Instrukcja obsługi SentrySafe QAP1BE
SentrySafe
Kluis
QAP1BE
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla SentrySafe QAP1BE (17 stron) w kategorii Kluis. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/17
QAP1E
QAP1BE
Quick Access Pistol Safe
Owner’s Manual
2
Table of ContentsWarnings
WARNING
SentrySafe recommends that you do not store guns in this unit.loaded
NOTICE
YOUR SAFE IS ONLY PART OF YOUR TOTAL SECURITY PROTECTION.
SentrySafe recommends that you store your safe in a closet, office, basement, bedroom or any
other location that is convenient for you but out of direct line of sight from prying eyes.
The location of the safe does not affect the safe’s ability to protect your valuables inside.
This is a California-approved firearm safety device that meets the requirements of Penal Code
section 23655 and the regulations issued thereunder.
1 2 3 4
4
NOTE: Store code and keys in a secure location (other than in the safe).
NOTE: SentrySafe offers a secure on-line location for the entry and retrieval of your code.
Go to and register your safe. www.registermysafe.com
Insert key into keyhole and turn clockwise.
NOTE: Do not lock key inside safe – this is an override key and will
open the safe in the event that you have lost your code.
A Remove the battery pack cover.
B Pull out battery pack (keep battery pack connected
to wires).
C Insert four NEW AA alkaline batteries.
IMPORTANT
All safe models initially work with the factory code 1, 2, 3, 4, 1. It is therefore
important to re-program your safe with a new user code you have personally
selected to provide maximum security.
The Quick Access Pistol Safe comes with a built-in code.
Factory code 1, 2, 3, 4, 1.
Press any button once to bring the safe out of standby mode, then
enter the Factory Code 1, 2, 3, 4, 1.
The Green LED will light.
To Program an Electronic Code
A Find the Reset button located behind the battery pack.
B Press and hold the Reset button until the keypad flashes 3 times.
The LEDs remain on to indicate it is ready to accept a new user code.
C Enter a user code that is four, five or six digits long.
D A successful programming of the user code is indicated when the
LED light flashes green three times.
Programming Your Safe
Preparing your safe for first-time use
Programming your safe
Programming Your Safe
NOTE: Do not use rechargeable batteries or any other type of non-alkaline battery.
Do not mix old and new batteries. Do not mix alkaline and standard batteries.
A
Specyfikacje produktu
Marka: | SentrySafe |
Kategoria: | Kluis |
Model: | QAP1BE |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z SentrySafe QAP1BE, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Kluis SentrySafe
2 Października 2024
2 Października 2024
2 Października 2024
2 Października 2024
2 Października 2024
2 Października 2024
2 Października 2024
2 Października 2024
2 Października 2024
2 Października 2024
Instrukcje Kluis
- Kluis Thule
- Kluis Honeywell
- Kluis Perel
- Kluis Juwel
- Kluis Master Lock
- Kluis Kidde
- Kluis First Alert
- Kluis Olympia
- Kluis Hama
- Kluis Yale
- Kluis SereneLife
- Kluis Workzone
- Kluis Avanti
- Kluis Burg Wächter
- Kluis Guzzanti
- Kluis Toolland
- Kluis Salvus
- Kluis Hard Head
- Kluis Steren
- Kluis Royal Sovereign
- Kluis Phoenix
- Kluis Topcraft
- Kluis Varo
- Kluis CAWI
- Kluis Rottner
- Kluis Sentry
- Kluis Filex
- Kluis Kreator
- Kluis Handson
- Kluis Royal Safe
- Kluis Jewel
- Kluis Sistec
- Kluis SMC
- Kluis FireKing
- Kluis Rottner Tresor
- Kluis Olymp
- Kluis Protector
- Kluis Homak Security
- Kluis Technomax
Najnowsze instrukcje dla Kluis
1 Października 2024
1 Października 2024
1 Października 2024
1 Października 2024
1 Października 2024
30 Września 2024
30 Września 2024
30 Września 2024
30 Września 2024
30 Września 2024