Instrukcja obsługi Swann ADW-410

Swann Kamera monitorująca ADW-410

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Swann ADW-410 (2 stron) w kategorii Kamera monitorująca. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

123

456

789

Digital Monitor & Recorder

Quick Start Guide

Welcome!

Lets get started.

Congratulations on the purchase of your Digital Monitor & Recorder device. This quick start

guide will assist you with getting your device up and running as soon as possible. We recommend

that you connect everything and give it a try before you do a permanent installation, to make

sure nothing was damaged during shipping.

A) Power Switch - Switch this to the ON

position to turn the device on. Switch to the

OFF position to turn the device off.

B) Micro-SD Card Slot - Insert a Micro-SD

card into this slot. A Micro-SD card is required

to record video events. It is compatible with

cards up to 32GB in size.

Power Socket - Connect the power

adapter here.

As the device has a built-in

battery, disconnecting the power adapter will

not turn the device off. Use the power switch

to turn the device off.

QH_410PK2260214E | © Swann 2014

AGetting to know your device

CStep Two DStep Three EConnect to your Home Network

Screw the included antenna

clockwise to the gold

coloured connection on the

camera. Continue until it is

securely fastened. Position

the antenna upright for best

reception quality.

You should now see a live video

image appear on-screen. For a full

explaination of the various icons

and options available, please have

a look at the setup guide included.

A B C

D) Antenna - Adjust the antenna so they are

placed vertically.

E) Reset - If the device becomes unrespon-

sive, use a paperclip to reset.

F) Speaker - Audio transmitted from the

camera and audio alerts from the device will

be heard from here.

G) Stand - Pull out the stand so you can place

the device on a flat surface for easy viewing.

H) LAN - Connect this to your home network

so you can use the Swann DigiView app on

your mobile device.

I) Event LED - This LED will light up blue

whenever an event has occurred. When that

particular event has been viewed on the device,

the LED will turn off.

J) Battery LED - This LED will light up green

to indicate that the battery is fully charged.

When charging the battery, the LED will

light up orange. When the battery is run-

ning very low, the LED will turn red and

start flashing.

K) Home Button - Press the home button to

access the main menu. Press it again to view

a live video image from your camera(s). For

a full explaination of the various icons and

options available, please have a look at the

setup guide included.

BStep One

Peel off the plastic cover that is protecting

the LCD display.

Connect the DC 5V power supply

to the power input on the device.

L) IR (Infrared) LEDs -

The camera will use

these in low-light conditions to generate

a black and white image, even in total

darkness.

M) Power LED - The power LED will turn

red to indicate that the camera is working.

When pressing the pair button on the

camera, the LED will momentarily flash.

N) Light Sensor - Detects the amount of

light available and turns on the IR LEDs

when necessary.

O) PIR (Passive infrared) Sensor - This

is an electronic sensor that measures

infrared light radiating from objects in its

field of view.

P) Pair Button - Press to pair the camera

with the Digital Monitor & Recorder device.

Please have a look at the included setup

guide for more information about pairing.

Q) Antenna - The included antenna

connects here.

Connect the DC 9V

power supply to the

other end of the

power cable.

USB In t er ne t Et her ne t

432

Flick the power switch to the ON position. You

will momentarily see a Swann logo and a “No

Signal” message will appear on-screen. Don’t

worry, this is normal.

An Ethernet connection is required

to use the Swann DigiView app on

your mobile device. Connect the

Ethernet cable (supplied) to the

LAN connection on the device,

and then connect the other end to

a spare port on your router.

10 11 12

13 14 15

16 17 18

To monitor the front of the house, whether it is the front garden, driveway or the entrance to

your garage, it is recommended to install the camera where the roof meets the walls of the

house, as illustrated below. This will shelter the camera from the elements, have a better field

of view, and less likely to be vandalized.

It has been found that most burglars will enter your home through the front door, so it is very

important that you install a camera here. It is recommended to install the camera either above

the door or to the side space permitting. Mount the camera in an elevated position so it is out of

range of vandals or would be burglars. Placing the camera at a slight angle will allow you to see

who is approaching your front door as well as giving you the ability to have facial recognition.

Your backyard is mostly filled with a shed with lawn and garden tools, recreational equipment

and children’s toys. It’s a good idea to install a camera so that you have an entire overview of the

backyard. Like the cameras installed at the front of the house, it is recommended to install the

camera where the roof meets the wall of the house. If you have a side gate or more than one

entrance to the backyard, you may want to have an additional camera that is focused to that

area.

It’s recommended that you place cameras inside the house that have high traffic areas such as

entry and exit points (front door), hallways and staircases (if applicable). Other ideal locations

are next to windows and rooms that have high priced valuables such as electronics, antiques

and jewellery.

The Field of View produced by a camera is the area that the camera can see. It is an important

factor to consider as it determines not just what the camera can see, but also the level of detail

that is visible at a given distance. Cameras with a smaller lens, also known as a wide-angle

lens, produce a greater Field of View than cameras with a larger lens. This means that the

camera can see a large area but the objects will appear smaller within the scene area. This is

useful if you want to monitor an entire room or a yard. Cameras with a larger lens also known

as narrow-angle have a smaller Field of View. They can see a limited area, but objects will

appear larger within the scene area. This is useful if you want to monitor a specific target such

as a doorway or entrance.

Lighting

• For best results do not point the camera towards a light source.

• Pointing the camera towards a glass window intending to see outside may result in a poor

image because of glare and lighting conditions inside and outside.

• Don’t place the camera in a shaded area that is looking into a well lit area as this will result

in a poor display. The light to the sensor located at the front of the camera needs to be the

same as the light at the focal target for best results.

• As the camera uses infrared LEDs to see at night, it’s recommended to clean the lens from

time to time if the picture degrades.

BFront of House and Driveway

DBackyard and Side Entrance EIndoors

FCamera Field of View GLighting & Environment Tips H

CFront Door

QH_410PK2260214E | © Swann 2014

Confused on which location to install your cameras? The cameras included with your security

system can be installed in a number of different locations. Camera location can depend on the

following -

Camera Location Tips EN

You may need to install multiple cameras if

you want to focus on specific areas that you

would like to monitor, for example, one for the

driveway, the other on the garage entrance.

1. Distance from the

camera to the record-

ing device.

2. Environmental con-

ditions such as rain or

snow.

3. Lighting conditions

during the day and

night.

4. The area that you

would like to monitor.

When you position cameras correctly, you can eliminate the need for additional cameras to cover

your target area and maximise the efficiency of your security system. On the flip side, if you posi-

tion cameras incorrectly, it can lead to blind spots or to have objects that are not visible or too far

for the cameras to view in detail. Keep these points in mind to get the most out of your security

system.

Mount cameras at an elevated position - Mounting your cameras at an elevated position, can keep

your cameras out of range of vandals or would be burglars. It also allows your camera to have a

high vantage point increasing its viewing area.

Cover your target area - When placing cameras, make sure you provide ample coverage, but not

in excess. For example, if you are trying to cover a backyard gate, don’t zoom in to only have the

gate in frame. Position the camera to cover part of your backyard so you capture as much area as

possible without sacrificing video quality.

Install the camera

where the roof

meets the walls

of the house.

Place the camera at a slight angle.

This will focus on the

side entrance.

Fixed Lens vs. Varifocal Lens

A Fixed Lens is where the camera’s focal

length (Field of View) is permanently set

and cannot be adjusted by the user.

A Varifocal Lens is where the camera’s

lens can be manually adjusted by the

user. This allows for greater flexibility

to optimize the camera picture for your

specific needs.

Environment

• Make sure the power connections are not directly exposed to water or moisture and shielded

from other outdoor elements.

• Weatherproof only means that the camera can be exposed to weather such as rain and snow.

Weatherproof cameras cannot be submerged under water.

• Do not expose the camera where rain and snow will hit the lens directly.

• Cameras geared for cold weather may work in extreme conditions as low as -25° as the

camera produces heat when plugged in.

When installing cameras outside, it is recommended to install the provided data & power cable

away from the elements so it prevents them from deteriorating over time. Whilst cabling, avoid

areas that have a high amount of electrical equipment where electrical interference is expected.

This can create all types of interference to the video picture. Also avoid sharp bends, which can

affect cable impedance and cause interference to the video picture. If you’re using cable ties,

do not over tighten them and avoid using a staple gun to secure as this can potentially damage

the cable. There may be circumstances where you have to join multpiple cables together. Go

to your hardware store, purchase some electrical tape and use this to seal the connection(s)

between each cable. This will prevent moisture and dust forming on the connection(s).

Camera Cables

Summary

1. Protect the cable from the elements to avoid deterioration.

2. Avoid electrical equipment where electrical interefence is expected.

3. Avoid sharp bends and do not bend the cable greater than 90 degrees.

4. Do not overtighten when using cable ties.

5. Avoid using a staple gun to secure the cable to a wall.

6. Do not stretch or apply force greater than 25lbs/11kgs.

7. Use electrical tape to seal the connection(s) when joining multiple cables together.

Wide Angle

Fixed Lens

3.6mm

Narrow Angle

Fixed Lens

6.0mm

This camera will

focus on the garage

entrance.

This camera

will focus on the

driveway entrance.

This will focus on the

entire backyard.

Have a look at the image(s) on the Digital Monitor

& Recorder device first before installing the cameras

permanently.

Most burglars will knock on the front

door first to see if anyone is at home.

Have a look at the image(s) on the Digital Monitor

& Recorder device first before installing the cameras

permanently.

Have a look at the image(s) on the Digital Monitor

& Recorder device first before installing the cameras

permanently.

Have a look at the image(s) on the Digital Monitor

& Recorder device first before installing the cameras

permanently.

Specyfikacje produktu

Marka:	Swann
Kategoria:	Kamera monitorująca
Model:	ADW-410

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Swann ADW-410, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Kamera monitorująca Swann

Swann SWNHD-866MSD Instrukcja

2 Października 2024

Swann Pro DVR8-4000 Instrukcja

28 Września 2024

Swann DVR4-1000 Instrukcja

22 Września 2024

Swann Enforcer SWPRO-4KMQB Instrukcja

19 Września 2024

Swann SW312-HMD-CA Instrukcja

16 Września 2024

Swann PRO-A851 Instrukcja

15 Września 2024

Swann SWIFI-PTCAM232GB Instrukcja

12 Września 2024

Swann AllSecure650 SWNVK-650KH4 Instrukcja

12 Września 2024

Swann PrivateEye ADS-45 Instrukcja

9 Września 2024

Swann SW331-PR5 Instrukcja

9 Września 2024

Instrukcje Kamera monitorująca

Najnowsze instrukcje dla Kamera monitorująca

Dahua Technology Pro IPC-HDPW5442G-Z Instrukcja

15 Stycznia 2025

Toshiba IKS-WR7412 Instrukcja

13 Stycznia 2025

AVerMedia FC1320-P Instrukcja

13 Stycznia 2025

Digitus OptiMax DN-16037 Instrukcja

13 Stycznia 2025

Hikvision DS-2CE59U1T-AVPIT3ZF Instrukcja

12 Stycznia 2025

Hikvision IDS-2CD7526G0-IZHSY Instrukcja

12 Stycznia 2025

Hikvision DS-2CD2163G0-I(S) Instrukcja

12 Stycznia 2025

Hikvision DS-2CD2H83G1-IZS Instrukcja

12 Stycznia 2025

Speco Technologies O5LB1 Instrukcja

12 Stycznia 2025

ZKTeco AntarVis 2.0 Instrukcja

12 Stycznia 2025