Instrukcja obsługi Swann PRO-T853

Swann Kamera monitorująca PRO-T853

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Swann PRO-T853 (2 stron) w kategorii Kamera monitorująca. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
Swann Communications warrants this product against defects in workmanship and material for a period
of one (1) year from its original purchase date. You must present your receipt as proof of purchase for
warranty validation. Any unit which proves defective during the stated period will be repaired without
charge for parts or labour or replaced at the sole discretion of Swann. The end user is responsible for
all freight charges incurred to send the product to Swann’s repair centres. The end user is responsible
for all shipping costs incurred when shipping from and to any country other than the country of origin.
The warranty does not cover any incidental, accidental or consequential damages arising from the use
of or the inability to use this product. Any costs associated with the fitting or removal of this product
by a tradesman or other person or any other costs associated with its use are the responsibility of the
end user. This warranty applies to the original purchaser of the product only and is not transferable to
any third party. Unauthorized end user or third party modifications to any component will render all
warranties void. By law some countries do not allow limitations on certain exclusions in this warranty.
Where applicable by local laws, regulations and legal rights will take precedence.
This equipment has been tested and found to comply with the limits for Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and the receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected
• Consult the dealer or an experienced radio/TV technician for help
These devices comply with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. These devices may not cause harmful interference.
2. These devices must accept any interference received, including interference that may cause
undesired operation.
Professional HD
Security Camera
1080p HD Bullet Camera
EN INSTRUCTION MANUAL
Security Made Smarter
Important Note: All jurisdictions have specific laws and regulations relating to the use of cameras.
Before using any camera for any purpose, it is the buyer’s responsibility to be aware of all applicable
laws and regulations that prohibit or limit the use of cameras and to comply with the applicable laws
and regulations.
WARNING: MODIFICATIONS NOT APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD
VOID USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
Helpdesk/Technical Support 5 Limited Warranty - Terms & Conditions 6 FCC Verification
tech@swann.com
support.swann.com
USA 1800 627 2799
USA Parts & Warranty 1800 627 2799
(M-F, 9am-5pm US PT)
Australia 1800 788 210
New Zealand 0800 479 266
UK 0808 168 9031
MT853CAMVER1E
250716
© Swann Communications 2016
Congratulations on your purchase of the Swann 1080p Professional HD Security Camera.
You’ve made a fine choice for keeping a watchful eye over your home or business. The
camera delivers brilliant and amazingly clear high definition images and videos in both day
and nighttime conditions even in complete darkness.
The camera also has an OSD (On-Screen Display) that you can access to change advanced
image settings using the PTZ control interface on your DVR. For details on using the
camera’s OSD feature, download the “ from .T853 OSD Manual” support.swann.com
DVR Compatibility
The camera is compatible with the following Swann 1080p DVR models:
• 4500, 4550, 4575, 4750, 5000 & 8075 Series DVRs
This is not an exhaustive list - since the time of publication we will have released newer
DVRs with which the camera may be supported.
Important Safety Instructions
1. Make sure the camera is fixed correctly and stable if fastened in place.
2. Do not operate if wires and terminals are exposed.
The camera is very flexible, and can be installed almost anywhere. Here are some practical
things to consider when choosing a location:
• Place the camera in a position that a potential security threat will find it difficult to
avoid detection. A strategy which is often effective is to monitor entrances and exits -
after all, a security threat has to get in somewhere.
• Ensure the camera is located close enough to what you want to monitor to capture the
required details. For example, if you wish to capture the details of a face, the camera
may need to be located within 15ft (about 5m) of the subject. This is also true if trying
to read printed information - such as a vehicle’s registration plate.
• Mount as high as possible, out of easy reach to prevent tampering. For example, under
the eaves of a roof or high up in protected corners of a wall would be good options.
• Typically, the best view is obtained approximately 7ft (2m) to 10ft (3m) high, looking
slightly downwards.
• While the camera is sealed, robust and able to handle the weather, long-term
exposure to direct sunlight and moisture will eventually cause a degradation in
performance, so if it’s going to be installed outdoors, make sure it’s in a sheltered spot.
• The camera’s night vision will give well-exposed images if the area is dark. However,
if there’s a bright point source in the camera’s view (a streetlight, car headlights or
similar) then it might not engage night vision mode.
The camera can be mounted onto a flat surface using screws. The surface must have
sufficient strength to hold the camera.
• Position the camera in the location you want to mount it, and mark the screw holes
on the surface to position the screws. Then, using appropriate screws for the surface
you’re fixing the camera to, secure the camera into place.
• If you’re mounting to a wooden surface, then screw the camera directly to the surface.
• If you’re mounting to a masonry surface (bricks, concrete or similar), then you’ll need
to use wall plugs.
Aiming the camera
You can use the included allen key to adjust the camera angle.
• To adjust the orientation, loosen the screw indicated by 1.
This enables you to rotate the camera so no matter what
direction it is facing, your images will be the right way up.
• To tilt up and down, loosen the screw indicated by 2.
• To pan left and right, loosen the locking ring indicated by 3.
Be sure to tighten the screws/ring back securely to lock the
camera’s position in place after you’ve finished adjusting the
viewing angle of the camera.
1 3 5 7
2 4 6 8
VIDEO
INPU T
VIDEO
INPU T
VGAVGA
PT ZPT Z
AUDI O
INPU T
AUDI O
INPU T
AUDI O
OUT PU T
AUDI O
OUT PU T 12V12V
LANLAN
Follow the example diagram below to connect the camera to your DVR.
Extension
cable
Digital Video Recorder
Power Power adapter
Video
Tip: Twist to lock
video connectors
1. Connect the camera’s Power and Video cable
to the extension cable’s DC and BNC plugs.
2. Connect the other end of the BNC extension
cable to a video input channel on your DVR.
3. Connect the other end of the DC extension
cable to the power adapter and then plug the
power adapter into a wall outlet. (For multi-
pack cameras, use the power splitter cable
included with the power adapter.)
Note: Images contained in this diagram
are for illustrative purposes only.
1
2
3
2 Choosing a location for your camera1 Welcome 3 Connecting the camera 4 Mounting the camera
Tip: Run cables inside a wall cavity or other protected
enclosure, and ensure that all wiring and the connectors are
suitably insulated and protected from moisture and sunlight.
1
2
3

Specyfikacje produktu

Marka: Swann
Kategoria: Kamera monitorująca
Model: PRO-T853

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Swann PRO-T853, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Kamera monitorująca Swann

Swann

Swann SWNHD-866MSD Instrukcja

2 Października 2024
Swann

Swann Pro DVR8-4000 Instrukcja

28 Września 2024
Swann

Swann DVR4-1000 Instrukcja

22 Września 2024
Swann

Swann Enforcer SWPRO-4KMQB Instrukcja

19 Września 2024
Swann

Swann SW312-HMD-CA Instrukcja

16 Września 2024
Swann

Swann PRO-A851 Instrukcja

15 Września 2024
Swann

Swann SWIFI-PTCAM232GB Instrukcja

12 Września 2024
Swann

Swann AllSecure650 SWNVK-650KH4 Instrukcja

12 Września 2024
Swann

Swann PrivateEye ADS-45 Instrukcja

9 Września 2024
Swann

Swann SW331-PR5 Instrukcja

9 Września 2024

Instrukcje Kamera monitorująca

Najnowsze instrukcje dla Kamera monitorująca

Dahua Technology

Dahua Technology Pro IPC-HDPW5442G-Z Instrukcja

15 Stycznia 2025
Toshiba

Toshiba IKS-WR7412 Instrukcja

13 Stycznia 2025
AVerMedia

AVerMedia FC1320-P Instrukcja

13 Stycznia 2025
Digitus

Digitus OptiMax DN-16037 Instrukcja

13 Stycznia 2025
Hikvision

Hikvision DS-2CE59U1T-AVPIT3ZF Instrukcja

12 Stycznia 2025
Hikvision

Hikvision IDS-2CD7526G0-IZHSY Instrukcja

12 Stycznia 2025
Hikvision

Hikvision DS-2CD2163G0-I(S) Instrukcja

12 Stycznia 2025
Hikvision

Hikvision DS-2CD2H83G1-IZS Instrukcja

12 Stycznia 2025
Speco Technologies

Speco Technologies O5LB1 Instrukcja

12 Stycznia 2025
ZKTeco

ZKTeco AntarVis 2.0 Instrukcja

12 Stycznia 2025