Instrukcja obsługi Tanaka TCS 33ED

Tanaka Maszyna do piłowania TCS 33ED

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Tanaka TCS 33ED (20 stron) w kategorii Maszyna do piłowania. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/20
Chain Saw
Model TCS 33ED
Handling instructions
Note:
Before using this machine, carefully read through these HANDLING INSTRUCTIONS
to ensure effi cient, safe operation. It is recommended that these INSTRUCTIONS be
kept readily available as an important reference when using this machine.
2
MEANINGS OF SYMBOLS
NOTE: Some units do not carry them.
Symbols
WARNING
The following show symbols used for the machine. Be sure that you understand their meaning before use.
It is important that you read, fully understand and
observe the following safety precautions and
warnings. Careless or improper use of the unit may
cause serious or fatal injury.
Emergency stop
Read, understand and follow all warnings and
instructions in this manual and on the unit. Fuel and oil mixture
Always wear eye, head and ear protectors when using
this unit. Chain oil fi ll
Warning, kickback danger. Be careful of possible
sudden and accidental upward and/or backward
motion of the guide bar.
Carburetor adjustment - Idle speed
One-handed usage not permitted. While cutting, hold
chain saw fi rmly with both hands with thumb fi rmly
locked around front handle.
Carburetor adjustment - Low speed mixture
Chain brake Carburetor adjustment - High speed mixture
Choke - Run position (Open) Priming pump
Choke - Start position (Closed)
4
Guaranteed Sound power level
On/Start Hot surface
Off /Stop Oil pump adjustment
Contents
WHAT IS WHAT? .............................................................................. 3
WARNINGS AND SAFETY INSTRUCTIONS .................................. 4
SPECIFICATIONS ............................................................................ 6
ASSEMBLY PROCEDURES ............................................................. 7
OPERATING PROCEDURES ........................................................... 8
MAI NT ENA NCE .............................................................................. 12
Parts breakdown
3
WHAT IS WHAT?
1. Throttle lever: Device activated by the operatorʼs fi nger, for
controlling the engine speed.
2. Throttle lever lockout: Device that prevents the accidental
operation of the throttle lever until manually released.
3. Stop switch: Device for allowing the engine to be started or
stopped.
4. Oil tank cap: For closing the oil tank.
5. Recoil starter: Pull handle to start the engine.
6. Front handle: Support handle located at or towards the front of
the engine housing.
7. Fuel tank cap: For closing the fuel tank.
8. Rear handle: Support handle located at or towards the rear of the
engine housing.
9. Choke lever: Device for enriching the fuel/air mixture in the
carburetor, to aid starting.
10. Priming pump; Device for supplying extra fuel, to aid starting.
11. Guide bar: The part that supports and guides the saw chain.
12. Saw chain: Chain, serving as a cutting tool.
13. Chain brake (Front hand guard): Device for stopping or locking
the chain.
14. Chain catcher: device for restraining the saw chain.
15. Air fi ler cover: Cover for air fi lter and carburetor.
16. Side case: Protective cover to the guide bar, saw chain, clutch
and sprocket when the chain saw is in use.
17. Tension adjustment bolt: Device, often acting on the guide bar,
for adjusting the saw chain tension.
18. Chain oil adjusting screw: Device for adjusting the delivery of
saw chain oil to the guide bar and the saw chain.
19. Muffl er: Reduces engine exhaust noise and directs the exhaust
gases.
20. Anti-vibration spring: Reduce the transmission of vibrations to
the operator's hands.
21. Anti-vibration rubber: Reduce the transmission of vibrations to
the operator's hands.
22. Chain bar clamp nut: Secures the side case and the guide bar.
23. Spiked bumper: Device for acting as a pivot when in contact with
a tree or log.
24. Guide bar cover: Device for covering the guide bar and saw
chain when the unit is not being used.
25. Combi box spanner: The tool for removing or installing a spark
plug and tensioning the saw chain.
26. Handling instructions: Included with unit. Read before operation
and keep for future reference to learn proper, safe techniques.
27. Hot surface caution label: Label for caution to hot surface.
26
23
24 25
1
20
8
2110
4
7
3
5
2
6
9
27 18
15
13
22 12
11
19
21 23
14
17
16
20

Specyfikacje produktu

Marka: Tanaka
Kategoria: Maszyna do piłowania
Model: TCS 33ED

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Tanaka TCS 33ED, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Maszyna do piłowania Tanaka

Tanaka

Tanaka TCS-3351PFS Instrukcja

25 Września 2024
Tanaka

Tanaka TCS27EPAP Instrukcja

25 Września 2024
Tanaka

Tanaka TCS-3301PFS Instrukcja

25 Września 2024
Tanaka

Tanaka TCS33EDTP Instrukcja

25 Września 2024
Tanaka

Tanaka TCS 51EAP Instrukcja

24 Września 2024
Tanaka

Tanaka TCS 3401S Instrukcja

24 Września 2024
Tanaka

Tanaka TCS 33EDTP Instrukcja

24 Września 2024
Tanaka

Tanaka ECV-3801 Instrukcja

24 Września 2024
Tanaka

Tanaka TCS 33EDT Instrukcja

24 Września 2024
Tanaka

Tanaka TCS 33ED Instrukcja

24 Września 2024

Instrukcje Maszyna do piłowania

Najnowsze instrukcje dla Maszyna do piłowania

Makita

Makita 5603 Instrukcja

15 Października 2024
MSW

MSW -TAS287 Instrukcja

15 Października 2024
MSW

MSW T-SAW300 Instrukcja

15 Października 2024
Black & Decker

Black & Decker KS650 Instrukcja

14 Października 2024
Black & Decker

Black & Decker GKC3630L20 Instrukcja

14 Października 2024
Ferm

Ferm FKS-165 Instrukcja

14 Października 2024
Royal Catering

Royal Catering RCBS-1650 Instrukcja

14 Października 2024
Royal Catering

Royal Catering RCBS-1650.1ECO Instrukcja

14 Października 2024
Husqvarna

Husqvarna 365H Instrukcja

13 Października 2024
Makita

Makita DJV181Z Instrukcja

12 Października 2024