Instrukcja obsługi Tripp Lite DSUT1CSU

Tripp Lite Niesklasyfikowane DSUT1CSU

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Tripp Lite DSUT1CSU (12 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/12
1
Owner’s Manual
Network Dataline
Surge Suppressors
Tripp Lite World Headquarters
1111 W. 35th Street, Chicago, IL 60609 USA
(773) 869-1234 • www.tripplite.com
Note: Follow these instructions to ensure proper operation and prevent damage to this device
and its connected equipment.
Copyright © 2008 Tripp Lite. All rights reserved. All trademarks are the property of their respective owners.
Data Shield™ by Tripp Lite Network Dataline Surge Suppressors are designed to protect
data and communications equipment against AC transients caused by lightning, electrostatic
discharge and ground surges that can enter equipment from the signal lines or chassis ground.
Data Shield by Tripp Lite Network Dataline Surge Suppressors described here protect
networked equipment using 100Base-T, 10Base-T, 10Base-2 and Ethernet, Token Ring,
RS232, RS422, parallel, dial-up modems, fax, ISDN, DDS, T-1 and other communication
interfaces.
200810167 93-2858.indd 1 12/16/2008 9:58:50 AM
2
INSTALLATION
1. Make sure the computer, network device or other equipment is logged OFF the network
(if applicable). Turn OFF power to the equipment.
2. Disconnect the cable from the equipment to be protected.
3. Connect the Data Shield by Tripp Lite Network Dataline Surge Suppressor directly to the
equipment. DB9 and DB25 models are reversible, to work with male or female ports. To
change gender, remove the thumbscrews, reverse their direction and re-install.
4. Attach the green ground wire on the surge suppressor directly to the protected
equipment’s chassis. (Except DB9 and DB25 models.)
5. Reconnect the cable to the Data Shield by Tripp Lite Network Dataline Surge
Suppressor.
NOTE!
The Data Shield by Tripp Lite Network Dataline Surge Suppressor must be properly grounded and positioned as close
as possible to the equipment to be protected. For best results, it is required that the length of the signal line and ground
wire (if equipped) between the surge suppressor and the protected equipment be kept as short as possible, not to
exceed 12 inches (12”). It is best to install the surge suppressor directly to the equipment, as noted above.
NOTE!
Installing a typical Data Shield by Tripp Lite Network Dataline Surge Suppressor is equivalent to adding
approximately three feet (3’) of typical data communication cable to a segment.
CAUTION!
The Data Shield by Tripp Lite Network Dataline Surge
Suppressor does not protect the equipment on the opposite end
of the cable. Normally, protection at both ends is recommended.
CAUTION!
Use of this equipment in life support applications where failure
of this equipment can reasonably be expected to cause the
failure of the life support equipment or to significantly affect its
safety or effectiveness is not recommended. Do not use this
equipment in the presence of a flammable anesthetic mixture
with air, oxygen or nitrous oxide.
CAUTION!
When properly installed, the Data Shield by Tripp Lite Network
Dataline Surge Suppressor will only protect against surges on
the dataline portion of your installation. Simultaneous AC surge
suppression/power protection in the form of an ISOBAR® surge
suppressor or Tripp Lite UPS system is strongly recommended
for complete system/network protection and can also extend
Ultimate Lifetime Insurance coverage to connected equipment.
200810167 93-2858.indd 2 12/16/2008 9:58:51 AM
3
SPECIFICATIONS
All surge suppressors listed have component response times of less than 1 picosecond.
Model: Description:
Nominal
Clamping Voltage:
Peak Pulse
Current:
DRS232 RJ45/RJ11 protector for
100Base-T4, RS232 on twisted Pair
(wires 1-8) or ISDN “S/T” interfaces.
Supplied with a 4” RJ45 patch cable.
18 volts, protecting
wires 1-8 1340 amps
DNET1
RJ45 100Base-T, 10Base-T,
Token Ring, RS422, AS400/Sys3x
protector for NICs, hubs, routers,
etc. Supplied with 4” RJ45 patch
cable.
7.5 volts, protecting
wires 1-8 750 amps
DSUT1CSU
RJ45/RJ11 protector for nonspan
powered T-1 equipment, digital data
service CSUs/DSUs, ISDN “U”
interfaces or other digital lines.
Supplied with 4” RJ45 patch cable.
60 volts, protecting
wires 1-8 200 amps
DTEL2 RJ45/RJ11 for modems, answering
and fax machines. Supplied with
4” RJ11 patch cable.
260 volts, protecting center
4 wires (2 CO-lines) 250 amps
DB9
Serial DB9 RS232 protector for male
or female ports of data terminal and
computing equipment including PCs,
modems, etc. (Any male or female
9-pin port). Male/Female genders
are reversible with reversible
thumbscrews.
18 volts, protecting pins
1-9 and chassis 340 amps
DB25
Serial DB25 RS232 protector
(wires 1-8, 20) for male or female
ports of data terminal & computing
equipment including PCs, printers,
modems, etc. Male/Female genders
are reversible with reversible
thumbscrews.
18 volts, protecting pins
1-8, 20 and chassis 340 amps
DB25-ALL DB25-ALL: Serial DB25 RS232
protector (pins 1-25) for any 25-pin
male or female DTE/DCE ports.
Male/Female genders are reversible
with reversible thumbscrews.
18 volts, protecting pins
1-25 and chassis 340 amps
D10B2 10Base-2 thin coax protector (BNC
m/f). Also protects IBM 3270 and
CCTV lines.
7.5 volts, protecting center,
shield and chassis 750 amps
DCATV
Coaxial protector for TVs, VCRs, pro
video supplied by CATV (“F” m/f).
7.5 volts, protecting center
and shield conductors 750 amps
Call Tripp Lite Customer Support at (773) 869-1234 for additional applications.
200810167 93-2858.indd 3 12/16/2008 9:58:51 AM

Specyfikacje produktu

Marka: Tripp Lite
Kategoria: Niesklasyfikowane
Model: DSUT1CSU

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Tripp Lite DSUT1CSU, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Tripp Lite

Tripp Lite

Tripp Lite B127A-1A1-BDBH Instrukcja

12 Października 2024
Tripp Lite

Tripp Lite BP36V15-2U Instrukcja

9 Października 2024
Tripp Lite

Tripp Lite RBC92-2U Instrukcja

9 Października 2024
Tripp Lite

Tripp Lite SRCOMBO Instrukcja

8 Października 2024
Tripp Lite

Tripp Lite U360-004-MINI Instrukcja

7 Października 2024
Tripp Lite

Tripp Lite PS-406-HGULTRA Instrukcja

7 Października 2024
Tripp Lite

Tripp Lite T014-001 Instrukcja

7 Października 2024
Tripp Lite

Tripp Lite RBC7A Instrukcja

7 Października 2024
Tripp Lite

Tripp Lite N250-P12 Instrukcja

7 Października 2024
Tripp Lite

Tripp Lite PS410HGUK Instrukcja

6 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024