Instrukcja obsługi Sun Joe CJ602E
Sun Joe
łuparka do drewna
CJ602E
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Sun Joe CJ602E (48 stron) w kategorii łuparka do drewna. Ta instrukcja była pomocna dla 11 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/48
© 2020 by Snow Joe
®, LLC
All rights reserved. Original instructions. SAVE THESE INSTRUCTIONS
1
EN
A Division of Snow Joe
®, LLC
R
OPERATOR’S MANUAL
Model CJ602E Form No. SJ-CJ602E-880E-MR5
ELECTRIC WOOD CHIPPER + SHREDDER
15-AMP | 17:1 REDUCTION RATIO
IMPORTANT!
Safety Instructions
All Operators Must Read These
Instructions Before Use
Always follow these safety guidelines. Failure to do so may
result in serious bodily injury or death.
General Safety WARNINGS!
You and any other operator of this wood chipper + shredder
must read, understand, and follow these instructions in
their entirety. Failure to follow these instructions may result
in , and/or serious ELECTRIC SHOCK, FIRE PERSONAL
INJURY.
Notice the personal safety alert symbol m used in this
manual to draw your attention to a given along WARNING
with the particular operating instruction. This means that
the operation requires special ATTENTION, CAUTION, and
AWARENESS.
mWARNING! Wear appropriate personal hearing
protection during use. Under some conditions and duration of
use, noise from this product may contribute to hearing loss.
mWARNING! The rotating blades can cut you. Keep
hands and feet away from the hopper and the discharge chute.
Before using the wood chipper + shredder, familiarize yourself
with the controls, especially how to stop the unit in an
emergency. The only individuals who should use the wood
chipper + shredder are those who thoroughly understand
these instructions and know how to properly operate the unit.
Children should never be allowed access to the wood chipper
+ shredder.
Retain this manual for future reference and reread it at the start
of each chipping season.
General Safety
1. Avoid dangerous environments – Do not use the wood
chipper + shredder in rain or in damp or wet locations. Do
not operate the unit in gaseous or explosive atmospheres
or use the unit near ammable or combustible liquids.
Motors in these tools normally spark, and the sparks
might ignite fumes.
2. Dress properly – Do not wear loose clothing or jewelry as
such articles can become caught in moving parts. Wear
a protective covering to contain long hair. Wearing rubber
gloves and substantial non-slip footwear is recommended
when working outdoors.
3. Use safety glasses – Also use dust mask, safety
footwear, snug-tting clothing, protective gloves, hearing,
and head protection.
4. Extension cords – To prevent electric shock, use only
with an extension cord suitable for outdoor use.
5. Disconnect the tool – Disconnect the wood chipper +
shredder from the power supply when it is not in use,
before servicing it, when changing accessories, and when
performing any other maintenance task.
6. Do not abuse the cord – Never carry the wood chipper
+ shredder by the cord or yank the cord to disconnect it
from the receptacle. Keep the cord away from heat, oil,
and sharp edges.
7. Stay alert – Watch what you are doing. Use common
sense. Do not operate the wood chipper + shredder when
you are tired or under the inuence of drugs, alcohol, or
other medication.
8. Store idle tool indoors – When not in use, the wood
chipper + shredder should be stored indoors in a dry and
high or locked-up place out of the reach of children.
9. Maintain the wood chipper + shredder with care –
Keep the cutting edges sharp and clean for optimal
performance and to reduce the risk of injury. Inspect the
extension cord periodically and immediately replace it
if damaged. Keep the handles dry, clean, and free from
oil and grease. Follow the additional recommendations
described in the Care + Maintenance section of this
manual.
10. Check for damaged parts – Before further use of the
appliance, a part that is damaged should be carefully
checked to determine that it will operate properly and
perform its intended function. Check for alignment of
moving parts, binding of moving parts, breakage of parts,
mounting, and any other condition that may aect its
operation. A part that is damaged should be properly
repaired or replaced. Contact the Snow Joe® + Sun Joe®
customer service center at 1-866-SNOWJOE
(1-866-766-9563) for assistance.
11. Lighting – Only operate your wood chipper + shredder in
daylight or good articial light.
2
12. Do not overreach – Keep proper footing and balance at
all times.
13. Never leave a running tool unattended – Turn the
wood chipper + shredder o and wait until it comes to a
complete stop before leaving the work area.
14. Avoid accidental starting – Do not carry the wood
chipper + shredder with your nger on the switch. Make
sure the switch is o before plugging in or unplugging the
unit.
15. Use the right tool – Do not use this machine for any job
except that for which it was intended.
16. Keep children, bystanders, and pets away – All
spectators, including pets, should be kept a safe distance
away from the work area.
Personal Safety
1. Before starting the wood chipper + shredder, make sure
that the hopper inlet is empty.
2. Keep your face and body away from the opening.
3. Do not allow hands or any other part of the body or
clothing near the hopper or discharge chute.
4. Never put your hands into the hopper while the wood
chipper + shredder is running. Always use the paddle
supplied with your wood chipper + shredder to push items
into the hopper.
5. Do not try to force objects larger than the recommended
diameter of 1-1/2" into the hopper.
6. Always stand clear of the discharge zone when operating
the wood chipper + shredder. Never reach under the unit
until it has come to a complete stop.
7. When feeding material into the wood chipper + shredder,
be careful to remove pieces of metal, rocks, bottles, cans
or other foreign objects that may damage the blades.
8. If the cutting mechanism strikes a foreign object or if the
wood chipper + shredder should start making any unusual
noise or vibration, turn it o and allow it to come to a
complete stop. Disconnect from power supply and take
the following steps:
– Inspect for damage;
– Check for and tighten any loose parts.
mWARNING! Never reach into the hopper until the
wood chipper + shredder has come to a complete stop and
is unplugged. The blades will continue to rotate for a few
seconds after the unit is turned o.
9. Do not allow processed material to build up in the
discharge zone; this may prevent proper discharge and
can result in kickback of material through the hopper.
mWARNING! Never put your hands near the
discharge chute. Failure to heed the warning could result in
serious injury.
10. If the wood chipper + shredder becomes clogged, turn it
OFF and disconnect from power supply before clearing
debris. Keep the power source clear of debris and other
accumulations to prevent damage to the power source.
Remember that the starting mechanism on engine
powered tools will cause the cutting mechanism to move.
11. Keep all guards and deectors in place and in good
working condition.
12. Do not operate the wood chipper + shredder on a paved
or gravel surface where ejected material could cause
injury.
13. Turn o the wood chipper + shredder and disconnect it
from the power supply whenever you leave the work area.
14. Do not tilt the wood chipper + shredder while it is running.
15. Never reach into the hopper until the wood chipper +
shredder has come to a complete stop and has been
disconnected from the power supply.
3
Electric Safety
1. Ground fault circuit interrupter (GFCI) protection should
be provided on the circuit(s) or outlet(s) to be used for
this electric wood chipper + shredder. Receptacles are
available having built-in GFCI protection and may be used
for this measure of safety.
2. To prevent electric shock, use only with an extension cord
suitable for outdoor use, such as SW-A, SOW-A, STW-A,
STOW-A, SJW-A, SJOW-A, SJTW-A, or SJTOW-A.
Before use, check that the extension cord is in good
condition. When using an extension cord, make sure to
use one heavy enough to carry the current to the product.
An undersized cord will cause a drop in line voltage
resulting in loss of power and overheating.
3. To reduce the risk of electric shock, this appliance has
a polarized plug (i.e. one blade is wider than the other).
Use this appliance only with a polarized UL-, CSA-, or
ETL-listed extension cord recommended for outdoor,
all-weather use, such as the Snow Joe® + Sun Joe®
SJTW-A 14-gauge 50-foot extension cord with lighted
end (Model PJEXT50-B). Visit snowjoe.com to purchase
this extension cord online or, to order by phone, call
1-866-SNOWJOE (1-866-766-9563).
The appliance plug will t into a polarized extension
cord only one way. If the appliance plug does not t
fully into the extension cord, reverse the plug. If the plug
still does not t, obtain a correct polarized extension
cord. A polarized extension cord will require the use of a
polarized wall outlet. The extension cord plug will t into
the polarized wall outlet only one way. If the plug does
not t fully into the wall outlet, reverse the plug. If the plug
still does not t, contact a qualied electrician to install
the proper wall outlet. Do not modify the appliance plug,
extension cord receptacle, or extension cord plug in any
way.
4. To prevent the appliance cord from disconnecting from the
extension cord during operation, make a knot with the two
cords as shown in Table 1.
5. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodied plugs and
matching outlets will reduce risk of electric shock.
6. Avoid body contact with earthed or grounded surfaces,
such as pipes, radiators, ranges and refrigerators. There is
an increased risk of electric shock if your body is earthed
or grounded.
7. If the supply cord is damaged, it must be replaced by an
electrician or a power tool repairer.
8. When operating a power tool outdoors, use an extension
cord suitable for outdoor use. Use of a cord suitable for
outdoor use reduces the risk of electric shock.
9. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
10. Have your tool repaired by an electrician or a qualied
service center. This power tool complies with relevant
safety requirements. To avoid danger, electrical appliances
must only be repaired by qualied personnel using original
spare parts; otherwise this may result in considerable
damage to the user.
m WARNING! m
Electric shock may cause SEVERE INJURY or
DEATH. Heed these warnings:
• Do not allow any part of the wood chipper + shredder
to make contact with water while it is in operation. If
the appliance becomes wet while turned o, wipe dry
before starting.
• Use only a UL-, CSA- or ETL-rated extension cord for
outdoor, all-weather use.
• Do not use an extension cord over 100 ft (30 m).
• Do not touch the appliance or its plug with wet hands
or while standing in water. Wearing rubber boots
oers some protection.
EXTENSION CORD CHART
Cord Length:
Min. Wire Gauge (A.W.G.):
Up to 50 ft
(15 m)
14
+50 ft - 100 ft
(+15 m - 30 m)
12
(B) Connect plug and receptacle
Cord set Appliance cord
(A) Tie cord as shown
Table 1. Method of Securing Extension Cord
Specyfikacje produktu
| Marka: | Sun Joe |
| Kategoria: | łuparka do drewna |
| Model: | CJ602E |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Sun Joe CJ602E, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje łuparka do drewna Sun Joe
23 Września 2024
23 Września 2024
17 Sierpnia 2024
5 Lipca 2024
Instrukcje łuparka do drewna
- łuparka do drewna Scheppach
- łuparka do drewna Remington
- łuparka do drewna RYOBI
- łuparka do drewna Baumr-AG
- łuparka do drewna Meec Tools
- łuparka do drewna AL-KO
- łuparka do drewna Güde
- łuparka do drewna ATIKA
- łuparka do drewna Zipper
- łuparka do drewna Faworyt
- łuparka do drewna Fieldmann
- łuparka do drewna Cotech
- łuparka do drewna Bell
- łuparka do drewna Anova
- łuparka do drewna Michigan
- łuparka do drewna Wallenstein
- łuparka do drewna Powerhouse
Najnowsze instrukcje dla łuparka do drewna
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
7 Października 2024
6 Października 2024
1 Października 2024
30 Września 2024
29 Września 2024
29 Września 2024