Instrukcja obsługi StarTech.com IDE2CFINT

StarTech.com Niesklasyfikowane IDE2CFINT

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla StarTech.com IDE2CFINT (1 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/1
Introduction
Thank you for purchasing a StarTech.com Compact
Flash to IDE Embedded Card Reader. This product
allows you to connect a compact flash memory card
to a 3.5” IDE Host Interface. After installation, the
host PC will be able to read an inserted Compact
Flash as a standard IDE hard disk.
Features
• Voltage selection for +3.3V or +5.0V compact flash
• On-board LED indicators for power-on and
compact flash access
• Fully compatible with Flash Type I, Type II, and
Micro-drive
• Driverless Hardware, will work with any system that
supports IDE interface
Before You Begin
System Requirements
• An available 40-way (2.54mm) standard IDE
connector
• A +5V floppy disk drive power connector
Basic Setup
Connecting the card reader to the computer
1. Shut down all power connected to the computer as
well as all devices connected to the computer
peripherally. As an added step to ensure safe
installation, unplug the power supply to the
computer.
2. Remove the computer cover. For more detailed
instruction on how to perform this step, please refer
to the documentation that was included with your
computer at the time of purchase.
3. Insert the IDE2CFINT into an available 40-way IDE
connector.
4. Connect the +5V floppy disk drive power
connector (4) to the floppy drive power source.
5. Replace the top of the computer case, as well as
the power cord.
(If your flash card is ready to be installed, skip to
Using the Card Reader - step 3)
Using the Card Reader
Note: This adaptor does not support hot insertion of
CF cards.
1. Make sure the computer is powered down.
2. Open the computer case.
3. Gently insert the desired Compact Flash Card into
the provided socket, using the guide rails to ensure
the pins on the reader are properly aligned with the
card. Note: If the Flash Card is not properly
aligned, you risk causing permanent damage to the
card as well as to the reader.
4. Once the flash card is secured, replace the cover
on the computer casing.
Upon powering the computer back on, the flash card
should be detected as an IDE hard drive.
J
J
J
J
Ju
u
u
u
um
m
m
m
mp
p
p
p
pe
e
e
e
er
r
r
r
r
s
s
s
s
se
e
e
e
et
t
t
t
tt
t
t
t
ti
i
i
i
in
n
n
n
ng
g
g
g
gs
s
s
s
s
By default, the IDE2CFINT is set to act as a Master
drive. As such, ensure that this is reflected accurately
from within your system BIOS. To change the
IDE2CFINT to act as a Slave drive, adjust the
jumper located on JP3 to pins 2 and 3, making the
necessary adjustments to your BIOS settings.
L
L
L
L
LE
E
E
E
ED
D
D
D
D f
f
f
f
fu
u
u
u
un
n
n
n
nc
c
c
c
ct
t
t
t
ti
i
i
i
io
o
o
o
on
n
n
n
ns
s
s
s
s
LED 1 - Card detect indicator
LED 2 - Memory Access activity indicator
LED 3 - Power-on indicator
Warranty and Support
Compact Flash to IDE Embedded Card
Reader
IDE2CFINT
Revised: 22 December 2005 (A)
Support, Warranty Information, and Regulatory Compliance Statement
If you ever need help with your product, visit and access our com-www.startech.com/support
prehensive selection of online tools, documentation, and downloads. This product is backed by a
one-year warranty. In addition, StarTech.com warrants its products against defects in mater ials
and workmanship for the periods noted, following the initial date of purchase. During this period,
the products may be returned for repair, or replacement with equivalent products at our discre-
tion. The warranty covers parts and labor costs only. StarTech.com does not warrant its products
from defects or damages arising from misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability: In no event shall the liability of StarTech.com Ltd. and StarTech.com USA
LLP (or their officers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business, or any
pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for
the product. Some states do not allow the exclusion or limitation of incidental or consequential
damages. If such laws apply, the limitations or exclusions contained in this statement may not
apply to you.
FCC Compliance Statement: This equipment has been tested and found to comply with the lim-
its for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be deter-
mined by turning the equipment off and on, the user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is con-
nected.
• Consult the dealer or an experienced radio/TV technician for help.
Power
JP1JP2JP3
1
2
3
LED 1
LED 3
LED 2
Flash Card Socket

Specyfikacje produktu

Marka: StarTech.com
Kategoria: Niesklasyfikowane
Model: IDE2CFINT

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z StarTech.com IDE2CFINT, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane StarTech.com

StarTech.com

StarTech.com MCM110SC2P Instrukcja

9 Października 2024
StarTech.com

StarTech.com PLATE9M Instrukcja

9 Października 2024
StarTech.com

StarTech.com RACKCONV1901 Instrukcja

9 Października 2024
StarTech.com

StarTech.com PLATE9MB Instrukcja

9 Października 2024
StarTech.com

StarTech.com ET91000LC2 Instrukcja

9 Października 2024
StarTech.com

StarTech.com ET10GSFP Instrukcja

9 Października 2024
StarTech.com

StarTech.com MCM1110SFP Instrukcja

9 Października 2024
StarTech.com

StarTech.com ET91000SFP2 Instrukcja

9 Października 2024
StarTech.com

StarTech.com ET91000LC Instrukcja

9 Października 2024
StarTech.com

StarTech.com ET91000LCOAM Instrukcja

9 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024