Instrukcja obsƂugi Simpson SuperPro SW5050HUGL-S

Simpson Myjka wysokociƛnieniowa SuperPro SW5050HUGL-S

Przeczytaj poniĆŒej 📖 instrukcję obsƂugi w języku polskim dla Simpson SuperPro SW5050HUGL-S (124 stron) w kategorii Myjka wysokociƛnieniowa. Ta instrukcja byƂa pomocna dla 14 osĂłb i zostaƂa oceniona przez 2 uĆŒytkownikĂłw na ƛrednio 4.5 gwiazdek

Pobierz PDF
Strona 1/124
Part Number 7110656 / ENGLISH REV E - 5/2023
SAVE THIS MANUAL FOR FUTURE REFERENCE
USE AND CARE MANUAL
PRESSURE WASHER
READ THIS MANUAL CAREFULLY BEFORE OPERATION
Failure to follow the instructions and safety precautions in this manual can result
in property damage, serious injury and/or death.
NOTE: Photographs and line drawings used in this manual are for reference only and may not
represent your specic model.
If your pressure washer is not working or if there are parts missing or broken, please DO NOT
RETURN IT TO THE PLACE OF PURCHASE. Contact our Customer Service Department by calling
1-877-362-4271 or emailing cservice@fna-group.com
LOOK BEFORE YOU PUMP!
Manuel en Français
Manual de idioma Español
Page II
NOTES
THIS PAGE WAS INTENTIONALLY LEFT BLANK
Page 1
SAVE THIS MANUAL FOR FUTURE USE
Write down the model number, serial number, and purchase date of this product in the spaces
provided below then keep this manual with the purchase receipt(s) for future reference.
Keep this manual for future reference. This manual should be considered a permanent part
of the product and stay with it. This manual should be available to anyone operating the
product(s) it covers. This manual should remain with the product(s) it covers if sold to a new
owner. If the manual becomes damaged, lost, or otherwise unusable, you may download
a new copy from the product pages at www.simpsoncleaning.com or contact customer
support by calling 1-877-362-4271.
Model Number:
Serial Number:
Purchase Date:
Page 2
TABLE OF CONTENTS
Adding the Pump Breather Cap 6
Assemble the Spray Gun 6
ASSEMBLY 6
DISCLAIMERS 5
PERSONAL PROTECTIVE EQUIPMENT
5
Hazard Alert Symbols 4
Additional Instructions 4
Read this Manual Before Operating 4
4SAFETY INSTRUCTIONS
Battery Connections
Place Nozzles in Holders
7
7
COMPONENT LOCATION 8
CONNECTING HOSES 14
PURGING AIR FROM THE PUMP 15
NOZZLES 16
Nozzle Installation 16
Nozzle Selection 16
USING CHEMICALS 17
OPERATING CHECKLIST 18
High Altitude Operation
Location 18
Checking the Engine Oil
Operating Conditions
Checking Fuel
19
19
20
22
STARTING THE ENGINE 24
UNPACKING 6
Two-cylinder Engine with Direct-drive Pump 10
Single-cylinder Engine with Direct-drive Pump 8
Single-cylinder Engine with Belt-driven Pump 12
Electric Start
Manual Start 24
25
Hand thread the lance clockwise into the gun. Be careful not to cross-
thread the spray gun and lance. Using an adjustable wrench, tighten the
lance by placing the wrench on the ats of the nozzle quick-connector.
WARNING!
The threads on the lance and spray gun coupler can be easily cross threaded
resulting in an improper assembly. An improper assembly of the spray gun and lance can
result in personal injury. Do not use if the threads on the gun coupler and or lance are cross
threaded.
Page 6
UNPACKING
ASSEMBLY
Follow the steps outlined in this section to unpack and assemble your pressure washer.
If you have any questions regarding the unpacking or assembly of your pressure washer,
please have your model number and serial number ready, then contact customer support at
1-877-362-4271 or email cservice@fna-group.com.
1. Place the shipping carton on a solid, at surface.
2. Carefully cut the top of the carton open.
3. Carefully cut each corner of the carton from top to bottom.
4. Lay each side of the carton at on the ground.
5. Remove everything from the carton.
Assemble the spray gun
Adding the pump breather cap (if applicable)
A shipping cap is in the pump that must be replaced with a breather cap. The cap is easy
to replace with the following steps:
Shipping cap
Breather cap
1. Using a bladed screwdriver, remove the shipping cap.
2. Hand thread the breather cap into the pump.
3. Snug the cap with your ngers.
WARNING:
WARNING:
WARNING:
WARNING:
WARNING:
RISK OF ACID BURNS
DANGER:
DANGER:
DANGER:
DANGER:
DANGER:
Page 7
Attempting to start the engine incorrectly or using the pressure washer incorrectly can
result in engine and/or pressure washer damage, and may cause serious injury or death.
To avoid these hazards, be sure to read, understand, and follow the steps outlined in the
OPERATING CHECKLIST section of the owner’s manual before starting the engine, and
follow all the guidelines for proper use of the pressure washer.
OPERATING CHECKLIST
Place nozzles in holders (if equipped)
Place the nozzles into the nozzle holder located on the baseplate of the pressure washer.
The label is color-coded for easy placement. There is also a position (if equipped) for an
accessory such as a SIMPSONÂź Turbo Nozzle (purchase separately).
0O15O25O
40OSOAP
The pressure washer does not come with a battery. You must install a U1 sized battery
before using the pressure washer.
1. Remove the cover from the battery box.
2. Carefully place the battery into the battery box.
3. Place the red, positive (+) battery cable onto the positive (+) battery post. Tighten.
4. Place the black, negative (-) battery cable onto the negative (-) battery post. Tighten.
5. Place the cover back onto the battery box.
WARNING! Always remove the black, negative (-) battery cable rst and always
connect the black, negative (-) battery cable last.
Battery connections (if equipped)
Single-cylinder engine with direct-drive pump
Page 8
COMPONENT LOCATION
10. Engine ON/OFF switch
9. Nozzle holders
8. High-pressure pump outlet
7. Spray wand quick connector
6. Detergent hose barb (if equipped)
5. Fuel tank
4. Fuel ller cap
3. Spray gun holder
2. Spray gun trigger lock
1. Spray gun
11. Wheel hand brake
12. Spray gun trigger
3 4 5 6 7
11 10 9 8
21
12
Page 10
Two-cylinder engine with direct-drive pump
3 4 5 6
11 10 9 7
1 2
812
9. Battery box
8. Wheel
7. Spray wand quick connector
6. Oil dipstick
5. Oil ller cap
4. Spark plug
3. Spray gun holder
2. Spray gun trigger lock
1. Spray gun
12. Spray gun trigger
11. Wheel hand brake
10. Engine control station
Page 11
13 14 15 16 17
23 22 21 20 19 18
20. Engine oil lter
19. Engine oil drain plug
18. Fuel tank
17. Fuel ller cap
16. Fuel lter
15. Spark plug
14. Pump
13. Unloader valve knob
22. Garden hose coupler & water inlet lter
21. Thermal relief valve
23. High-pressure pump outlet

Specyfikacje produktu

Marka: Simpson
Kategoria: Myjka wysokociƛnieniowa
Model: SuperPro SW5050HUGL-S

Potrzebujesz pomocy?

Jeƛli potrzebujesz pomocy z Simpson SuperPro SW5050HUGL-S, zadaj pytanie poniĆŒej, a inni uĆŒytkownicy Ci odpowiedzą


Instrukcje Myjka wysokociƛnieniowa Simpson

Simpson

Simpson King Brute 65100 Instrukcja

11 Marca 2025
Simpson

Simpson CM61351 Instrukcja

5 PaĆșdziernika 2024
Simpson

Simpson 95001 Instrukcja

4 PaĆșdziernika 2024
Simpson

Simpson Pro Series PS61374 Instrukcja

2 PaĆșdziernika 2024
Simpson

Simpson 95000 Instrukcja

29 Wrzeƛnia 2024
Simpson

Simpson 95005 Instrukcja

29 Wrzeƛnia 2024
Simpson

Simpson Megashot MS61048-S Instrukcja

26 Wrzeƛnia 2024
Simpson

Simpson Megashot MSH3224-S Instrukcja

26 Wrzeƛnia 2024
Simpson

Simpson Megashot MS60773-S Instrukcja

26 Wrzeƛnia 2024
Simpson

Simpson PowerShot PS3425 Instrukcja

26 Wrzeƛnia 2024

Instrukcje Myjka wysokociƛnieniowa

Najnowsze instrukcje dla Myjka wysokociƛnieniowa

KrÀnzle

KrÀnzle Bully 1180 TST Instrukcja

9 Kwietnia 2025
Nilfisk

Nilfisk Excellent 180 Instrukcja

9 Kwietnia 2025
KrÀnzle

KrÀnzle Therm 895-1 Instrukcja

8 Kwietnia 2025
Topcraft

Topcraft 2000 Instrukcja

7 Kwietnia 2025
Nilfisk-ALTO

Nilfisk-ALTO Poseidon 3 Instrukcja

7 Kwietnia 2025
KrÀnzle

KrÀnzle Quadro 12-150TST Instrukcja

5 Kwietnia 2025
KrÀnzle

KrÀnzle HD 10-122 Instrukcja

5 Kwietnia 2025
Nilfisk-ALTO

Nilfisk-ALTO E 130.1 Instrukcja

5 Kwietnia 2025
Nilfisk

Nilfisk P 160.1 X-TRA Instrukcja

5 Kwietnia 2025
Koblenz

Koblenz HLT-380 V Instrukcja

4 Kwietnia 2025