Instrukcja obsługi Supermicro SuperServer SYS-E302-12D-8C

Supermicro nieskategoryzowany SuperServer SYS-E302-12D-8C

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Supermicro SuperServer SYS-E302-12D-8C (1 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/1
http://www.supermicro.com MNL-2565-QRG
Board Layout
SuperServer E302-12D-4C/8C Series Quick Reference Guide
Rev 1.0
For more information go to: http://www.supermicro.com/support
!
SAFETY INFORMATION
IMPORTANT: See installation instructions and safety warning before connecting
system to power supply.
http://www.supermicro.com/about/policies/safety_information.cfm
WARNING:
To reduce risk of electric shock/damage to equipment, disconnect power from
server by disconnecting all power cords from electrical outlets.
If any CPU socket empty, install protective plastic CPU cap.
!
WARNING:
Always be sure all power supplies for this system have the same power output.
If mixed power supplies are installed, the system will not operate.
!
Front View & Interface Accessing the System
Mounting Bracket and Wall Mounting
System Features
1. Install the mounting bracket to the wall by using four screws.
2. Unclock the latch on the top of chassis bracket and slide the latch upward.
3. Hang the server system on the mounting bracket hooking the four keyholes on four knobs
of the bracket.
4. Secure the server system to the bracket by s liding the latch back down and flipping tab
to lock.
5. Additional power adapter bracket on the bottom of the chassis bracket.
6. Secure the power adapter by lowering the latch and tightening the screw.
Ch isass
Bracket
Latch
Locking Tab
of Chassis
Bracket
Latch
STEP 2 & 4: Chassis Bracket Latch
Bracket
S wscre
STEP 3: Hanging Server on the Bracket
Caution
Rear Features
Installing the Hard Drive
STEP 5: Chassis Bracket with Power
Adapter Bracket Attached
Power Adapter
Bracket
STEP 6: Power Adapter Bracket
Power Adapter Bracket
Latch
Screw of Power
Adapter Bracket
Latch
STEP 1:
Installing the Mounting Bracket
Screw
The drives can accommodate one fixed 2.5" storage drive of 7mm height,
installed to a mounting tray inside the chassis.
S screw
S screw
Removing the Chassis Cover Removing the Bottom Cover
1. Power down the system.
2. Remove the six screws that hold the cover in place.
3. Lift the cover up and off the chassis.
Jumper Description Default Setting
J1 SIM Card Detection
Quick Reference Table
JBM1 Disable IPMI Share LAN
Pins 1-2: High Active (Default)
Pins 2-3: Low Active
Pins 1-2: IPMI Share Lan Disabled
Open: IPMI Share Lan Enabled (Default)
JBT1 CMOS Clear Open (Normal)
JNS1 SlimSAS Interface Selection
JPF1 Power Force On
Pins 1-2: 4X SATA
Pins 2-3: PCIe p1-x4 (Default)
JPG1
Pins 1-2: ATX Mode (Default)
Pins 2-3: Force PS-ON mode
VGA Enable/Disable Pins 1-2 (Enabled)
JPL1, JPL2, JPL3 LAN1, LAN2, LAN3/4 Enable Pins 1-2 (Enabled)
JPME2 ME Manufacturing Mode Pins 1-2 (Normal)
JPT1 Onboard TPM Enable/Disable Pins 1-2 (Enabled)
JWD1 Pins 1-2 (Reset)Watchdog Timer
LED Description
LED1 Power LED
LED2 UID LED
LED3 Overheat (OH)/Power Fail/Fan Fail LED
LEDM1 IPMI Heartbeat LED
Connector Description
BT1 Onboard Battery
COM1 COM Header
CPU/System Fan Headers (FAN1: CPU Fan)
IPMI LAN
FAN1 - FAN4, FANA, FANB
Dedicated IPMI LAN Port
I-SATA1 and I-SATA3
Serial Link General Purpose I/O Header
Power LED/Speaker (Pins 1-3: Power LED, Pins 4-7: Speaker)
Front Control Panel Header
Intel PCH SATA 3.0 Ports (I-SATA1: SATA DOM Power)
General Purpose I/O Header
M.2 PCIe 3.0 p1-x4 or SATA 3.0 Slot (M-Key 2280)
4-pin IPMI External I
²
C Header
Chassis Intrusion Header
LAN1 Activity LED Header
LAN2 Activity LED Header
LAN3/4 Activity LED Header
I-SGPIO1
JD1
JF1
JGP1
JIPMB1
JL1
JLANLED1
JLANLED2
JLANLED3
JMD1
Connector
JMD2
JMD3 M.2 PCIe 3.0 p1-x1 or USB 2.0 Slot (E-Key 2230)
Description
M.2 PCIe 3.0 p1-x2 or SATA 3.0 or USB 3.0 Slot (B-Key 2280/3042/3052)
M.2 Mounting Holes
JNVI2C1, JNVI2C2
JMD1_SRW1, JMD2_SRW1/2
JMD3_SRW1
JOPPS Reserved for One Pulse Per Second
Non-Volatile Memory (NVMe) I²C Headers
JPH1
JPI2C1
JPWR1
4-pin HDD Power Connector
Power System Management (SMB) I²C Headers
JPV1
24-pin ATX Power Connector (Required)
JRK1
JSD1
JSDP1 - JSDP4
JSFPLED1
JSIM1
JSLIM1, JSLIM2
JSMB1
JSTBY1
JTPM1
JUIDB1
LAN1/2, LAN3/4
LAN5/6
MH1 - MH6
SLOT6
SLOT7
USB0/1, USB2/3
USB4/5
VGA
8-pin CPU Power Connector (Required)
Intel RAID Key Header
SATA DOM Power Connector
Reserved for time synchronization
LAN5/6 Activity LED header
NANO SIM Slot for JMD2
SlimSAS PCIe 3.0 p1-x4 Slots
System Management Bus Header
Standby Power Header
Trusted Platform Module (TPM)/Port 80 Connector
Gigabit Ethernet RJ45 Ports
25GbE SFP28 LAN Ports
Motherboard Mounting Holes
CPU SLOT6 PCIe 4.0 x8
CPU SLOT7 PCIe 4.0 x16
Front Accessible USB 2.0 Headers
Back Panel USB 3.0 Ports
VGA Port
Status
Solid Green: Power On
Solid Red: Overheat
Blinking Red: Power Fail or Fan Fail
Blinking Green: IPMI Normal
Solid Blue: Unit Identified
Unit Identifier Switch
JMD 1: M. 2-H PC Ie 3. x4/ S A 3.0AT
JPG1
JMD 2_SRW 1
MH5
JLAN LED3
JBM 1
MH6
JLAN LED2
JRK 1JIP B1
JPM E2
JMD 2_SRW 2
JWD 1
JPH 1
JPL3JVR M1JSD P4
JSD P1
JSF PLED1
JOPPS
JLAN LED1
USB2/ 3 USB0/ 1 JSM B1
J1
JGP1
I S A3AT
I S A1AT
JSLI M2 JSLI M1
PCIe 3.0 X4
PCIe 3.0 X4
JNS 1F NB
MH2
JPT 1
JRF 1
JD1
JTP M1
JMD 3_SRW 1
JMD 2
JSIM 1
MH4
JST BY1
JSD 1
M.2_ H PCI e 3.0 X2/ S-S A 3. 0AT
FAN A
FAN 4
LED
COM 1
JF1
JMD 3
M.2- H PCI e 3.0 X1
I-SGPI O1CPU SLOT7 PC Ie 4.0 X16
CPU SLOT6 PC Ie 4.0 X8
JPC IE7
JPC IE6
LEDM 1 JMD 1_SRW 1
VGA
LED2
LED3
JUI DB1
LAN3/ 4
JLAN 2 LAN1/ 2
JLAN 1
LAN5/ 6
SFP1
X12SDV-4C-SP6F
DESIGNED IN USA
CPU
REV: 1.10
Intel
i350-AM2
AST2600
MH3
USB4/ 5 (3.0)
IPM I_LAN
JPL2 J SDP3
JSD P2
JPL1
JPW R1
JPI2 C1
JL1
FAN 3
JBT 1
JNV I2C1
JIPM B2
FAN 2 FAN1
MH1
JPV1
BT1
JPF 1
DIM MA2DIM MA1
DIM MB2
DIM MB1
LEDT 2
LEDT 4
LEDT 1
LEDT 3
IPMI LAN
US /5B4
J 2PL
L /2AN1
JPH1
L /4AN3
LED3
J BY1ST
JPME2
F 3AN JNVI2C2
F 4AN
DI 1MMA
DI 2MMB
DI 2MMA
DI 1MMB
JF1
JBT1
US /3B2
JMD2_SRW2
US /1B0
JSD1
J 1PI2C
L /6AN5
J D1SFPLE
SLOT7
MH3
J 1PG
SLOT6
JMD1
JBM1
J SOPP
LED1
F 1AN
COM1
BT1
JS 1MB
I-S A3AT
J M1TP
CPU
JL1
J 1PT
J 1GP
I-S A1AT
J 1PL
LEDM1
LED2
JU DBI 1
VGA
JLANLED3
JSDP2
JSDP3
F 2AN
J R1PW
J 1PV
J 1PF
MH1
JMD3
I- 1SGPIO
F AAN
J M2SLI
JNS1
F BAN
JD1
MH2
MH4
J M1SI
J1
JMD2
JMD3_SRW1
JWD1
J 3PL
JL D2ANLE
JL D1ANLE
JSDP1
JSDP4
JMD2_SRW1
MH5
MH6
JMD1_SRW1
JNVI2C1
JRK1
J 1IPMB
J M1SLI
BMC asswo P rd Label
256Mb SPI Flash with AMI BIOS®
Up to 256GB of ECC and Non-ECC RDIMM/UDIMM DDR4 memory with speeds of up to
2933MHz in four memory slots
Supports an Intel Xeon D-1700 series processor with a thermal design power (TDP) of up to 67W
Note: Please refer to the motherboard specifications pages on our website for updates to
supported processors.
Supports one 2.5" drive of 7mm height
One M.2 PCIe 3.0 p1-x4 or SATA 3.0 slot (M-Key 2280) populated in the connector JMD1
One dedicated IPMI LAN port
Four Gigabit Ethernet ports
Two 25G SFP28 ports
Three connectors (JMD1 populated; JMD2 and JMD3 unpopulated):
JMD1: M.2 PCIe 3.0 p1-x4 or SATA 3.0 slot (M-Key 2280)
JMD2: M.2 PCIe 3.0 p1-x2 or SATA 3.0 or USB 3.0 Slot (B-Key 2280/3042/3052)
JMD3: M.2 PCIe 3.0 p1-x1 or USB 2.0 slot (E-Key 2230)
X12SDV-4C/8C-SP6F
Dimensions: Mini-ITX form factor (6.7" x 6.7") (170.18mm x 170.18mm)
CSE-E302iL
Dimensions: 11.6" x 2.9" x 8.1" (W x H x D) (295 x 73 x 205mm)
Fanless
Processors
BIOS
Memory
Storage Drive
Expansion Slots
Networking
Motherboard
Chassis
System Cooling
Power Supply
180W 12V Lockable DC Power Adapter
1
2
Control Panel Features
Item Features Description
1Power button
2
The main power switch applies or removes primary power from the
power supply to the server but maintains standby power.
To perform most maintenance tasks, unplug the system to remove
all power.
Indicates power is being supplied to the system power supply units.
This LED is illuminated when the system is operating normally.
Indicates hard disk drive activity when flashing.
Power LED &
HDD LED
1 2
3
Rear Chassis Features
Item Features Description
1 Power input
2 I/O ports
The main power switch applies or removes primary power from the power supply
to the server but maintains standby power. To perform most maintenance tasks,
unplug the system to remove all power.
IPMI LAN Port, USB 3.0, GbE LAN, SPF28, VGA
Accepts a standard Kensington cable locking device (not included).3 K-slot for lock
Rear I/O Ports
1
8
9
6
7
4
5
2
3 10
# t n # t nDescrip io Descrip io
1 MI LAN 6 RJ LAN3IP 45
2 U 4 .0) 7 RJ LAN4SB (3 45
3 U 5 .0) 8 LAN5SB (3 SFP28
4 LAN1 9 LAN6RJ45 SFP28
5 LAN2 10 A P tRJ45 VG or

Specyfikacje produktu

Marka: Supermicro
Kategoria: nieskategoryzowany
Model: SuperServer SYS-E302-12D-8C

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Supermicro SuperServer SYS-E302-12D-8C, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje nieskategoryzowany Supermicro

Supermicro

Supermicro SuperStorage 6049P-E1CR45L Instrukcja

21 Sierpnia 2024
Supermicro

Supermicro SuperServer 6028U-E1CNR4T+ Instrukcja

30 Lipca 2024
Supermicro

Supermicro SuperStorage 2029P-E1CR48H Instrukcja

30 Lipca 2024
Supermicro

Supermicro SuperStorage 6049P-E1CR60L Instrukcja

30 Lipca 2024
Supermicro

Supermicro SuperStorage 5049P-E1CR45H Instrukcja

30 Lipca 2024
Supermicro

Supermicro SuperServer SSG-520P-ACTR12H Instrukcja

30 Lipca 2024
Supermicro

Supermicro SuperStorage 6049P-E1CR45L+ Instrukcja

30 Lipca 2024
Supermicro

Supermicro SuperStorage 2029P-E1CR48L Instrukcja

30 Lipca 2024
Supermicro

Supermicro SuperStorage 2029P-DN2R24L Instrukcja

30 Lipca 2024
Supermicro

Supermicro SuperStorage 6029P-E1CR12T Instrukcja

30 Lipca 2024

Instrukcje nieskategoryzowany

Najnowsze instrukcje dla nieskategoryzowany

Asko

Asko DBI644MIB.S.TW/1 Instrukcja

28 Października 2024
Asko

Asko DFS233IB.S.TW/1 Instrukcja

28 Października 2024
Emko

Emko EZM-9920 Instrukcja

27 Października 2024
Emko

Emko ESM-3712-H Instrukcja

27 Października 2024
Emko

Emko ATS-10 Instrukcja

27 Października 2024
Emko

Emko EAOM-11.2 Instrukcja

27 Października 2024
Emko

Emko EPM-3790 Instrukcja

27 Października 2024
Emko

Emko EPM-7790 Instrukcja

27 Października 2024
Livarno Lux

Livarno Lux IAN 108340 Instrukcja

27 Października 2024
Livarno Lux

Livarno Lux HG06009A-BS Instrukcja

27 Października 2024