Instrukcja obsługi Shark Klik n’ Flip S6001UK

Shark odkurzacz parowy Klik n’ Flip S6001UK

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Shark Klik n’ Flip S6001UK (4 stron) w kategorii odkurzacz parowy. Ta instrukcja była pomocna dla 14 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/4

WHAT’S INSIDE:

For additional parts and accessories, visit sharkclean.eu

QUICK

START

GUIDE

ASSEMBLY

STEAM POCKET® MOP

Use this Quick Start Guide to

learn about your new Shark

Klik n’ Flip Steam Mop’s

great features.

A Steam Mop Handle

B Steam Mop Body

C Klik n’ Flip Mop Head

D Filling Flask

E Dirt Grip™ Pad (x2)

Steam Pocket® Mop Assembly

(Click)

Filling the Water Tank

Pull down on the water tank

cap to open.

Use the ﬁlling ﬂask to pour

water into the tank. Do not

overﬁll. Press the water tank

cap ﬁrmly to close it.

TO REMOVE the Mop Head, press the release

button on the front of the mop body.

Please be sure to read the enclosed Owner’s Guide prior to using your unit.

For questions or to register your product, contact us at:

0800 862 0453 or visit us online at sharkclean.eu

S6001UK_161006

STEAM BLASTER

KLIK N’ FLIP MOP HEAD TECHNOLOGY

IDEAL FOR SEALED FLOORS TROUBLESHOOTING

DIRT GRIP™ PADS

TOUCH-FREE CLEANING PAD ATTACHMENT

USING YOUR STEAM POCKET MOP

With the Klik n’ Flip Mop Head, you can quickly and easily attach and release the Dirt Grip™ Pads

without touching them. No more wrestling with dirty, wet pads. The Dirt Grip Pads are

double sided, washable and reusable. For pad attachment and removal instructions, see

the following page.

Your Steam Mop is ideal for deep cleaning and cutting through

dirt and grime in high-trafﬁc areas.

Plug into an electrical outlet. The blue light will illuminate.

It takes approximately 30 seconds for the mop to heat up

and the steam to be ready.

Pump the handle a few times in a downward motion.

This pumping action will release steam as you mop, and

allows you to customize the amount of steam you want.

Begin mopping with a forward and backward motion.

The natural motion of mopping will produce steam.

3 4

SETTING

IDEAL FOR

THESE SEALED

SURFACES

RECOMMENDED USAGE

MANUAL

Laminate

Hardwood

Marble

Tile

Stone

Cleaning most sealed surfaces and large areas

Basic, everyday cleaning

Removing spots and smaller messes

Cleaning moderate and heavy-trafﬁc areas

STEAM

BLASTER

For an extra burst of steam, you can use the Steam Blaster feature. Follow the

instructions found in the “Steam Blaster” section to the right.

PROBLEM POSSIBLE REASONS & SOLUTIONS

The Steam Mop

isn’t producing

any steam.

The Steam Mop should be securely plugged into an electrical outlet.

Check your fuse or circuit breaker or try a different outlet.

Make sure the water tank is full, the unit is plugged in, and the blue

light is illuminated steadily.

If the blue light is not illuminated, try a different electrical outlet.

Pump the handle a few times to activate steam.

If after following the above steps the Steam Mop still does not

produce any steam, contact Customer Service at 0800 862 0453.

The Steam Mop

is producing

intermittent

steam.

Make sure the water tank is full.

I am getting

streaky/cloudy

ﬂoors.

The Dirt Grip™ Pad might be dirty. If it is, ﬂip it over to the clean side

or change it entirely. If you washed the Dirt Grip Pad with powdered

detergent, then it could be damaged and require replacement.

This could also be an indication of soap or grease residue that has

accumulated on the ﬂoor. As the Steam Mop uses only a small amount of

water, it may not be enough to rinse off the accumulation of residue that

the steam is bringing to the surface. We suggest rinsing the ﬂoor with

nothing but water, letting it dry, and then steam mopping again with a clean

Dirt Grip Pad. One or more rinses will generally remove the residue.

A more stubborn case may require you to rinse the ﬂoor with a mix of

one part vinegar and two parts water* (but DO NOT put any cleaning

solutions or chemicals into the Steam Mop’s water tank.)

* Please consult your ﬂooring manufacturer’s care and maintenance

instructions before applying any cleaning products or solutions.

It’s really hard

for me to

push/pull the

Steam Mop.

The Steam Mop might be hard to push/pull if the Dirt Grip Pad isn’t wet

enough. It should get easier to push/pull the Steam Mop after it’s been

running for a few minutes.

An overly dirty pad could also result in a harder push/pull experience.

We recommend ﬂipping the pad over or using a clean pad.

DOUBLE SIDED, WASHABLE, REUSABLE

Our washable Dirt Grip Pads are made with ﬁbers specially designed to absorb and trap dirt.

This gives your ﬂoors an amazing clean, with minimal streaking and short dry times.

For best cleaning results, we recommend replacing your

Dirt Grip Pads following 20 normal uses.

CLEANING PAD CARE

Machine wash the Dirt Grip Pads separately with warm

water using liquid detergent.

NEVER USE BLEACH, POWDERED DETERGENT,

OR FABRIC SOFTENERS as they may damage

the Dirt Grip Pads.

You can purchase replacement Dirt Grip Pads

and other accessories by visiting sharkclean.eu

or calling 0800 862 0453.

Some parts may be available at your local retailer.

Contact Customer Service for any other servicing.

When you need an extra burst

of steam to clean tough, dried

messes and stuck-on stains,

use the Steam Blaster.

1. Flip the Mop Head over so

that it is behind

the mop body.

2. Tilt the mop handle

back. This will cause the

Steam Blaster to emit

a concentrated blast of

steam onto the ﬂoor.

To stop the Steam Blaster

spray, simply tilt the mop

handle forward.

4. Flip the Mop Head

back into its

original position and

continue cleaning.

1. Lift the mop straight up by the handle

until the Mop Head is hanging straight

down. Center the Mop Head above the

pad. Press the release button on the back

of the mop body, and both sides of the

mop head will drop open.

1. L ift the mop straight up by the

handle until the Mop Head is

hanging straight down. Press

the pad release button, and both

sides of the head will drop open,

releasing the pad.

3. Gently press the Mop Head to the ﬂoor on

one side of the pad, and that side will click

into place.

4. Flip the other side of the head over onto

the ﬂoor to click into place.

REMOVING THE CLEANING PAD

2. Slip the mop head’s 4 corner tabs into the

4 corner pockets of the Dirt Grip™ Pad.

Specyfikacje produktu

Marka:	Shark
Kategoria:	odkurzacz parowy
Model:	Klik n’ Flip S6001UK
Kolor produktu:	Stal nierdzewna
Liczba źródeł światła:	2 szt.
Rodzaj żarówki:	LED
Materiał obudowy:	Stal nierdzewna
Typ kontroli:	Przyciski
Wbudowany wyświetlacz:	Nie
Częstotliwość wejściowa AC:	50 Hz
Napięcie wejściowe AC:	220 - 240 V
Szerokość produktu:	900 mm
Głębokość produktu:	500 mm
Waga produktu:	9300 g
Szerokość opakowania:	955 mm
Wysokość opakowania:	320 mm
Głębokość opakowania:	560 mm
Poziom hałasu:	72 dB
Obciążenie:	168 W
Klasa wydajności energetycznej:	A
Skala efektywności energetycznej:	A +++ do D
Waga wraz z opakowaniem:	11000 g
Lampy:	1.5 W
Instrukcja szybkiej instalacji:	Tak
Model:	Naścienny
Roczne zużycie energii:	40 kWh
Prędkości:	3
Możliwość mycia filtra:	Tak
Zestaw do montażu:	Tak
Maksymalna moc ekstrakcji:	- m³/h
Rodzaj ekstrakcji:	Kanałowe / obiegowe
Klasa wydajności przepływu dynamicznego:	A
Klasa wydajności świecenia:	A
Klasa skuteczności filtra przeciwtłuszczowego:	C
Poziom hałasu (niska prędkość):	68 dB
Rodzaj filtra tłuszczu:	Aluminium
Filtr odporny na zmywanie w zmywarce:	Tak
Zdjemowalny filtr:	Tak
Moc silnika:	- W
Wysokość (min):	635 mm
Wysokość (max.):	1025 mm
Silnik dołączony:	Tak
Ilość silników:	1
Poziom hałasu (wysoka prędkość):	72 dB
Liczba filtrów:	3 szt.
Maksymalna moc recyrkulacji:	621 m³/h