Instrukcja obsługi Sony Bravia K-55XR84

Sony Telewizja Bravia K-55XR84

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Sony Bravia K-55XR84 (4 stron) w kategorii Telewizja. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/4
| 1
RF40 Rudder Feedback unit
Installation guide
The RF40 is a resistive rudder feedback unit, suitable for autopilot systems with a
NAC-1 or NAC-2 autopilot computer.
¼Note: The RF40 can not be used with the NAC-3 autopilot computer.
The RF40 might also be used with autopilot computers that have analog rudder
feedback input.
¼Note: Do not remove the transmitter lever from the feedback unit.
¼Note: The unit is factory adjusted and requires no further adjustment at
installation than described below.
Mounting location
The RF40 unit ( ) mounts close to the rudder, and is mechanically linked to the A
rudder tiller arm ( ) or rudder quadrant.B
Select a mounting location for the RF40 unit according to the illustration
X1 = X2: min 150 mm (5.9”), max 345 mm (13.6)
Y1 = Y2: min 44 mm (1.7”), max 130 mm (5.1)
X2
X1
Y1 Y2
X1 = X2
Y1 = Y2
A
B
2 |
Installation
The RF40 lever ( ) has two slots for the transmitter link ( ). The slots enable C D
maximum exibility to provide the 1:1 mechanical linkage relationship.
D
E
E
C
B
Y1 Y2
1. Turn the helm to set the rudder tiller arm ( ) to approximate center positionB
2. Mount the RF40 unit to a suitable platform
If required:
-add blocking material under the RF40 to adjust the height of the
transmitter lever to be level with the rudder tiller arm
-cut the length of the transmitter rod (D) to move the feedback unit closer
to the rudder post
3. Rotate the RF40 lever to center position
Ethe marks ( ) on unit and on the lever should be aligned
4. Rotate the RF40 unit so that the rudder lever is parallel with the rudder tiller arm
5. Set the transmitter link to the inner limit of the outer slot if possible
6. Drill and tap the rudder tiller arm so that the Y2 dimension is equal to the Y1
dimension
7. Attach the ball joint to the tiller arm, and connect the transmitter rod to the ball
joint at the rudder tiller arm
8. Tighten the mounting screws for both the RF40 and the transmitter rod ball
joint.
9. Observe the feedback unit while someone turns the helm through the complete
rudder travel hard-over to hard-over, and verify that the mechanical linkage
moves freely.
| 3
Wiring
The RF40 is equipped with a 15 m (49 feet) cable with connector (A). The unit
connects to the NAC-1/NAC-2 autopilot computer’s three pins rudder feedback
socket ( ).
B
A B
3
12
3
1 2
Function Color
1+5 V DC Red
2Signal Yellow
3-0 V DC Black
Dimensional drawings
RF40
177 mm (6.97”)
55 mm
(2.16”)
99 mm (3.90”)
65 mm
(2.56”)
Transmitter link
345 mm (13.6”)


Specyfikacje produktu

Marka: Sony
Kategoria: Telewizja
Model: Bravia K-55XR84

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Sony Bravia K-55XR84, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Telewizja Sony

Sony

Sony KV-1944R Instrukcja

13 Stycznia 2025
Sony

Sony KDL-37FA500 Instrukcja

13 Stycznia 2025
Sony

Sony KD-65X77L Instrukcja

22 Grudnia 2024
Sony

Sony XBR85X950H Instrukcja

14 Października 2024
Sony

Sony Bravia KDL-46XBR8 Instrukcja

13 Października 2024
Sony

Sony LF-PK1 Instrukcja

10 Października 2024
Sony

Sony Bravia KDL-52S4100 Instrukcja

10 Października 2024

Instrukcje Telewizja

Najnowsze instrukcje dla Telewizja