Instrukcja obsługi StarTech.com ST121HD20L

StarTech.com przedłużacz AV ST121HD20L

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla StarTech.com ST121HD20L (2 stron) w kategorii przedłużacz AV. Ta instrukcja była pomocna dla 13 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

Quick-Start Guide

To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.

Manual Revision: August 12, 2019

Product Diagram (ST121HD20L)

Transmitter and Receiver Front View

Component Function

Transmitter and Receiver

1Power LED Indicator • Solid green when the Universal Power Adapter

is connected

Transmitter

2Link LED Indicator • Solid green when the is HDMI Source Device

connected

Receiver

2Link LED Indicator

• Solid green when the is connected CAT6 Cable

and the is HDMI Source Device Video Signal

active

Transmitter and Receiver Rear View

HDMI over CAT6 Extender | 4K 60Hz

Port Function

Transmitter and Receiver

3DC IN Ports

• Power the and Transmitter Receiver

• Secure the into the Universal Power Adapters

DC IN Ports Barrel Connectors by inserting the

on the and turning Universal Power Adapters

the clockwiseScrew Locks

4HDMI IN and OUT

Ports

• Connect an andHDMI Source HDMI Display

Device

5IR TX and RX Ports

• Connect the (Infrared) and IR Blasters

Receivers HDMI Source to control the and

HDMI Display Device Transmitter from the or

Receiver

• Bi-directional to support dierent IR

congurations

6RS-232 Extension

Ports

• Connect any to extend the signal Serial Device

over CAT6 Cable

7RJ45 Ports

• Connect the to extend the signal CAT6 Cable

from the to the Source Device HDMI Display

Device

Requirements

For the latest requirements and to view the full User Manual, please visit

www.startech.com/ST121HD20L.

• HDMI Source Device x 1

• HDMI Display Device x 1

• CAT6 Cable x 1

• (Optional) Surface for Mounting x 1

Installation

Installing the HDMI Transmitter and Receiver

1. Position the near the . Transmitter HDMI Source Device

2. Connect an to the and to the on HDMI Cable HDMI Source Device HDMI IN Port

the back of the .HDMI Transmitter

45 6 7

1 2

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation. Changes or modications not expressly approved by StarTech.com could void

the user’s authority to operate the equipment.

Industry Canada Statement

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.

CAN ICES-3 (B)/NMB-3(B)

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may

cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation

est autorisée aux deux conditions suivantes:

(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,

même si le brouillage est susceptible d’en compromettre le fonctionnement.

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-

party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only

and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which

this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered

trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the

property of their respective holders.

Warranty Information

This product is backed by a two-year warranty.

For further information on product warranty terms and conditions, please refer to .www.startech.com/warranty

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)

for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of

business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.

Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations

or exclusions contained in this statement may not apply to you.

Safety Measures

• If product has an exposed circuit board, do not touch the product under power.

Mesures de sécurité

• Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.

安全対策

• 製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください。

Misure di sicurezza

• Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.

Säkerhetsåtgärder

• Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.

FR: fr.startech.com

DE: de.startech.com

ES: es.startech.com

NL: nl.startech.com

IT: it.startech.com

JP: jp.startech.com

StarTech.com Ltd.

45 Artisans Cres

London, Ontario

N5V 5E9

Canada

StarTech.com Ltd.

Unit B, Pinnacle 15

Gowerton Rd,

Brackmills

Northampton

NN4 7BW

United Kingdom

StarTech.com LLP

2500 Creekside

Parkwy

Lockbourne, Ohio

43137

U.S.A.

5. Use the for the to control the Remote Control HDMI Source Device HDMI Display

Device Transmitter’s from the location.

Control the HDMI Source Device from the Receiver

1. Connect the (L shaped) to the on the .Infrared Blaster IR - RX Port Transmitter

2. Peel the o of the that is located on the . Stick Film Adhesive Pad Infrared Blaster

the so that it is pointing directly at the on the Infrared Blaster IR Sensor HDMI

Source Device.

Note: Consult the manual to determine the location of the HDMI Source Device’s IR

Sensor.

3. Connect the (oval shaped) to the on the .Infrared Receiver IR - TX Port Receiver

4. Peel the o of the that is located on the Film Adhesive Pad Infrared Receiver.

Stick the in a location where there is a clear path to the Infrared Receiver Remote

Control.

Notes: Infrared signals require a direct line of sight to function.

Consult the manual for the to determine the location of the HDMI Display Device IR

Sensor.

5. Use the for the to control the Remote Control HDMI Source Device HDMI Source

Device Receiver’s from the location.

3. Connect a (included) to the on the back of the CAT6 Cable RJ45 Port HDMI

Transmitter RJ45 Port HDMI Receiver and to the on the back of the .

Note: The cabling should not go through any networking equipment (e.g. router,

switch, etc.).

4. Position the near the .HDMI Receiver HDMI Display Device

5. Connect an to the on the back of the HDMI Cable HDMI OUT Port HDMI Receiver

and to the .HDMI Display Device

6. Connect the to the on the and Universal Power Adapters DC IN Ports Transmitter

Receiver AC Electrical Outlets and to two .

Installing the IR Blaster and IR Receiver

Control the HDMI Display Device from the Transmitter

1. Connect the (oval shaped) to the on the .Infrared Receiver IR - TX Port Transmitter

2. Peel the o of the that is located on the . Film Adhesive Pad Infrared Receiver

Stick the in a location where there is a clear path to the Infrared Receiver Remote

Control.

Note: Ensure there is an unobstructed path to the . Infrared signals Infrared Receiver

require a direct line of sight to function.

3. Connect the (L shaped) to the on the .Infrared Blaster IR - RX Port Receiver

4. Peel the o of the that is located on the Stick Film Adhesive Pad Infrared Blaster.

the on the so that it is pointing directly at the Infrared Blaster HDMI Display Device

IR Sensor Display on the .

Note: Consult the manual to determine the location of the HDMI Display Device’s IR

Sensor.

Specyfikacje produktu

Marka:	StarTech.com
Kategoria:	przedłużacz AV
Model:	ST121HD20L

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z StarTech.com ST121HD20L, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje przedłużacz AV StarTech.com

StarTech.com RS232EXTC1EU Instrukcja

1 Stycznia 2025

StarTech.com NETRS2321EGB Instrukcja

1 Stycznia 2025

StarTech.com NETRS232_2GB Instrukcja

1 Stycznia 2025

StarTech.com NETRS232_1GB Instrukcja

1 Stycznia 2025

StarTech.com NETRS232_1EU Instrukcja

1 Stycznia 2025

StarTech.com CB420USB Instrukcja

1 Stycznia 2025

StarTech.com PEXUSB400 Instrukcja

1 Stycznia 2025

StarTech.com PEX400USB2 Instrukcja

1 Stycznia 2025

StarTech.com PCIUSB7 Instrukcja

1 Stycznia 2025

StarTech.com PCI420USB Instrukcja

31 Grudnia 2025

Instrukcje przedłużacz AV

Najnowsze instrukcje dla przedłużacz AV

DataVideo HBT-11 Instrukcja

15 Stycznia 2025

Kopul XLR4F-RJ45 Instrukcja

14 Stycznia 2025

Kopul RM-4X4XMFRJ45 Instrukcja

14 Stycznia 2025

Planet VF-106G-KIT Instrukcja

13 Stycznia 2025

Tripp Lite B127-008-D Instrukcja

13 Stycznia 2025

Kopul RM-12XFRJ45 Instrukcja

13 Stycznia 2025

Kopul XLR4M-RJ45 Instrukcja

13 Stycznia 2025

Kopul RM-12XMRJ45 Instrukcja

13 Stycznia 2025

Atlona AT-AVA-EX70-2PS-KIT Instrukcja

10 Stycznia 2025

Atlona AT-HDR-EX-100CEA-RX Instrukcja

10 Stycznia 2025