Instrukcja obsługi Tripp Lite SmartPro SMART3000CRMXL
Tripp Lite
UPS
SmartPro SMART3000CRMXL
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Tripp Lite SmartPro SMART3000CRMXL (56 stron) w kategorii UPS. Ta instrukcja była pomocna dla 12 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/56
1
Owner’s Manual
SmartPro® Rackmount
Intelligent, Line-Interactive UPS Systems
Not suitable for mobile applications.
Models:
SMART1500CRMXL SMART2200CRMXL SMART3000CRMXL
(Series No. AGSM6953)
(Series No. AG-033F)
(Series No. AGSM6876) (Series No. AGSM6877)
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
Copyright © 2019 Tripp Lite. All rights reserved. SmartPro
® is a registered trademark of Tripp Lite.
Important Safety Instructions 2
Mounting 4
Quick Installation 6
Optional Installation 8
Basic Operation 11
Storage and Service 16
Product Registration 16
Battery Replacement 17
Español 19
Français 37
PROTECT YOUR INVESTMENT!
Register your product for quicker service
and ultimate peace of mind.
You could also win an
ISOBAR6ULTRA surge protector—
a $100 value!
www.tripplite.com/warranty
19-01-060-932757.indb 1 1/21/2019 9:56:33 AM
2
Important Safety Instructions
SAVE THESE INSTRUCTIONS
This manual contains important instructions that should be followed during the
installation, operation and storage of this product. Failure to heed these warnings
may affect the warranty.
UPS Location Warnings
• Use caution when lifting the UPS. Because of the considerable weight of all rackmount
UPS systems, at least two people should assist in lifting and installing them.
• Install the UPS indoors, away from excess moisture or heat, dust or direct sunlight.
• For best performance, the ambient temperature near the UPS should be between 0° C
and 40° C (between 32° F and 104° F).
• Leave adequate space around all sides of the UPS for proper ventilation. Do not obstruct
its vents or fan openings.
• When mounting the UPS system in a tower orientation, make sure the LCD panel is at
the top of the UPS, not at the bottom.
• Do not mount unit with its front or rear panel facing down (at any angle). Mounting in
this manner will seriously inhibit the unit’s internal cooling, eventually causing product
damage not covered under warranty.
UPS Connection Warnings
• The UPS contains its own energy source (battery). The output terminals may be live even
when the UPS is not connected to an AC supply.
• Connect the UPS to a properly grounded AC power outlet. Do not modify the UPS plug
in a way that would eliminate the UPS’s connection to ground. Do not use adapters that
eliminate the UPS’s connection to ground.
• Do not plug the UPS into itself; this will damage the UPS and void your warranty.
• If you are connecting the UPS to a motor-powered AC generator, the generator must
provide filtered, frequency-regulated computer-grade output. Connecting the UPS to a
generator will void its Ultimate Lifetime Insurance.
• Install in accordance with National Electrical Code standards ANSI/NFPA 70 and
Canadian Electrical Code, Part I, C22.1.
• Short circuit backup protection and overcurrent protection is provided by the building
installation.
• To reduce the risk of fire, connect only to a circuit provided branch circuit overcurrent
protection in accordance with the National Electrical Code, ANSI/NFPA 70 and the
Canadian Electrical Code, Part I, C22.1. For installation, be sure to use maximum
overcurrent protection in accordance with the plug/equipment rating as follows:
Model Series Number Overcurrent Protection
SMART1500CRMXL AGSM6953, AG033F 20A
SMART2200CRMXL AGSM6876 20A
SMART3000CRMXL AGSM6877 30A
19-01-060-932757.indb 2 1/21/2019 9:56:33 AM
3
Important Safety Instructions
• The plug on the power supply cord is intended to serve as the disconnect device. Be sure
that the socket-outlet is installed near the equipment and is made easily accessible.
• Be sure to provide an easily accessible local disconnect device on permanently
connected models.
Caution! This UPS receives power from more than one source.
Disconnection of the AC and DC sources is required to de-energize the unit
before servicing.
Equipment Connection Warnings
• Use of this equipment in life support applications where failure of this equipment
can reasonably be expected to cause the failure of the life support equipment or to
significantly affect its safety or effectiveness is not recommended.
• Do not connect surge protectors or extension cords to the output of the UPS. This might
damage the UPS and may affect the surge suppressor and UPS warranties.
Battery Warnings
• Batteries can present a risk of electrical shock and burn from high short-circuit current.
Observe proper precautions. Do not dispose of the batteries in a fire. Do not open the
UPS or batteries. Do not short or bridge the battery terminals with any object. Unplug
and turn off the UPS before performing battery replacement. Use tools with insulated
handles. There are no user-serviceable parts inside the UPS. Battery replacement
should be performed only by authorized service personnel using the same number
and type of batteries (sealed Lead-Acid). Tripp Lite offers a complete line of UPS
System Replacement Battery Cartridges (RBC). Visit Tripp Lite on the Web at
www.tripplite.com/products/battery-finder to locate the specific replacement battery for
your UPS. The RBC Type can also be found on the label affixed to the Battery Retention
Plate.
• During hot-swap battery replacement, the UPS will not provide backup power in the event
of a blackout or other power interruptions.
• Do not operate the UPS without batteries.
• See Batttery Replacement section for additional details.
External Battery Connection Warnings
• When adding external battery packs to select models with external battery pack
connectors, connect only Tripp Lite-recommended battery packs of the correct voltage
and type. Do not connect or disconnect battery packs when the UPS is operating on
battery power. Visit www.tripplite.com/products/battery-finder to locate the supported
battery type(s) for your UPS.
19-01-060-932757.indb 3 1/21/2019 9:56:33 AM
Specyfikacje produktu
| Marka: | Tripp Lite |
| Kategoria: | UPS |
| Model: | SmartPro SMART3000CRMXL |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Tripp Lite SmartPro SMART3000CRMXL, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje UPS Tripp Lite
9 Października 2024
9 Października 2024
9 Października 2024
4 Października 2024
1 Października 2024
29 Września 2024
29 Września 2024
16 Września 2024
15 Września 2024
14 Września 2024
Instrukcje UPS
- UPS Ikea
- UPS AEG
- UPS Voltcraft
- UPS LC-Power
- UPS APC
- UPS Block
- UPS V7
- UPS Digitus
- UPS FSP
- UPS Online USV
- UPS Equip
- UPS Emerson
- UPS CyberPower
- UPS JUNG
- UPS Eaton
- UPS Adj
- UPS PowerWalker
- UPS Salicru
- UPS Energenie
- UPS Steren
- UPS East
- UPS Liebert
- UPS Avocent
- UPS Minute Man
- UPS Furman
- UPS Minuteman
- UPS Riello
- UPS Maruson
- UPS Phoenix Contact
- UPS Puls Dimension
- UPS Vanson
- UPS Approx
- UPS Altronix
- UPS Bxterra
- UPS Middle Atlantic
- UPS Atlantis Land
- UPS FSP/Fortron
Najnowsze instrukcje dla UPS
12 Października 2024
12 Października 2024
12 Października 2024
12 Października 2024
12 Października 2024
12 Października 2024
12 Października 2024
12 Października 2024
11 Października 2024
9 Października 2024