Instrukcja obsługi Shure BETA 52A

Shure mikrofon BETA 52A

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Shure BETA 52A (12 stron) w kategorii mikrofon. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/12
Model BETA 5 2®A Use r Gui de
27D2799 (Rev. 5) Printed in U.S.A.
©2005, Shure Incorporated
SUPERCARDIOID DYNAMIC INSTRUMENT
MICROPHONE
GENERAL
The Shure BETA 52®A is a high output dynamic microphone
with a tailored frequency response designed speci cally for kick fi
drums and other bass instruments. It provides superb attack and
“ ”punch, and delivers studio quality sound even at extremely high
sound pressure levels.
The BETA 52A features a modi ed supercardioid pattern through-fi
out its frequency range to insure high gain before feedback and
excellent rejection of unwanted sound. A built in dynamic locking –
stand adapter with an integral XLR connector simpli es installa-fi
tion, particularly if the microphone is to be placed inside a kick
drum. The stand adapter keeps the microphone position fixed and
resists slipping, even when subjected to sharp blows and strong
vibrations. A hardened steel mesh grille protects the BETA 52A
from the abuse and wear associated with touring.
FEATURES
Frequency response shaped speci cally for kick drums fi
and bass instruments
Built in dynamic locking stand adapter with integral XLR –
connector simpli es setup, especially inside a kick drum fi
Studio quality performance, even at extremely high sound
pressure levels
Supercardioid pattern for high gain before feedback and
superior rejection of unwanted noise
Hardened steel mesh grille that resists wear and abuse
Advanced pneumatic shock mount system that minimizes
transmission of mechanical noise and vibration
Neodymium magnet for high signal to noise ratio output – –
Low sensitivity to varying load impedance
Legendary Shure quality and reliability
•
•
•
•
•
•
•
•
•
APPLICATIONS AND PLACEMENT
The most common BETA 52A applications and placement tech-
niques are listed in the following table. Keep in mind that micro-
phone technique is largely a matter of personal taste there is no –
one correct microphone position.“ ”
Applic ation Suggested Microphone
Placem ent
Tone Quality
Kick Drum 5 to 7.5 cm (2 to 3 in.) away
from beater head, slightly
off-center from beater.
Sharp attack; maximum
bass sound, highest sound
pressure level.
20 to 30 cm (8 to 12 in.)
from beater head, on-axis
with beater.
Medium attack; balanced
sound.
20 to 30 cm (8 to 12 in.)
from beater head, 15 to 20
cm (6 to 8 in.) from edg e
of head.
Medium attack; thin, re-
duced bass sound.
5 to 7.5 cm (2 to 3 in.) away
from outside head, on-axis
with beater (double head
kickdrum o nly).
Softer attack; balanced,
resonant sound.
NOTE: To tighten the “ ”
beat, place a pillow or
blanket on bottom of drum
against beater head.
Electric
Bass Am pli-
fier
2.5 cm (1 in.) from speaker,
on-axis with center of
speaker cone.
Sharp attack; emphasized
bass.
2.5 cm (1 in.) from speaker,
at edge of speaker cone.
Sharp attack; higher fre-
quency sound.
10 to 15 cm (4 to 6 in.) from
speaker, on-axis with center
of speaker cone.
Sharp attack; full, balanced
sound.
60 to 90 cm (2 to 3 ft.) from
speaker, on-axis with center
of speaker cone.
Soft attack; mellow, higher
frequency sound.
MOUNTING THE BETA 52A ON A MICROPHONE STAND
The built in stand adapter features a dynamic locking system –
that permits adjustments to the microphone’s position, but resists
slipping when struck or bumped. To mount the BETA 52A on a
stand and adjust its position, proceed as follows:
Screw the integral stand adapter onto the end of a micro-
phone stand (see Figure 3). Adjust the stand height and
position as necessary.
Pivot the BETA 52A until it is in the desired position rela-
tive to the drum head or loudspeaker.
Lock the BETA 52A in place by rotating the adjustment
knob on the stand adapter clockwise until it is tight. Do
NOT overtighten the knob with tools.
If necessary, make minor adjustments to the microphone
position without loosening the adjustment knob.
Connect an audio cable to the integral XLR connector.
1.
2.
3.
4.
5.
MODEL BETA 52®A
2
SPECIFICATIONS
Type
Dynamic (moving coil)
Frequency Response
20 to 10,000 Hz
NOTE: The curve below shows on axis response at a distance –
of 2 feet from a uniform sound source. Your response may vary,
depending on microphone position
20 200 001000 1000050 100
98765432 98765432
+10
0
–10
Hz
d
B
-20
+
2
0
3 mm
(1/8 in.)
25 mm
(1 in . )
51 mm
(2 in.)
.06 m
(2 ft)
FIGURE 1
Polar Pattern
Supercardioid, rotationally symmetrical about microphone axis
150°
120°
150°
120°
1
8
0
°
30°
60°
90°
30°
60°
0
90°
–10 d B
–20 d B
–15 d B
–5 dB
150°
120°
150°
120°
1
8
0
°
30°
60°
90°
30°
60°
0
90°
–10 dB
–20 dB
–15 dB
–5 dB
500 Hz
1000 Hz
250 Hz 2500 Hz
FIGURE 2
Output Level (at 1,000 Hz)
Open Circuit Voltage: 64 dBV/Pa* (0.6 mV) –
*1 Pa = 94 dB SPL
Impedance
Rated impedance is 150 (45 actual) for connection to Ω Ω
microphone inputs rated low Z
Phasing
Positive pressure on diaphragm produces positive voltage on
pin 2 with respect to pin 3
Maximum SPL
174 dB at 1000 Hz (calculated)
Connector
Three pin professional audio connector (male XLR type) –
Case
Silver blue enamel painted die cast metal with hardened, –
matte- nished steel grille fi
Adjustable, Locking Stand Adapter
Integral, dynamic locking, adjustable through 180 , with stan-°
dard 5/8 -27 thread”
4.451
6.406
3.750
180
STAND
ADAPTER
ADJUSTMENT
KNOB
MICROPHONE
STAND
FIGURE 3
Net Weight
605 grams (21.6 oz)
CERTIFICATION
Eligible to bear CE Marking. Conforms to European EMC
Directive 89/336/EEC. Meets applicable tests and performance
criteria in European Standard EN55103 (1996) parts 1 and 2,
for residential (E1) and light industrial (E2) environments.
FURNISHED ACCESSORIES
Storage Bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26A25
5/8 to 3/8 (Euro) Thread Adapter . . . . . . . . . . . .95A2050 ” ”
OPTIONAL ACCESSORIES
7.6 m (25 ft) Cable . . . . . . . . . . . . . . . . . . . . . . . . .C25E, C25F
REPLACEMENT PARTS
Cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .R175
Screen and Grille Assembly . . . . . . . . . . . . . . . . .RK321
Plug (connector) Assembly . . . . . . . . . . . . . . . . . .90F1984
NOTE: Use care when removing the cartridge holder from the base
to prevent breakage of the lead wires.
For additional Service or parts information, please contact Shure s ’
Service department at 1 800 516 2525. Outside the United – – –
States, please contact your authorized Shure Service Center.
3
MICROPHONE DYNAMIQUE SUPERCARDIO DE POUR Ï
INSTRUMENTS
G N RALIT S É É É
Le Shure BETA 52®A est un microphone dynamique haut niveau à
de sortie pr sentant une courbe de r ponse spé é écialement étudi e é
pour les grosses caisses et autres instruments basse. Il offre –
une attaque et un punch exceptionnels et une qualit de studio, ” ” é
m me dans des conditions de pression acoustique extr me. ê ê
Le BETA 52A maintient une configuration cardio de dans toute sa ï
gamme de fr quences pour assurer un gain lev avant Larsen é é é
et un excellent rejet des bruits ind sirables. Lé ’adaptateur de pied
int gral, ré églable et verrouillable avec connecteur XLR simpli e fi
l installation, en particulier lorsque le micro est plac l int rieur ’ é à ’ é
de la grosse caisse. La grille en acier tremp prot ge le BETA 52A é è
des rigueurs des tourn es. é
AVANTAGES
Courbe de r ponse sp cialement tudi e pour les gros-é é é é
ses caisses et instruments basse. –
L’adaptateur de pied int gral, r glable et verrouillable é é
avec connecteur XLR simpli e l installation, en particulier fi’
lorsque le micro est plac l int rieur de la grosse caisse.é à ’ é
Qualit studio, m me des pressions acoustiques le-é ê à é
v es.é
Con guration supercardio de pour un gain levfiï é é avant
Larsen et rejet sup rieur des bruits ind sirables. é é
Grille en acier trempé r sistante é à l usure et aux mauvais ’
traitements.
Syst me antichocs pneumatique avanc , r duisant la è é é
transmission des bruits m caniques et des vibrations.é
Aimant au néodymium pour un rapport signal/bruit lev .é é
Faible sensibilit aux changements d imp dance de é ’ é
charge.
Qualit et abilit l gendaires de Shure. éfié é
APPLICATIONS ET PLACEMENT
Les applications les plus courantes du BETA 52A sont indiqu es é
dans le tableau ci dessous. Ne pas oublier que la technique de –
placement des micros est surtout une question de go t personnel û
et qu il n y a pas de position correcte . ’ ’ ” ”
•
•
•
•
•
•
•
•
•
Applic ation Placement Sugg ré é Sonorit
Grosse
caisse
5 7,5 cm de la peau de à
frappe, l g rement d cal é è é é
par rapport la batte.à
Attaque franche, basse
maximum, pression acous-
tique maximum.
20 30 cm de la batte, à
dans son axe.
Attaque moyenne, son
é équilibr .
20 30 cm de la batte, 20 à à
30 cm du cerclage.
Attaque moyenne, petit
son, basses r duites.é
5 to 7.5 cm (2 to 3 in.) away
from outside head, on-axis
with beater (double head
kickdrum only).
Attaque douce, son quili-é
br et r sonnant.é é
REMARQUE : pour un son
plus net placer un cous-” ”
sin ou une couverture dans
le bas de la caisse, contre
la peau de frappe
Amp lis d e
basse
électrique
2,5 cm du haut–parleur, au
centre.
Attaque franche, domi-
nance graves.
2,5 cm du haut–parleur, sur
le bord de la membrane.
Attaque franche, son plus
aigu.
10 15 cm du haut par-à –
leur, au centre.
Attaque franche, son plein
et quilibr .é é
60 90 cm du haut par-à –
leur, au centre.
Attaque douce, son plus
aigu.
MONTAGE DU BETA 52A SUR UN PIED DE MICRO-
PHONE
L’adaptateur de pied int gr pr sente un syst me de verrouilla-é é é è
ge dynamique permettant d ajuster la position du microphone ’
tout en emp chant qu il glisse s il est heurteê ’ ’ ’ par les baguettes
du batteur. Pour monter le microphone BET 52A sur un pied et
ajuster la position, proc der comme suit : é
Visser l adaptateur int gr’ é é sur le haut d un pied de micro-’
phone (voir la gure 3). S assurer que la vis de blocage fi’
de l adaptateur est desserr e. R’ é égler a hauteur du pied.
Faire pivoter le microphone BETA 52A jusqu a la position ’
d sir e par rapport a la peau de la caisse ou au hauté é –
parleur.
Serrer la vis de blocage a la main (en la tournant vers la
droite) pour bloquer le microphone en position. NE PAS
serrer la vis en exc s. è
Si n cessaire, modi er l g rement la position du micro-éfié è
phone sans desserrer la vis.
Brancher un c ble de microphone sur le connecteur XLR â
int gré é.
1.
2.
3.
4.
5.
MOD LE BETA 52È
®
A

Specyfikacje produktu

Marka: Shure
Kategoria: mikrofon
Model: BETA 52A

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Shure BETA 52A, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje mikrofon Shure

Shure

Shure MXA901-R Instrukcja

8 Października 2024
Shure

Shure SBC-DC-903 Instrukcja

5 Października 2024
Shure

Shure SM7dB Instrukcja

29 Września 2024
Shure

Shure MX412SE/C Instrukcja

21 Września 2024
Shure

Shure SBC10-904 Instrukcja

21 Września 2024
Shure

Shure PG27 Instrukcja

20 Września 2024
Shure

Shure TH53 Instrukcja

20 Września 2024
Shure

Shure KSM8 Instrukcja

20 Września 2024
Shure

Shure UA834 Instrukcja

17 Września 2024
Shure

Shure Microflex Overhead MX202 Instrukcja

17 Września 2024

Instrukcje mikrofon

Najnowsze instrukcje dla mikrofon

Audio-Technica

Audio-Technica BP4073 Instrukcja

15 Października 2024
Power Dynamics

Power Dynamics PD524 Instrukcja

15 Października 2024
Audio-Technica

Audio-Technica AT4060 Instrukcja

14 Października 2024
Pyle

Pyle PDWM8225 Instrukcja

13 Października 2024
Sennheiser

Sennheiser ew 100 G4-845-S Instrukcja

13 Października 2024
AKG

AKG WMS420 Instrukcja

13 Października 2024
Audio-Technica

Audio-Technica BP892xCH Instrukcja

12 Października 2024
Apart

Apart MDS.DEL Instrukcja

10 Października 2024
Behringer

Behringer Go Cam Wireless Instrukcja

9 Października 2024
BOYA

BOYA BY-V4 Instrukcja

9 Października 2024