Instrukcja obsługi Supermicro SuperServer 5028L-TN2

Supermicro nieskategoryzowany SuperServer 5028L-TN2

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Supermicro SuperServer 5028L-TN2 (120 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/120

USER’S MANUAL

Revision 1.0

S SUPER ERVER®

5028L-TN2

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.

The vendor assumes no responsibility for any inaccuracies that may be contained in this document,

makes no commitment to update or to keep current the information in this manual, or to notify any

person or organization of the updates. Please Note: For the most up-to-date version of this

manual, please see our web site at www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product

described in this manual at any time and without notice. This product, including software and

documentation, is the property of Supermicro and/or its licensors, and is supplied only under a

license. Any use or reproduction of this product is not allowed, except as expressly permitted by

the terms of said license.

IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,

SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO

USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY

HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE

COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH

HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa

Clara County in the State of California, USA. The State of California, County of Santa Clara shall

be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all

claims will not exceed the price paid for the hardware product.

FCC Statement: This equipment has been tested and found to comply with the limits for a Class

A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the manufacturer’s instruction manual, may cause harmful

interference with radio communications. Operation of this equipment in a residential area is likely

to cause harmful interference, in which case you will be required to correct the interference at your

own expense.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate

warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate

Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”

WARNING: Handling of lead solder materials used in this

product may expose you to lead, a chemical known to

the State of California to cause birth defects and other

reproductive harm.

Manual Revision 1.0

Release Date: September 10, 2015

Unless you request and receive written permission from Super Micro Computer, Inc., you may not

copy any part of this document.

Information in this document is subject to change without notice. Other products and companies

referred to herein are trademarks or registered trademarks of their respective companies or mark

holders.

Printed in the United States of America

Preface

About this Manual

This manual is written for professional system integrators and PC technicians. It

provides information for the installation and use of the SuperServer. Installation and

maintainance should be performed by experienced technicians only.

Please refer to the server specications page on our Web site for updates on

supported memory, processors and operating systems (www.supermicro.com).

This manual may be periodically updated without notice. Please check the

Supermicro Web site for possible updates to the manual revision level.

Warnings

Special attention should be given to the following symbols used in this manual.

Warning! Indicates high voltage may be encountered when performing

a procedure.

Warning! Indicates important information given to prevent equipment/

property damage or personal injury.

S SUPER ERVER 5028L-TN2 Manual

Contents

Chapter 1 Introduction ..............................................................................1-1

1-1 Overview ......................................................................................................... 1-1

1-2 Motherboard Features ..................................................................................... 1-2

Processors 1-2 ......................................................................................................

Memory 1-2 ...........................................................................................................

Serial ATA ........................................................................................................ 1-2

PCI Expansion Slots ....................................................................................... 1-2

Input/Output Ports ........................................................................................... 1-2

1-3 Chassis Features ............................................................................................ 1-4

System Power ................................................................................................. 1-4

Drives 1-4 ..............................................................................................................

PCI Slots ......................................................................................................... 1-4

Control Panel .................................................................................................. 1-4

Cooling System ............................................................................................... 1-4

1-4 Contacting Supermicro .................................................................................... 1-5

Chapter 2 System Interface

2-1 Overview ........................................................................................................ 2-1

2-2 Control Panel Buttons ..................................................................................... 2-2

2-3 Control Panel LEDs ........................................................................................ 2-2

Overheating 2-3 .....................................................................................................

Overheat Temperature Setting ................................................................... 2-3

Responses 2-3 ..................................................................................................

Chapter 3 Standardized Warning Statements for AC Systems

About Standardized Warning Statements ....................................................... 3-1

Warning Denition ........................................................................................... 3-1

Installation Instructions .................................................................................... 3-4

Circuit Breaker ................................................................................................ 3-5

Power Disconnection Warning ........................................................................ 3-6

Equipment Installation ..................................................................................... 3-8

Restricted Area ................................................................................................ 3-9

Battery Handling ............................................................................................ 3-10

Redundant Power Supplies (if applicable to your system) ........................... 3-12

Backplane Voltage (if applicable to your system) ......................................... 3-13

Comply with Local and National Electrical Codes ........................................ 3-14

Product Disposal ........................................................................................... 3-15

Hot Swap Fan Warning (if applicable to your system) ................................. 3-16

Power Cable and AC Adapter ...................................................................... 3-18

Preface

Chapter 4 Advanced Motherboard Setup

4-1 Handling the Motherboard .............................................................................. 4-1

Precautions 4-1 .....................................................................................................

Unpacking 4-1 .......................................................................................................

4-2 Processor Installation ...................................................................................... 4-2

4-3 CPU Heatsink Installation ............................................................................... 4-4

4-4 Installing Memory ............................................................................................ 4-6

Memory Support .............................................................................................. 4-6

4-5 Connecting Cables .......................................................................................... 4-8

Connecting Data Cables ................................................................................. 4-8

Connecting the Power Button ......................................................................... 4-8

4-6 Rear I/O Ports ................................................................................................. 4-9

4-7 Motherboard Details ...................................................................................... 4-10

4-8 Connector Denitions .................................................................................... 4-12

Power Button (JF1) ....................................................................................... 4-14

4-9 Jumper Settings ............................................................................................ 4-19

Explanation of Jumpers ................................................................................ 4-19

CMOS Clear .................................................................................................. 4-19

4-10 Onboard Indicators ........................................................................................ 4-22

4-11 Serial ATA and HDD Connections ................................................................. 4-23

4-12 Installing Software ......................................................................................... 4-24

SuperDoctor III .............................................................................................. 4-25

4-13 Onboard Battery ............................................................................................ 4-27

Chapter 5 Advanced Chassis Setup and Maintenance ........................ 5-1

5-1 Removing Power from the System ................................................................. 5-2

5-2 Hardware Security ......................................................................................... 5-2

Front Bezel Lock ............................................................................................. 5-2

Rear Chassis Hasp ......................................................................................... 5-3

Kensington Cable Slot (K-Slot) ....................................................................... 5-3

5-3 Removing the Chassis Cover ......................................................................... 5-4

5-4 Removing and Installing Drives ...................................................................... 5-5

Front Mounted Hot-Swap Drives..................................................................... 5-5

Installing the Internal Fixed Hard Drives......................................................... 5-8

Installing the Side Mounted Fixed Hard Drive ................................................ 5-9

5-5 Installing the DVD Drive ................................................................................ 5-10

5-6 Installing Expansion Cards ........................................................................... 5-12

5-7 Installing the Rear Exhaust Fan ................................................................... 5-14

5-8 Replacing the Power Supply ....................................................................... 5-15

5-9 Replacing the Backplane ............................................................................. 5-16

S SUPER ERVER 5028L-TN2 Manual

Chapter 6 BIOS

6-1 Introduction ...................................................................................................... 6-1

Starting BIOS Setup Utility .............................................................................. 6-1

How To Change the Conguration Data ......................................................... 6-1

How to Start the Setup Utility ......................................................................... 6-2

6-2 Main Setup ...................................................................................................... 6-2

6-3 Advanced Setup Congurations...................................................................... 6-4

6-4 Event Logs .................................................................................................... 6-25

6-5 Boot Settings ................................................................................................. 6-26

6-6 Security Settings ........................................................................................... 6-28

6-7 Save & Exit ................................................................................................... 6-29

Appendix A BIOS Error Beep Codes ..................................................... A-1

Appendix B UEFI BIOS Recovery Instructions .................................... B-1

Appendix C System Specications ........................................................ C-1

Chapter 1

Introduction

1-1 Overview

The SuperServer 5028L-TN2 is a cloud-base edge server comprised of two main

subsystems: the SC721TQ-250B mini-tower chassis and the X10SLV-Q single

processor motherboard. It is designed for le back up and synchronizing solutions.

It is also well-suited for space-efcient compact design, NAS Servers, SOHO Entry-

Level Server and Embedded Applications. Refer to the Supermicro web site for

information on operating systems that have been certied for use with the system

(www.supermicro.com).

The 5028L-TN2 Super Server

In addition to the above components, the server includes:

• One SAS/SATA backplane (CSE-SAS-733TQ-O-P)

• Cooling: One 12-cm fan (FAN-0124L4)

• Rear I/O panel: (MCP-260-00070)

• Four hard drive carriers (MCP-220-00075-0B)

Note: For your system to work properly, please follow the links below to download

all necessary drivers/utilities and the user’s manual for your server.

• Supermicro product manuals: http://www.supermicro.com/support/manuals/

• Product drivers and utilities: ftp://ftp.supermicro.com

• Product safety info:

http://www.supermicro.com/about/policies/safety_information.cfm

For support, email support@supermicro.com.

Chapter 1: Introduction

1-1

1-2

S SUPER ERVER 5028L-TN2 User's Manual

1-2 Motherboard Features

The server is built around the X10SLV-Q, a single processor motherboard based on

the Intel Q87 chipset. Below are the main features. Figure 1-1 is a block diagram

of the chipset.

Processors

The X10SLV-Q supports a single 4th Generation Intel Core i7, i5, i3, Pentium/Celeron

processor. Refer to the web site for a complete listing of supported processors (www.

supermicro.com).

Memory

The board has two DIMM slots that can support up to 16GB of Non-ECC DDR3

SODIMM up to 1600MHz memory.

Serial ATA

A SATA controller is also integrated into the chipset to provide two SATA 3.0 (mSATA)

and two SATA 2.0 ports.

PCI Expansion Slots

The system has one mini PCIe slot, full and half card with mSATA support.

Input/Output Ports

The I/O ports on the chassis include:

One DVI-I One HDMI

One DP Two GbE LAN

Two USB 3.0 Two USB 2.0

Two COM One Audio

1-3

Chapter 1: Introduction

Figure 1-1. System Block Diagram

Note: This is a general block diagram. See Chapter 4 for details.

1600 1333 1066/ / MHz

2 X U 3.0 R rSB ea

5G sbp

USB3.0

V .5RD12

INTEL LGA1150

PCIe x SLOT16 5.0GT/s

SVID

VRM .512

DDR CH3 ( A) DI A1MM

DDR CHB3 ( ) DI B1MM

1600 1333 1066/ / MHz

5GT/s

x4 DMI

S r with m TAha ed SA

SATA- I II

2 X U 2.0 R RSB EA

6Gb/s

480 bpM s

USB2.0

SATA- III

RJ45

2.5G sT/

PCI . x1 GLAN1e2 0_

I V217

PCH

Intel

H81 / Q87

(So et-H3)ck

2.7 Gb/s

x2 FDI

AZALIA

R ltek ALC S-VD2ea 888

RJ45

2.5G sT/

PCI . x1 GLAN2e2 0_

I -AT210

Mini PCI-E SLOT

PCI . x1e2 0_

5G sT/

BLO DIAGRAMCK

RoHS 6/6

FL HAS

SPI Mb128

SPI

Display Port

HDMI

DVI-I Digital r Bpo t

Digital r Cpo t

Digital r Dpo t

TPM1.2 H reade

LPC

HWM

COM1/2 R rea

NCT D6106

LPC I/O

SODIMM

PCIE[3]

PCIE[4]

PCIE[2]

SATA[0/1]

SATA[0]

3Gb/s

SATA[4/5]

Note: I-SATA0 ct n e whe m-SATA n Fun io disabl d i serted .

DDI B

DDI C

DDI D

RGB

USB[0/1]

USB[2/3]

2 X U 2.0 Fr tSB on

480 bpM s

USB2.0

USB[4/5]

6Gb/s

COM 3/4/5 H reade

1 X U A-typeSB

480 bpM s

USB2.0

USB[10]

Note: COM5 su rt RSppo

485/

GPIO

Ex rpande

USB[11]

Express

PCI . x16e3 0_

8.0GT/s

)

X10SLV-Q

Q87

2 X SATA-III

1-4

S SUPER ERVER 5028L-TN2 User's Manual

1-3 Chassis Features

The SuperServer 5028L-TN2 is built on the SC721TQ-250B, a compact mini-tower

chassis. It has a hinged front cover that hides the storage drives and control panel.

The following is a general outline of the main features.

System Power

The system has a single 250W Flex ATX Multi-output AC-DC power supply (part

number PWS-251-1H). It has Bronze level certication from 80 Plus.

Drives

The chassis supports up to four 3.5" hot-swap SAS/SATA drives and two 2.5" xed

internal drives. The internal drives are not hot-swappable. The drives are supported

by a SATA/SAS backplane with SES2.

It also supports one slim DVD drive.

PCI Slots

The chassis includes a slot for one low-prole PCI-E expansion card.

Control Panel

The control panel provides system monitoring and power control. LEDs indicate

power on, network activity, hard disk drive activity and system overheat. The control

panel also includes a main power button and a reset button.

Cooling System

The chassis has one 9cm rear fan with 25db whisper quiet operation, and an

optional 8cm front fan.

1-5

Chapter 1: Introduction

1-4 Contacting Supermicro

Headquarters

Address: Super Micro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.

Tel: +1 (408) 503-8000

Fax: +1 (408) 503-8008

Email: marketing@supermicro.com (General Information)

support@supermicro.com (Technical Support)

Web Site: www.supermicro.com

Europe

Address: Super Micro Computer B.V.

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands

Tel: +31 (0) 73-6400390

Fax: +31 (0) 73-6416525

Email: sales@supermicro.nl (General Information)

support@supermicro.nl (Technical Support)

rma@supermicro.nl (Customer Support)

Web Site: www.supermicro.nl

Asia-Pacic

Address: Super Micro Computer, Inc.

3F, No. 150, Jian 1st Rd.

Zhonghe Dist., New Taipei City 235

Taiwan (R.O.C)

Tel: +886-(2) 8226-3990

Fax: +886-(2) 8226-3992

Email: support@supermicro.com.tw

Web Site: www.supermicro.com.tw

1-6

S SUPER ERVER 5028L-TN2 User's Manual

Notes

2-1

Chapter 2 System Interface

Chapter 2

System Interface

2-1 Overview

The chassis includes a control panel on the front that includes power buttons and

status monitoring lights.

Figure 2-1. Control Panel

Power

Button

Reset

Button

LEDs

SUPERSERVER 5028L-TN2 User's Manual

2-2

2-3 Control Panel LEDs

There are four LEDs that provide status information about the system.

Power

The main power switch applies or removes primary power from the power supply

to the server but maintains standby power. To perform most maintenance tasks,

unplug the system to remove all power.

Reset

The reset button is used to reboot the system.

2-2 Control Panel Buttons

The chassis includes two push-buttons that control power to the system.

Power

Indicates power is being supplied to the system power supply units. This LED is

illuminated when the system is operating normally.

HDD

Indicates activity on the hard disk drive when ashing.

2-3

Chapter 2 System Interface

Information LED

Alerts operator to several states, as noted in the table below.

Information LED

Status Description

Continuously on and red An overheat condition has occured.

(This may be caused by cable congestion.)

Blinking red (1Hz) Fan failure, check for an inoperative fan.

Blinking red (0.25Hz) Power failure, check for a non-operational power supply.

Solid blue Local UID has been activated. Use this function to locate

the server in a rack mount environment.

Blinking blue Remote UID is on. Use this function to identify the

server from a remote location.

NIC

Indicates network activity when ashing.

Overheating

There are several possible responses if the system overheats.

Overheat Temperature Setting

Some backplanes allow the overheat temperature to be set at 45, 50, or 55 degrees

by changing a jumper setting. For more information, consult the backplane user

manual on the Supermicro website.

Responses

1. Use the LEDs to determine the nature of the overheating condition.

2. Conrm that the chassis covers are installed properly.

3. Check the routing of the cables and make sure all fans are present and operating

normally.

4. Verify that the heatsinks are installed properly.

SUPERSERVER 5028L-TN2 User's Manual

2-4

Notes

3-1

Chapter 3: Warning Statements for AC Systems

Chapter 3

Standardized Warning Statements for AC Systems

About Standardized Warning Statements

The following statements are industry standard warnings, provided to warn the user

of situations which have the potential for bodily injury. Should you have questions

or experience difficulty, contact Supermicro's Technical Support department

for assistance. Only certied technicians should attempt to install or congure

components.

Read this chapter in its entirety before installing or conguring components in the

Supermicro chassis. Some warnings may not apply for your system.

These warnings may also be found on our web site at http://www.supermicro.com/

about/policies/safety_information.cfm.

Warning!

This warning symbol means danger. You are in a situation that could cause bodily

injury. Before you work on any equipment, be aware of the hazards involved with

electrical circuitry and be familiar with standard practices for preventing accidents.

Warning Denition

警告の定義

この警告サインは危険を意味します。

人身事故につながる可能性がありますので、いずれの機器でも動作させる前に、

電気回路に含まれる危険性に注意して、標準的な事故防止策に精通して下さい。

此警告符号代表危险。

您正处于可能受到严重伤害的工作环境中。在您使用设备开始工作之前，必须充分

意识到触电的危险，并熟练掌握防止事故发生的标准工作程序。请根据每项警告结

尾的声明号码找到此设备的安全性警告说明的翻译文本。

此警告符號代表危險。

您正處於可能身體可能會受損傷的工作環境中。在您使用任何設備之前，請注意觸

電的危險，並且要熟悉預防事故發生的標準工作程序。請依照每一注意事項後的號

碼找到相關的翻譯說明內容。

3-2

SUPERSERVER 5028L-TN2 User's Manual

Warnung

WICHTIGE SICHERHEITSHINWEISE

Dieses Warnsymbol bedeutet Gefahr. Sie benden sich in einer Situation, die zu

Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den

Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung

vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen

Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten

Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.

BEWAHREN SIE DIESE HINWEISE GUT AUF.

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes

de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y

familiarícese con los procedimientos estándar de prevención de accidentes. Al

nal de cada advertencia encontrará el número que le ayudará a encontrar el texto

traducido en el apartado de traducciones que acompaña a este dispositivo.

GUARDE ESTAS INSTRUCCIONES.

IMPORTANTES INFORMATIONS DE SÉCURITÉ

Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une

situation pouvant entraîner des blessures ou des dommages corporels. Avant

de travailler sur un équipement, soyez conscient des dangers liés aux circuits

électriques et familiarisez-vous avec les procédures couramment utilisées pour

éviter les accidents. Pour prendre connaissance des traductions des avertissements

gurant dans les consignes de sécurité traduites qui accompagnent cet appareil,

référez-vous au numéro de l'instruction situé à la n de chaque avertissement.

CONSERVEZ CES INFORMATIONS.

ןונקת תורהצהאהרהז

ןה תואבה תורהצהא ינפמ שמתשמה תא ריהזהל תנמ לע ,היישעתה ינקת יפ לע תורהז הלבח

ה וא תולאש שיו הדימב .תירשפא תיזיפי ,יהשלכ היעבב תולקתרוציל שי הכימת תקלחמ םע רשק

רידגהל וא ןיקתהל םיאשר דבלב םיכמסומ םיאנכט .ורקימרפוס לש תינכט תאה .םיביכר

אורקל שי .ורקימרפוס יזראמב םיביכרה תרדגה וא תנקתה ינפל ואולמב חפסנה תא

3-3

Chapter 3: Warning Statements for AC Systems

3-3

안전을 위한 주의사항

경고!

이 경고 기호는 위험이 있음을 알려 줍니다. 작업자의 신체에 부상을 야기 할 수

있는 상태에 있게 됩니다. 모든 장비에 대한 작업을 수행하기 전에 전기회로와

관련된 위험요소들을 확인하시고 사전에 사고를 방지할 수 있도록 표준

작업절차를 준수해 주시기 바랍니다.

해당 번역문을 찾기 위해 각 경고의 마지막 부분에 제공된 경고문 번호를

참조하십시오

BELANGRIJKE VEILIGHEIDSINSTRUCTIES

Dit waarschuwings symbool betekent gevaar. U verkeert in een situatie die

lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken,

dient u zich bewust te zijn van de bij een elektrische installatie betrokken risico's

en dient u op de hoogte te zijn van de standaard procedures om ongelukken te

voorkomen. Gebruik de nummers aan het eind van elke waarschuwing om deze te

herleiden naar de desbetreffende locatie.

BEWAAR DEZE INSTRUCTIES

.   !









3-4

SUPERSERVER 5028L-TN2 User's Manual

Installation Instructions

Warning!

Read the installation instructions before connecting the system to the power source.

Warnung

Vor dem Anschließen des Systems an die Stromquelle die Installationsanweisungen

lesen.

¡Advertencia!

Lea las instrucciones de instalación antes de conectar el sistema a la red de

alimentación.

Attention

Avant de brancher le système sur la source d'alimentation, consulter les directives

d'installation.

設置手順書

システムを電源に接続する前に、設置手順書をお読み下さい。



אורקל שי רוקמל תכרעמה רוביח ינפל הנקתה תוארוה תאחתמ.

시스템을 전원에 연결하기 전에 설치 안내를 읽어주십시오.

Waarschuwing

Raadpleeg de installatie-instructies voordat u het systeem op de voedingsbron

aansluit.

警告

将此系统连接电源前,请先阅读安装说明。

警告

將系統與電源連接前，請先閱讀安裝說明。

3-5

Chapter 3: Warning Statements for AC Systems

Circuit Breaker

Warning!

This product relies on the building's installation for short-circuit (overcurrent)

protection. Ensure that the protective device is rated not greater than: 250 V, 20 A.

サーキット・ブレーカー

この製品は、短絡（過電流）保護装置がある建物での設置を前提としています。

保護装置の定格が250 V、20 Aを超えないことを確認下さい。

Warnung

Dieses Produkt ist darauf angewiesen, dass im Gebäude ein Kurzschluss-

bzw. Überstromschutz installiert ist. Stellen Sie sicher, dass der Nennwert der

Schutzvorrichtung nicht mehr als: 250 V, 20 A beträgt.

¡Advertencia!

Este equipo utiliza el sistema de protección contra cortocircuitos (o sobrecorrientes)

del edicio. Asegúrese de que el dispositivo de protección no sea superior a: 250

V, 20 A.

Attention

Pour ce qui est de la protection contre les courts-circuits (surtension), ce produit

dépend de l'installation électrique du local. Vériez que le courant nominal du

dispositif de protection n'est pas supérieur à :250 V, 20 A.

לע ךמתסמ הז רצומנגהה תעינמל םינבמב תנקתומה יכ אדוול שי .ילמשח רצק

רצקה ינפמ ןגמה רישכמה ילמשחהמ רתוי אל אוה-250 V, 20 A





20 250A, V : 

警告

此产品的短路(过载电流)保护由建筑物的供电系统提供,确保短路保护设备的额定电

流不大于250V,20A。

警告

此產品的短路(過載電流)保護由建築物的供電系統提供,確保短路保護設備的額定電

流不大於250V,20A。

3-6

SUPERSERVER 5028L-TN2 User's Manual

Power Disconnection Warning

電源切断の警告

システムコンポーネントの取り付けまたは取り外しのために、シャーシー内部にアクセス

するには、

システムの電源はすべてのソースから切断され、電源コードは電源モジュールから取り

外す必要があります。

警告

在你打开机箱并安装或移除内部器件前,必须将系统完全断电,并移除电源线。

警告

在您打開機殼安裝或移除內部元件前，必須將系統完全斷電，並移除電源線。

Warnung

Das System muss von allen Quellen der Energie und vom Netzanschlusskabel

getrennt sein, das von den Spg.Versorgungsteilmodulen entfernt wird, bevor es

auf den Chassisinnenraum zurückgreift, um Systemsbestandteile anzubringen oder

zu entfernen.

Warning!

The system must be disconnected from all sources of power and the power cord

removed from the power supply module(s) before accessing the chassis interior to

install or remove system components.

!

   ()     

.    250V(), 20A() 

  .

Waarschuwing

Dit product is afhankelijk van de kortsluitbeveiliging (overspanning) van

uw electrische installatie. Controleer of het beveiligde aparaat niet groter

gedimensioneerd is dan 220V, 20A.

3-10

SUPERSERVER 5028L-TN2 User's Manual

Battery Handling

Warning!

There is the danger of explosion if the battery is replaced incorrectly. Replace the

battery only with the same or equivalent type recommended by the manufacturer.

Dispose of used batteries according to the manufacturer's instructions

תלבגומ השיג םע רוזא

!הרהזא

תרזעב תנתינ השיגה .השיג תלבגה םהב שיש םירוזאב הדיחיה תא ןיקתהל שי

.)'דכו לוענמ ,חתפמ( דבלב החטבא ילכ

.  



 

경고!

이 장치는 접근이 제한된 구역에 설치하도록 되어있습니다. 특수도구, 잠금 장치

및 키, 또는 기타 보안 수단을 통해서만 접근 제한 구역에 들어갈 수 있습니다.

Waarschuwing

Dit apparaat is bedoeld voor installatie in gebieden met een beperkte toegang.

Toegang tot dergelijke gebieden kunnen alleen verkregen worden door gebruik te

maken van speciaal gereedschap, slot en sleutel of andere veiligheidsmaatregelen.

電池の取り扱い

電池交換が正しく行われなかった場合、破裂の危険性があります。交換する電池はメー

カーが推奨する型、または同等のものを使用下さい。使用済電池は製造元の指示に従

って処分して下さい。

警告

电池更换不当会有爆炸危险。请只使用同类电池或制造商推荐的功能相当的电池更

换原有电池。请按制造商的说明处理废旧电池。

警告

電池更換不當會有爆炸危險。請使用製造商建議之相同或功能相當的電池更換原有

電池。請按照製造商的說明指示處理廢棄舊電池。

3-11

Chapter 3: Warning Statements for AC Systems

Warnung

Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die

Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp.

Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers.

Attention

Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer

que par une pile de type semblable ou équivalent, recommandée par le fabricant.

Jeter les piles usagées conformément aux instructions du fabricant.

¡Advertencia!

Existe peligro de explosión si la batería se reemplaza de manera incorrecta.

Reemplazar la batería exclusivamente con el mismo tipo o el equivalente

recomendado por el fabricante. Desechar las baterías gastadas según las

instrucciones del fabricante.

!הרהזא

תנכס תמייקץוציפ .הניקת אל ךרדב הפלחוהו הדימב הללוסה לש ףילחהל שי

גוסב הללוסה תא מ םאותה תרבחלמומ ןרציתצ.

תוללוסה קוליס תושמושמה עצבל שי .ןרציה תוארוה יפל









경고!

배터리가 올바르게 교체되지 않으면 폭발의 위험이 있습니다. 기존 배터리와

동일하거나 제조사에서 권장하는 동등한 종류의 배터리로만 교체해야 합니다.

제조사의 안내에 따라 사용된 배터리를 처리하여 주십시오.

Waarschuwing

Er is ontplofngsgevaar indien de batterij verkeerd vervangen wordt. Vervang de

batterij slechts met hetzelfde of een equivalent type die door de fabrikant aanbevolen

wordt. Gebruikte batterijen dienen overeenkomstig fabrieksvoorschriften afgevoerd

te worden.

3-12

SUPERSERVER 5028L-TN2 User's Manual

Warnung

Dieses Gerät kann mehr als eine Stromzufuhr haben. Um sicherzustellen, dass

der Einheit kein trom zugeführt wird, müssen alle Verbindungen entfernt werden.

¡Advertencia!

Puede que esta unidad tenga más de una conexión para fuentes de alimentación.

Para cortar por completo el suministro de energía, deben desconectarse todas las

conexiones.

Attention

Cette unité peut avoir plus d'une connexion d'alimentation. Pour supprimer toute

tension et tout courant électrique de l'unité, toutes les connexions d'alimentation

doivent être débranchées.

Redundant Power Supplies (if applicable to your system)

Warning!

This unit might have more than one power supply connection. All connections must

be removed to de-energize the unit.

冗長電源装置

このユニットは複数の電源装置が接続されている場合があります。

ユニットの電源を切るためには、すべての接続を取り外さなければなりません。

דחא קפסמ רתוי םייק םא

!הרהזא

.קפס לש דחא רוביחמ רתוי שי הדחיל תא ריסהל שי

ןקורל תנמ לע םירוביחה לכ

חיה תאי.הד

警告

此部件连接的电源可能不止一个，必须将所有电源断开才能停止给该部件供电。

警告

此裝置連接的電源可能不只一個，必須切斷所有電源才能停止對該裝置的供電。

Note: Not applicable to this system.

3-13

Chapter 3: Warning Statements for AC Systems

Backplane Voltage (if applicable to your system)

バックプレーンの電圧

システムの稼働中は危険な電圧または電力が、バックプレーン上にかかっています。

修理する際には注意ください。

警告

当系统正在进行时，背板上有很危险的电压或能量，进行维修时务必小心。

警告

當系統正在進行時，背板上有危險的電壓或能量，進行維修時務必小心。

Warnung

Wenn das System in Betrieb ist, treten auf der Rückwandplatine gefährliche

Spannungen oder Energien auf. Vorsicht bei der Wartung.

¡Advertencia!

Cuando el sistema está en funcionamiento, el voltaje del plano trasero es peligroso.

Tenga cuidado cuando lo revise.

Attention

Lorsque le système est en fonctionnement, des tensions électriques circulent sur

le fond de panier. Prendre des précautions lors de la maintenance.

Warning!

Hazardous voltage or energy is present on the backplane when the system is

operating. Use caution when servicing.

.



경고!

이 장치에는 한 개 이상의 전원 공급 단자가 연결되어 있을 수 있습니다. 이

장치에 전원을 차단하기 위해서는 모든 연결 단자를 제거해야만 합니다.

Waarschuwing

Deze eenheid kan meer dan één stroomtoevoeraansluiting bevatten. Alle

aansluitingen dienen verwijderd te worden om het apparaat stroomloos te maken.

3-15

Chapter 3: Warning Statements for AC Systems

Product Disposal

Warning!

Ultimate disposal of this product should be handled according to all national laws

and regulations.

יצראה למשחה יקוח םואית

!הרהזא

תנקתה םייצראהו םיימוקמה למשחה יקוחל תמאות תויהל תבייח דויצה.





Attention

L'équipement doit être installé conformément aux normes électriques nationales

et locales.

경고!

현 지역 및 국가의 전기 규정에 따라 장비를 설치해야 합니다.

Waarschuwing

Bij installatie van de apparatuur moet worden voldaan aan de lokale en nationale

elektriciteitsvoorschriften.

製品の廃棄

この製品を廃棄処分する場合、国の関係する全ての法律・条例に従い処理する必要が

あります。

警告

本产品的废弃处理应根据所有国家的法律和规章进行。

警告

本產品的廢棄處理應根據所有國家的法律和規章進行。

Warnung

Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen

des Landes erfolgen.

3-16

SUPERSERVER 5028L-TN2 User's Manual

Waarschuwing

De uiteindelijke verwijdering van dit product dient te geschieden in overeenstemming

met alle nationale wetten en reglementen.

¡Advertencia!

Al deshacerse por completo de este producto debe seguir todas las leyes y

reglamentos nacionales.

Attention

La mise au rebut ou le recyclage de ce produit sont généralement soumis à des

lois et/ou directives de respect de l'environnement. Renseignez-vous auprès de

l'organisme compétent.

Warning!

The fans might still be turning when you remove the fan assembly from the chassis.

Keep ngers, screwdrivers, and other objects away from the openings in the fan

assembly's housing.

Hot Swap Fan Warning (if applicable to your system)

רצומה קוליס

!הרהזא

ו תויחנהל םאתהב תויהל בייח הז רצומ לש יפוס קוליס.הנידמה יקוח

 

ファン・ホットスワップの警告

シャーシから冷却ファン装置を取り外した際、ファンがまだ回転している可能性がありま

す。ファンの開口部に、指、ドライバー、およびその他のものを近づけないで下さい。

警告

当您从机架移除风扇装置，风扇可能仍在转动。小心不要将手指、螺丝起子和其他

物品太靠近风扇

경고!

이 제품은 해당 국가의 관련 법규 및 규정에 따라 폐기되어야 합니다.

Note: Not applicable to this system.

3-18

SUPERSERVER 5028L-TN2 User's Manual

Warning!

When installing the product, use the provided or designated connection cables,

power cables and AC adaptors. Using any other cables and adaptors could cause

a malfunction or a re. Electrical Appliance and Material Safety Law prohibits the

use of UL or CSA -certied cables (that have UL/CSA shown on the code) for any

other electrical devices than products designated by Supermicro only.

Power Cable and AC Adapter

Warnung

Bei der Installation des Produkts, die zur Verfügung gestellten oder benannt

Anschlusskabel, Stromkabel und Netzteile. Verwendung anderer Kabel und Adapter

kann zu einer Fehlfunktion oder ein Brand entstehen. Elektrische Geräte und

Material Safety Law verbietet die Verwendung von UL-oder CSA-zertizierte Kabel,

UL oder CSA auf der Code für alle anderen elektrischen Geräte als Produkte von

Supermicro nur bezeichnet gezeigt haben.

¡Advertencia!

Al instalar el producto, utilice los cables de conexión previstos o designados, los

cables y adaptadores de CA. La utilización de otros cables y adaptadores podría

ocasionar un mal funcionamiento o un incendio. Aparatos Eléctricos y la Ley de

Seguridad del Material prohíbe el uso de UL o CSA cables certicados que tienen

UL o CSA se muestra en el código de otros dispositivos eléctricos que los productos

designados por Supermicro solamente.

電源コードとACアダプター

製品を設置する場合、提供または指定された接続ケーブル、電源コードとACアダプター

を使用下さい。他のケーブルやアダプタを使用すると故障や火災の原因になることがあ

ります。電気用品安全法は、ULまたはCSA認定のケーブル(UL/CSEマークがコードに表

記)を Supermicroが指定する製品以外に使用することを禁止しています。

警告

安装此产品时,请使用本身提供的或指定的连接线,电源线和电源适配器.使用其它线

材或适配器可能会引起故障或火灾。除了Supermicro所指定的产品,电气用品和材料

安全法律规定禁止使用未经UL或CSA认证的线材。(线材上会显示UL/CSA符号)。

警告

安裝此產品時,請使用本身提供的或指定的連接線,電源線和電源適配器.使用其它線

材或適配器可能會引起故障或火災。除了Supermicro所指定的產品,電氣用品和材料

安全法律規定禁止使用未經UL或CSA認證的線材。(線材上會顯示UL/CSA符號)。

Specyfikacje produktu

Marka:	Supermicro
Kategoria:	nieskategoryzowany
Model:	SuperServer 5028L-TN2
Kolor produktu:	Czarny
Częstotliwość wejściowa AC:	50 - 60 Hz
Napięcie wejściowe AC:	100 - 240 V
Wysokość produktu:	240 mm
Szerokość produktu:	210 mm
Głębokość produktu:	279 mm
Waga produktu:	6800 g
Certyfikat środowiskowy (zrównoważonego rozwoju):	RoHS
Prędkość transferu danych przez Ethernet LAN:	10,100,1000 Mbit/s
Ilość portów Ethernet LAN (RJ-45):	2
Zakres temperatur (eksploatacja):	0 - 40 °C
Zakres wilgotności względnej:	10 - 85 %
Typ procesora:	Intel
Liczba portów USB 2.0:	5
Przewodowa sieć LAN:	Tak
Diody LED:	Tak
Zakres temperatur (przechowywanie):	-20 - 60 °C
Dopuszczalna wilgotność względna:	10 - 95 %
Ilość obsługiwanych rozmiarów dysków pamięci:	4
Obsługiwane rozmiary dysków pamięci:	3.5 "
Ilość portów USB 3.2 Gen 1 (3.1 Gen 1) Typu-A:	2
Obsługiwane rodzaje pamięci:	DDR3-SDRAM
Bez kody korekcyjnego:	Tak
Maksymalna pojemność pamięci:	16 GB
Gniazdo procesora:	LGA 1150 (Socket H3)
Procesor:	Intel® Pentium®
Poziomy raid:	0, 1,5, 10
Typ BIOS:	EEPROM
PCI Express x16 gniazda:	1
Zasilanie:	250 W
Wspierane interfejsy dysków twardych:	Serial ATA III
Rodzaj interfejsu sieci Ethernet:	Fast Ethernet, Gigabit Ethernet
Kontroler LAN:	Intel I210-AT, Intel I217
Rozmiar pamięci BIOS:	128 Mbit
Wersja ACPI:	4.0
Model karty graficznej on-board:	Aspeed AST2400
Wersja gniazd typu Slot (PCI Express):	3.0
Rodzaj pamięci:	204-pin SO-DIMM
Napięcie pamięci:	1.35, 1.5 V
Ilość slotów DIMM:	2
Liczba obsługiwanych procesorów:	1
Przemieszczanie twardej wnęki na napęd HDD:	Tak
Funkcje BIOS:	APM 1.2, Plug & Play, UEFI