM.
2 Align the SUPDM and Power Module contacts C.
3 Secure the SUPDM to the Power Module with screws D (included). Consult your UPS Owner’s Manual for detailed installation instructions.
4 Connect the SUPDM to utility power, either by plugging it into an AC wall outlet or by hardwiring it to an appropriate AC power source, as applicable.
5 Connect your equipment to the UPS either by plugging it in or hardwiring it to the SUPDM.
CAUTION: Hardwiring should only be performed by a qualified electrician.
Consult your UPS Owner’s Manual for specific connection/hardwiring instructions, or call Tripp Lite for assistance at 773.869.1234.
This manual contains important instructions and warnings that should
be followed during the installation and operation of all SUPDM Power
Distribution Modules. Use this manual in conjunction with the owner’s
manual for your SmartOnline Rackmount/Tower UPS System. Follow all safety
warnings, including the following:
• SUPDM connection must be performed by qualified service personnel.
• The UPS system must be powered down and completely disconnected
from utility power, external battery module(s) and connected equipment
prior to connecting the SUPDM.
• There are no user serviceable parts. Do not modify or drill holes into
enclosure. Installation, maintenance is by Qualified Service personnel
only.
• This unit is intended for installation in a temperature-regulated, indoor
area that is relatively free of conductive contaminants.
• Use of this equipment in life support applications where failure of this
equipment can reasonably be expected to cause the failure of the life
support equipment or to significantly affect its safety or effectiveness is
not recommended. Do not use this equipment within oxygen-enriched
atmospheres, or within 0.3 m (1 ft.) of a point at which an oxygen-
enriched atmosphere is intentionally vented.
AC Mains Installation
• Install in accordance with National Electrical Code standards.
• Be sure to use the proper wire size: 6AWG / 6 mm2 rated a minimum of
60C and overcurrent protection for the installation, in accordance with the
plug/equipment rating.
• Over-current protection shall be provided in the end use application,
installed in accordance with local and national electrical wiring regulations.
• In the US/Canada, the plug rating is required to be 125% of the
equipment current rating. Note if the equipment is rated 50A, then 50 x
125% = 62.5A plug is required.
• CAUTION: To reduce the risk of fire, connect only to a circuit provided
with a 50A branch circuit overcurrent protection in accordance with the
National Electrical Code, ANSI/NFPA 70 and the Canadian Electrical Code,
Part I, C22.1.
• Short circuit back-up protection to be provided by building installation
• Be sure to provide a local disconnect device on any models that are
permanently installed without a plug that is easily accessible.
• For pluggable equipment the mains socket outlet that supplies the
equipment shall be installed near the equipment and shall be easily
accessible.
• Be sure to use conduit for permanently installed wiring to meet National/
local codes as required.
• The total load connected to the PDU must not exceed the maximum load
rating for the PDU.
• Use a properly sized Gland Fitting for flexible cables to provide strain relief.
• Use conduit/gland fittings for permanent connections, according to local/
national regulations.
High Voltage Warnings
Contacts on Power/Battery Module
(your model may differ)
Contacts on Detachable PDM
(your model may differ)
WARNING! High Voltage!
Risk of electrical shock!
Due to the presence of high voltage batteries, even without AC
present, these contacts A are live! Do not let these contacts
touch any surface!
WARNING! High Voltage!
Risk of electrical shock!
If AC is present and Bypass Switch is set to “Bypass”, these
contacts B are live! Do not let these contacts touch any surface!
A
A
SUPDMB56
SUPDM56HW
SUPDMB568HW
SUPDMB710
SUPDM710HW
SUPDMB710HW
SUPDMB710IEC
B
B
3
1 2 3 4 5
A
B
C
D
SUPDM56HW
SUPDMB568HW
SUPDMB710
SUPDMB710IEC
SUPDM710HW
SUPDMB710HW
SUPDMB56
1 2 3 4 5
D
A
B
C
1 2 3 4 5
B
C
D
1 2 3 4 5
A
C
D
B
1 2 3 4 5
A
C
D
B
1 2 3 4 5
D
A
C
1 2 3 4 5
A
B
C
D
B
A

Specyfikacje produktu

Marka: Tripp Lite
Kategoria: Niesklasyfikowane
Model: SUPDMB710HW

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Tripp Lite SUPDMB710HW, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Tripp Lite

Tripp Lite

Tripp Lite B127A-1A1-BDBH Instrukcja

12 Października 2024
Tripp Lite

Tripp Lite BP36V15-2U Instrukcja

9 Października 2024
Tripp Lite

Tripp Lite RBC92-2U Instrukcja

9 Października 2024
Tripp Lite

Tripp Lite SRCOMBO Instrukcja

8 Października 2024
Tripp Lite

Tripp Lite U360-004-MINI Instrukcja

7 Października 2024
Tripp Lite

Tripp Lite PS-406-HGULTRA Instrukcja

7 Października 2024
Tripp Lite

Tripp Lite T014-001 Instrukcja

7 Października 2024
Tripp Lite

Tripp Lite RBC7A Instrukcja

7 Października 2024
Tripp Lite

Tripp Lite N250-P12 Instrukcja

7 Października 2024
Tripp Lite

Tripp Lite PS410HGUK Instrukcja

6 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024