Instrukcja obsługi Tissot PRS 200

Tissot Oglądać PRS 200

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Tissot PRS 200 (4 stron) w kategorii Oglądać. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/4
*
www.tissot.ch 143_EN / 12.09
1/4
Chronographs G10
User's Manual
Standard model
Hour hand
Minute hand
Seconds hand
Date indicator
60-second counter hand
30-minute counter
1/10 second counter
Racing Model
Hour hand
Minute hand
Seconds hand
Date indicator
60-second counter
60-minute counter
1/10 second counter
* Models with a screwed down crown:
IA Initial position (screwed down, not pulled out)
IB Neutral position (unscrewed, not pulled out)
Crown with 3 positions (8) :
I
Neutral position (screwed down*, not pulled out)
II
Setting position for date (unscrewed*, half pulled out)
III
Setting position for time (unscrewed*, completely pulled out)
Chronographs G10
*
www.tissot.ch 143_EN / 12.092/4
Settings
Models with a screwed down crown
To ensure even better water-resistance, some models are fitted with a screwed down crown. Before setting the time or date, you must first unscrew the crown to position
IB
, before pulling it out to position
II
or
III.
Important : After each operation, you must always screw the crown back down to ensure that your watch remains water-resistant.
Setting the time
Pull the crown out to position
III
and turn it clockwise or anticlockwise to set the desired time. Synchronise the small seconds hand at the 6 o'clock position with an
official time signal (radio/ TV/Internet) by pulling out the crown to the second notch; the hand will then stop. Once the time has been synchronised, push the crown
back down into position I (and tighten it back down on models with a screwed down crown).
Winding
Quartz watches never need to be wound.
Rapid date correction
Pull the crown out to position
II
and turn it anticlockwise until the correct date is displayed.
Speedometer (depending on the model)
The speedometer is used to measure the speed of an object which is moving at a constant speed. Start the timing operation and stop it again once you have covered
a distance of 1 km. The chronograph hand then points at a numeral on the tachometric scale, indicating the speed in km/h.
Acknowledgements
Thank you for choosing a chronograph from TISSOT®, one of the most highly renowned Swiss brands in the world. Meticulously assembled using high quality
materials and components, it is protected against impacts, temperature variations, water and dust.
This manual applies to TISSOT®
standard and Racing quartz chronographs with G10 movement. For the settings and operation of your chronograph, please refer to
the instructions corresponding to your model.
Your chronograph allows you to time events lasting up to 30 minutes, and offers you the following functions:
Standard chronograph START–STOP function
ADD function (partial times)
SPLIT function (intermediate times)
To ensure that your chronograph operates with perfect precision for many years to come, we advise you to pay careful attention to the advice given in this
manual.
Resetting the counters
The counters must be reset before starting timing. If necessary, proceed as follows:
Reset the 30-minute counter hand:
- Crown in position
III
, push-piece
A
Reset the 60-second counter hand:
- Crown in position
II
, push-piece
B
Reset the 1/10 second counter hand:
- Crown in position
II
, push-piece
A
20
Chronographs G10
*
www.tissot.ch 143_EN / 12.093/4
Simple timing
The "simple timing" function enables you to measure isolated events.
1
START
2
STOP
Time readout (as per example above)
- 5 minutes,
- 57 seconds,
- 7/10ths of a second
3
Reset
NB:
Before each timing operation, the chronograph hands must be at their start points. If necessary, refer to
the
RESETTING THE COUNTERS paragraph.
Note :
All the timing functions are available with the crown pressed into position
I.
ADD function
The ADD function enables you to measure consecutive events without having to reset in between. Each time
is added to the previous total.
1
START
2
STOP
Readout
3
RESTART
4
STOP
Readout
5
RESTART
6
STOP
Readout
X
Reset counters
SPLIT-TIME function
The SPLIT-TIME function enables you to stop the hands to read an intermediate time, without interrupting
timing. When you restart, the chronograph hands "catch up" to the ongoing elapsed time.
1
START
2
SPLIT 1
Time 1 readout (as per fig. 2)
- 5 minutes,
- 4 seconds,
- 6/10ths of a second
3
RESTART (catchup)
4
SPLIT 2
Time 2 readout
- 15 minutes,
- 36 seconds,
- 8/10ths of a second
5
RESTART (catchup)
6
STOP
Final time readout (cumulative time)
- 25 minutes,
- 18 seconds,
- 4/10ths of a second
7
Reset counters

Specyfikacje produktu

Marka: Tissot
Kategoria: Oglądać
Model: PRS 200

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Tissot PRS 200, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Oglądać Tissot

Instrukcje Oglądać

Najnowsze instrukcje dla Oglądać

Casio

Casio G-Shock GMA-B800 Instrukcja

9 Października 2024
Rolex

Rolex Submariner Instrukcja

9 Października 2024
Casio

Casio GW-3000BD-1AER Instrukcja

9 Października 2024
Seiko

Seiko 6N76 Instrukcja

8 Października 2024
Seiko

Seiko 6N53 Instrukcja

8 Października 2024
Seiko

Seiko 6N52 Instrukcja

8 Października 2024
Seiko

Seiko 6G28 Instrukcja

8 Października 2024
Seiko

Seiko 4N30 Instrukcja

8 Października 2024
Seiko

Seiko 4227 Instrukcja

8 Października 2024
Seiko

Seiko 6N32 Instrukcja

8 Października 2024