Instrukcja obsługi Tripp Lite SmartRack SR4POST

Tripp Lite Niesklasyfikowane SmartRack SR4POST

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Tripp Lite SmartRack SR4POST (8 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/8
Quick Assembly Guide
SmartRack™ 4-Post Open Frame Racks
(SR4POST, SR4POST1224,
SR4POST13, SR4POST25)
Contents:
Section 1 – Parts Identification
Section 2 – Rack Assembly
Section 3 – Optional Casters
Section 4 – Service & Warranty
SAVE THESE INSTRUCTIONS
This manual contains important instructions and warnings that must be followed during installation.
Failure to comply may affect the warranty.
PROTECT YOUR INVESTMENT!
Register your product for quicker service and ultimate peace of mind.
You could also win an ISOBAR6ULTRA surge protector—a $100 value!
www.tripplite.com/warranty
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
Copyright © 2015 Tripp Lite. All rights reserved. All trademarks are the sole property of their respective owners.
A
H
H
C
F
D
I
O
J
P Q R S
K
T
L
U
M
V
N
W X
F
G
E
G
D
F
B
B
A
C
F
ADJUSTABLE MOUNTING DEPTH: 22 TO 36 in.
2
1 – Parts Identification
After opening the shipping box, lay out the parts on a flat surface for identification. If anything is missing or
damaged, go to www.tripplite.com/support for assistance.
Note: SR4POST is shown. SR4POST13 & SR4POST25 are shorter (13U & 25U, respectively) and SR4POST1224 uses round/threaded
equipment mounting holes instead of square holes. However, the rack assembly process for all 4 models is identical.
Rack Components
A “Left” Vertical Rail (2)
B “Right” Vertical Rail (2)
C Base Bracket (2)
D Bottom Corner Section (4)
E Bottom Center Section (2)
F Top Corner Section (4)
G Top Center Section (2)
H Top Bracket (2)
Rack Assembly Hardware
I M8 Acorn/Cap Nuts (12)
J M8 Bolts (16)
K M8 Washers (28)
L M8 Hex Nuts (4)
Rack Assembly Tool
M M8 (13 mm) Wrench
Equipment Mounting Hardware
(SR4POST, SR4POST13, SR4POST25 Only)
N M6 Cage Nuts (Qty. varies per model)
O PVC Cup Washers (Qty. varies)
P M6 Phillips-Head Screws (Qty. varies)
Equipment Mounting Hardware
(SR4POST1224 Only)
Q #12-24 Phillips-head Screws (50)
R Black PVC Washers (50)
S White PVC Washers (50)
Grounding Hardware
(Optional Installation)
T M4 Hex Nuts (2)
U M4 Bolts (2)
V M4 Washers (2)
Cable Management Hardware
(Optional Installation)
W Cable Management Hooks (Qty. varies)
X Hook Mounting Screws (Qty. varies)
2-1
F FG
K K
J J
2-2
D E D
K K
J J
3
2 – Rack Assembly
Warning: Install the rack in a controlled, structurally sound, indoor environment with
a level floor. Use appropriate caution when moving the rack and consider whether you
require assistance. Assemble the rack completely and confirm its stability before
attempting to install equipment in the rack.
Note: SR4POST is shown, but the assembly process is identical for SR4POST1224, SR4POST13, & SR4POST25.
Rack Depth Index
Mounting Depth Index Numbers
36 in. 8 and 8
35 in. 7 and 8
34 in. 7 and 7
33 in. 6 and 7
32 in. 6 and 6
31 in. 5 and 6
30 in. 5 and 5
29 in. 4 and 5
28 in. 4 and 4
27 in. 3 and 4
26 in. 3 and 3
25 in. 2 and 3
24 in. 2 and 2
23 in. 1 and 2
22 in. 1 and 1
Repeat the process in to assemble the other top section. Step 2-1
Make sure the depths match by using the same pair of index
numbers. Lay the assembled sections side by side to confirm that
they’re the same length.
2-2 Assemble a bottom section by sliding two bottom corner sections D inside the ends of a bottom center
section E. The index numbers printed on the corner sections correspond to the rack’s mounting depth. Align
the sections so the index numbers match the numbers you used for the top sections. When the sections are
aligned at the correct depth, use two M8 bolts J and M8 washers K to fasten each section in place. The
bolts will pass through the center section and into threaded holes in the corner sections. Tighten the bolts
approximately 90% with the included wrench.
Repeat the process in to assemble the other bottom section. Lay the assembled top and bottom Step 2-2
sections side by side to confirm that all sections are the same length.
2-1 Assemble a top section by sliding two top corner sections F over
the ends of a top center section G. Align the sections so the index
numbers printed on the center section show through the cutouts
in the corner sections. The index numbers correspond to the rack’s
mounting depth, which is adjustable from 22 inches to 36 inches in
1-inch increments. You can set the rack to the required mounting
depth by cross-referencing the index numbers with the table at
right. When the sections are aligned at the required depth, use an
M8 bolt J and M8 washer K to fasten each section in place. The
bolt will pass through the corner section and into threaded holes in
the center section. Tighten the bolts approximately 90% with the
included wrench – they should be fixed in place, but not completely
tightened.
Note: You’ll finish tightening all nuts and bolts when the rack is fully assembled.

Specyfikacje produktu

Marka: Tripp Lite
Kategoria: Niesklasyfikowane
Model: SmartRack SR4POST

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Tripp Lite SmartRack SR4POST, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Tripp Lite

Tripp Lite

Tripp Lite B127A-1A1-BDBH Instrukcja

12 Października 2024
Tripp Lite

Tripp Lite BP36V15-2U Instrukcja

9 Października 2024
Tripp Lite

Tripp Lite RBC92-2U Instrukcja

9 Października 2024
Tripp Lite

Tripp Lite SRCOMBO Instrukcja

8 Października 2024
Tripp Lite

Tripp Lite U360-004-MINI Instrukcja

7 Października 2024
Tripp Lite

Tripp Lite PS-406-HGULTRA Instrukcja

7 Października 2024
Tripp Lite

Tripp Lite T014-001 Instrukcja

7 Października 2024
Tripp Lite

Tripp Lite RBC7A Instrukcja

7 Października 2024
Tripp Lite

Tripp Lite N250-P12 Instrukcja

7 Października 2024
Tripp Lite

Tripp Lite PS410HGUK Instrukcja

6 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024