Instrukcja obsługi StarTech.com SU2DUPERA11

StarTech.com Niesklasyfikowane SU2DUPERA11

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla StarTech.com SU2DUPERA11 (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

Quick-start guide

Manual Revision: 10/24/2016

For the latest information, technical specications, and support for

this product, please visit www.StarTech.com/SU2DUPERA11.

Package contents

• 1 x SATA/USB duplicator and eraser

• 1 x universal power adapter (NA/JP, UK, EU, AU)

• 2 x drive-connector cables

• 2 x drive pads

• 1 x quick-start guide

System requirements are subject to change. For the latest

requirements, please visit www.StarTech.com/SU2DUPERA11.

SU2DUPERA11

Standalone Drive Duplicator and Eraser for USB Flash Drives and 2.5”/3.5” SATA SSDs /HDDs

*actual product may vary from photos

Read and understand the entire manual before Important:

you use this product, and follow the instructions as they are

outlined in the manual.

Failure to do so might result in property damage or device

failure.

Product diagram

USB source

port

SATA source port

LCD display

Menu navigation

buttons

OK button

Exit button

USB source LEDs

SATA source LEDs

USB target port

SATA target

port

USB target LEDs

SATA

target LEDs

Power switch

Power jack

Erase and copy modes

The SU2DUPERA11 supports ve erase modes and four copy modes.

Mode Denition

Erase modes

Quick erase The partition table is quickly erased.

Full erase The entire drive is erased.

DoD 5220.22-M erase A three-pass overwrite based on

DoD 5220.22-M specications

is completed.

DoD 5220.22-M erase

and compare

A three-pass overwrite based on

DoD 5220.22-M specications

is completed and compared.

Secure erase The ATA Secure Erase feature of the

drive is executed.

Note: The Secure Erase feature isn’t

supported on USB drives.

Copy modes

Copy system and les Only the data area of the source drive is

copied and the empty space

isn’t copied.

Copy all partitions All of the partitions and data, including

blank partitions, are copied. Blank space

and nonpartition space isn’t copied.

Copy the whole drive The entire drive is copied, including

empty space.

Copy a percentage A specied percentage range of the

drive is copied.

About copying drives

You can use the SU2DUPERA11 to copy SATA drives in any of the

following congurations:

• SATA drive to SATA drive

• SATA drive to USB drive

• USB drive to USB drive

• USB drive to SATA drive

Copy a SATA or USB drive

Note: You should avoid plugging SATA drives directly into the

SU2DUPERA11, as it puts undue strain on the device connectors. Use

the drive-connector cables instead.

Warning! Make sure that the storage capacity of the target drive

is larger than or equal to the storage capacity of the source drive.

Otherwise, you will get an error when you try to copy your drive.

Warning! After you begin copying a drive, don’t disconnect either

drive or interrupt the process before it has nished. Doing so might

result in damage to the drive or lost data.

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment

o and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation. Changes or

modications not expressly approved by StarTech.com could void the user’s authority to operate

the equipment.

Technical Support

StarTech.com’s lifetime technical support is an integral part of our commitment to provide

industry-leading solutions. If you ever need help with your product, visit www.startech.com/

support and access our comprehensive selection of online tools, documentation, and downloads.

For the latest drivers/software, please visit www.startech.com/downloads

Industry Canada Statement

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.

CAN ICES-3 (B)/NMB-3(B)

Use of Trademarks, Registered Trademarks, and other Protected Names

and Symbols

This manual may make reference to trademarks, registered trademarks, and other protected

names and/or symbols of third-party companies not related in any way to

StarTech.com. Where they occur these references are for illustrative purposes only and do not

represent an endorsement of a product or service by StarTech.com, or an endorsement of the

product(s) to which this manual applies by the third-party company in question. Regardless

of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby

acknowledges that all trademarks, registered trademarks, service marks, and other protected

names and/or symbols contained in this manual and related documents are the property of their

respective holders.

Warranty Information

This product is backed by a two-year warranty. StarTech.com warrants its products against defects

in materials and workmanship for the periods noted, following the initial date of purchase. During

this period, the products may be returned for repair, or replacement with equivalent products at

our discretion. The warranty covers parts and labor costs only. StarTech.com does not warrant its

products from defects or damages arising from misuse, abuse, alteration, or normal wear and tear.

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers,

directors, employees or agents) for any damages (whether direct or indirect, special, punitive,

incidental, consequential, or otherwise), loss of prots, loss of business, or any pecuniary loss,

arising out of or related to the use of the product exceed the actual price paid for the product.

Some states do not allow the exclusion or limitation of incidental or consequential damages. If

such laws apply, the limitations or exclusions contained in this statement may not apply to you.

Erase a single SATA or USB drive

Note: You should avoid plugging SATA drives directly into the

SU2DUPERA11, as it puts undue strain on the device connectors. Use

the drive-connector cables instead.

Warning! Before you erase a drive, make sure that you back up any

important data from the drive to a safe location.

Warning! After you press the , don’t disconnect the drive OK button

until the process is complete. Removing the drive before it is done

being erased might result in damage to the drive.

1. Connect the universal power adapter to the Power jack on the

back of the SU2DUPERA11, and to a power source.

2. Use the Power switch on the back of the device to turn it on.

3. Connect the drive that you want to erase to either the USB target

port SATA target portor the .

4. Place the drive on the included drive pad. Avoid placing drives

directly on a metal surface.

5. Use the Menu navigation buttons on the device to navigate to

the menu, and press the .Erase OK button

6. Select an erase mode, and press the .OK button

About the LED indicators

The LED indicators associated with both the source and target SATA

drives exhibit the same behavior. Consult the table below for more

information.

LED behavior Signicance

Yellow LED is illuminated Indicates that the drive is

connected correctly.

Green LED is blinking Indicates that activity is occurring.

Red LED is illuminated

or blinking

Indicates that an error is occurring.

Check the LCD display for

more information.

1. Connect the universal power adapter to the Power jack on the

back of the SU2DUPERA11 and to a power source.

2. Use the Power switch on the back of the device to turn it on.

3. Connect a drive to either the USB source port SATA or the

source port.

4. Connect the other drive to either the or the USB target port

SATA target port.

5. Place the drives on the included drive pads. Avoid placing drives

directly on a metal surface.

6. Use the on the device to navigate to Menu navigation buttons

the menu, and press the .Setup OK button

7. Navigate to the Copy Area OK button menu, and press the .

8. Select a copy mode, and press the .OK button

9. Use the buttons on the device to navigate Menu navigation

back to the main menu.

10. Select , and press the .Copy OK button

Erase multiple drives simultaneously

Note: You should avoid plugging SATA drives directly into the

SU2DUPERA11, as it puts undue strain on the device connectors. Use

the drive-connector cables instead.

Warning! Before you erase a drive, make sure that you back up any

important data from the drive to a safe location.

Warning! After you press the , don’t disconnect the drive OK button

until the process is complete. Removing the drive before it is done

being erased might result in damage to the drive.

1. Connect the universal power adapter to the Power jack on the

back of the SU2DUPERA11, and to a power source.

2. Use the Power switch on the back of the device to turn it on.

3. Connect one of the drives that you want to erase to either the

USB target port SATA target port or the .

4. Connect the other drive that you want to erase to either the USB

source port SATA source port or the .

5. Place the drive on the included drive pad. Avoid placing drives

directly on a metal surface.

6. Use the Menu navigation buttons on the device to navigate to

the menu, and press the .Setup OK button

7. Navigate to and press the .Erase Master OK button

8. Select and press the .Enable OK button

9. Select an erase mode, and press the .OK button

Specyfikacje produktu

Marka:	StarTech.com
Kategoria:	Niesklasyfikowane
Model:	SU2DUPERA11

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z StarTech.com SU2DUPERA11, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Niesklasyfikowane StarTech.com

StarTech.com MCM110SC2P Instrukcja

9 Października 2024

StarTech.com PLATE9M Instrukcja

9 Października 2024

StarTech.com RACKCONV1901 Instrukcja

9 Października 2024

StarTech.com PLATE9MB Instrukcja

9 Października 2024

StarTech.com ET91000LC2 Instrukcja

9 Października 2024

StarTech.com ET10GSFP Instrukcja

9 Października 2024

StarTech.com MCM1110SFP Instrukcja

9 Października 2024

StarTech.com ET91000SFP2 Instrukcja

9 Października 2024

StarTech.com ET91000LC Instrukcja

9 Października 2024

StarTech.com ET91000LCOAM Instrukcja

9 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024

Stihl HT 70 Instrukcja

15 Października 2024

Ernesto H14270 Instrukcja

15 Października 2024

Uniden BT MIC KIT Instrukcja

15 Października 2024

Vaude Omnis Bike 26 Instrukcja

15 Października 2024

ART ProChannel II Instrukcja

15 Października 2024

Aukey DR02J Instrukcja

15 Października 2024

Master Lock 653EURD Instrukcja

15 Października 2024

Roland FR-18 Diatonic Instrukcja

15 Października 2024