Instrukcja obsługi Shure WCM16

Shure mikrofon WCM16

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Shure WCM16 (6 stron) w kategorii mikrofon. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/6
1/6
WCM16 -- Headset Condenser Microphone
General Description
The Shure Model WCM16 head-worn electret condenser microphone is intended for wireless use by performers,
lecturers, and others who require the highest quality voice pickup with maximum mobility. Its wide frequency re
sponse, low RF susceptibility and reliable operation at temperature and humidity extremes make the WCM16 suit
able for virtually any vocal application. When used with the Shure Body-Pack Transmitters, the performance of the
WCM16 closely resembles the finest conventional vocal microphones.
Miniaturized active circuitry included in the cartridge assembly provides equalization that tailors the low-frequency
response to resemble the warm proximity effect of larger vocal microphones. Because of this low-end response, it
is not necessary to position the microphone directly in front of the mouth, thus avoiding much popping and breath
noise, even without the supplied foam pop screen.
The microphone's hypercardioid unidirectional pickup pattern provides maximum isolation from ambient noise and
from adjacent sound sources such as musical instruments, loudspeakers and other performers. This permits high
er gain-before-feedback without loss or masking of vocals.
FEATURES:
•Extra lightweight, adjustable headband stays secure and virtually disappears while being worn
•Response comparable to the finest conventional vocal microphones
• Hypercardioid polar pattern provides maximum isolation from vocalist's own instrument and those of other per
formers
•Uniform polar pattern at all frequencies for maximum gain before feedback
•High input clipping level eliminates overload distortion
•Supplied acoustic foam pop screen
•Reliable at temperature and humidity extremes
Wearing the Microphone Headset
1. Place the microphone on the user's head so that the large diameter band is horizontal across the back of the
head. The band may be completely hidden under the hair. The ends of the headband should fit comfortably in
front of the ears. Extend or retract the adjustable headband (see Figure 1) to achieve this result.
2. For maximum gain before feedback, carefully extend or retract the boom (see Figure 1) so that the microphone
grille (silver side) is within 40 mm (1-1/2 in.) of the left corner of the mouth. It may be necessary to bend the
Shure Incorporated
2/6
headband tube just in front of the left ear for optimum microphone positioning. A slight bend downward and/ or
away is usually sufficient.
Note: The headband tubing will not withstand repeated bending, so make this adjustment only once, if neces
sary.
3. If breath noise or popping is audible, install the supplied pop screen so that the red dot on the pop screen cor
responds to the location of the microphone grille.
Figure 1: PARTS OF THE WCM16 HEAD-WORN MICROPHONE
Positioning the Microphone Pickup
The hypercardioid unidirectional pickup pattern of the WCM16 has maximum rejection of unwanted sound sources
at about a 110° angle each way from the front axis of the microphone (see Figure 1). Directly to the rear of the mi
crophone (at 180°) there is as little as 6dB rejection-not much less pickup than at the front of the microphone (at
0°).
Sound sources that may cause feedback (such as monitor or P.A. speakers) or sound that you do not want to pick
up with the WCM16 (such as percussion instruments or other performers) should NOT be placed directly to the
rear of the microphone. It is better to adjust positioning so that unwanted sound sources are located at the 110°
maximum rejection points. Note that when wearing the headset the rear of the microphone points out towards the
wearer's left.
Shure Incorporated
3/6
Connecting to a Transmitter
The WCM16 is configured for direct connection to a Shure Body-Pack Transmitter, such as models T1, T1G, T11,
SC1, EC1, or LX1, using the attached cable.
Microphone Powering
The WCM16 is designed to be powered from the +5 Vdc source at microphone connector pin 2 of a Shure trans
mitter.
Specifications
(Measured using test circuit in Figure 4)
Type
Condenser (electret bias)
Frequency Response
50 to 18,000 Hz
Polar Pattern
Hypercardioid, uniform with frequency
Output Level (close-talked at 1,000 Hz)
Open Circuit Voltage -55.0 (1.8 at 0.6 ) 1 Pascal=94 dB SPL dBV mV m
Maximum Sound Pressure Level
150 at 1%THD dB
Dynamic Range
121 dB
Output Noise
29 equivalent SPL, A-weighted dB

Specyfikacje produktu

Marka: Shure
Kategoria: mikrofon
Model: WCM16

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Shure WCM16, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje mikrofon Shure

Shure

Shure MXA901-R Instrukcja

8 Października 2024
Shure

Shure SBC-DC-903 Instrukcja

5 Października 2024
Shure

Shure SM7dB Instrukcja

29 Września 2024
Shure

Shure MX412SE/C Instrukcja

21 Września 2024
Shure

Shure SBC10-904 Instrukcja

21 Września 2024
Shure

Shure PG27 Instrukcja

20 Września 2024
Shure

Shure TH53 Instrukcja

20 Września 2024
Shure

Shure KSM8 Instrukcja

20 Września 2024
Shure

Shure UA834 Instrukcja

17 Września 2024
Shure

Shure Microflex Overhead MX202 Instrukcja

17 Września 2024

Instrukcje mikrofon

Najnowsze instrukcje dla mikrofon

Audio-Technica

Audio-Technica BP4073 Instrukcja

15 Października 2024
Power Dynamics

Power Dynamics PD524 Instrukcja

15 Października 2024
Audio-Technica

Audio-Technica AT4060 Instrukcja

14 Października 2024
Pyle

Pyle PDWM8225 Instrukcja

13 Października 2024
Sennheiser

Sennheiser ew 100 G4-845-S Instrukcja

13 Października 2024
AKG

AKG WMS420 Instrukcja

13 Października 2024
Audio-Technica

Audio-Technica BP892xCH Instrukcja

12 Października 2024
Apart

Apart MDS.DEL Instrukcja

10 Października 2024
Behringer

Behringer Go Cam Wireless Instrukcja

9 Października 2024
BOYA

BOYA BY-V4 Instrukcja

9 Października 2024