Instrukcja obsługi SE Electronics Z5600a II

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla SE Electronics Z5600a II (32 stron) w kategorii mikrofon. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/32
Z5600a II
U s e r M a n u a l
2
User Manual - EN
Thank you
Thank you for choosing an sE microphone! In addition to some basic safety precautions, this manual includes details
and specifications that we hope will assist you in getting the most out of your Z5600a II. Please take a few minutes to
read through it.
Capturing great audio is our passion. We sincerely hope youll enjoy the sound of this mic as much as we enjoyed
designing and building it for you.
Happy Tracking,
The sE Team
Brief Description
The tone quality and versatility of the Z5600a II make it an asset to any mic locker. -This large diaphragm condenser
microphone has nine switchable polar patterns, ranging from omnidirectional to cardioid to figure-8, with six additional
patterns in between. Central to the Z5600a II’s rich timbre is a 12AX7 tube, delivering stunning detail and flattering the
source with enhanced harmonic character. In other words, this mic sounds huge! It has been praised for capturing
incredible vocal tones, but the Z5600a II is engineered to excel in any sonic context.
The Z5600a II is equipped with a switchable low cut filter, as well as a switchable -10dB pad, making it just as suitable
for recording a string quartet, or drum overheads, as it is for tracking vocals.
Like all of our microphones, the Z5600a II is built by hand at sE Headquarters in Shanghai. We take pride in the attention
to detail under which our products are crafted, therefore the entirety of manufacturing is done in our own facilities. We
also individually test and measure the tubes for these mics to ensure optimal performance upon arrival.
What’s in the box
Your Z5600a II includes a custom flight case to safely transport the microphone and its necessary accessories. If
anything is missing, please contact your sE Electronics dealer f or assistance.
Z5600a II microphone
8- pin microphone cable
Custom shockmount
Power supply
IEC power cable
Controls
The Z5600a II -features both an Attenuation Switch and a Low Cut Switch.
Attenuation Switch
The Attenuation Switch is located on the front-left side of the microphone. When engaged, the
incoming signal is reduced by 10dB, helping prevent signal distortion preamplifier clipping and
when capturing audio at close proximity and/or high sound pressure levels.
3
Low-Cut Switch
The Low-Cut Switch is located on the front a low-right side of the microphone, inserting -cut filter
at 5 . 0Hz when engaged When switched to the left, the filter is removed for a flat frequency
response. This low-cut switch is useful for reducing plosives, footfall noise, and especially rumble
that might adversely affect the recorded signal. Additionally, the -low cut filter will help minimize
the proximity effect when “close-miking,i.e. placing the microphone a very short distance from
the source.
Pattern Switch
The Pattern Switch is located front and center on the microphone’s power supply. This 9-
position switch allows a range of polar patterns from omnidirectional (left,) to cardioid (middle,)
to figure 8 (right.) There are six pattern variations available between these three. This array of
patterns makes it possible to tailor the balance of direct sound, versus ambient sound, that the
microphone picks up.
Powering
The included floor box contains the outboard power supply for the Z5600a II. No phantom power is required from an
interface or microphone preamplifier.
Before powering on, connect all required cables (IEC to power, XLR to preamplifier or interface, and 8-pin cable from
floor box to microphone). Then turn the power on via the switch on the back of the Z5600a II floor box.
For best performance, we recommend allowing approximately 15 minutes of warm up” time before recording. This
allows the tubes within the Z5600a II to heat up and stabilize, and reduces the risk of unwanted noise or distortion on
your recordings.
Risk of damage
Do not connect the microphone to any power supply other than the included Z5600a II power
supply. Do not apply phantom voltage (+48VDC) from an external interface or preamplifier.
This is the only way to ensure safe and reliable operation.
Safety and maintenance
Risk of damage
Please make sure that the piece of equipment to which your microphone and PSU will be
connected fulfils the safety regulations enforced in your country and is fitted with a ground
lead.
Cleaning icroph the m one
The microphone d in the supplied should only be cleaned with a dry, soft cloth. It is best store wooden presentation box.

Specyfikacje produktu

Marka: SE Electronics
Kategoria: mikrofon
Model: Z5600a II

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z SE Electronics Z5600a II, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje mikrofon SE Electronics

SE Electronics

SE Electronics V7 BFG Instrukcja

8 Października 2024
SE Electronics

SE Electronics V7 V3 Instrukcja

8 Października 2024
SE Electronics

SE Electronics T1 Instrukcja

3 Października 2024
SE Electronics

SE Electronics DM2 TNT Instrukcja

3 Października 2024
SE Electronics

SE Electronics sE4100 Instrukcja

2 Października 2024
SE Electronics

SE Electronics V7 MC2 Instrukcja

2 Października 2024
SE Electronics

SE Electronics V7 MC1 Instrukcja

2 Października 2024
SE Electronics

SE Electronics VR2 Instrukcja

2 Października 2024

Instrukcje mikrofon

Najnowsze instrukcje dla mikrofon

Audio-Technica

Audio-Technica BP4073 Instrukcja

15 Października 2024
Power Dynamics

Power Dynamics PD524 Instrukcja

15 Października 2024
Audio-Technica

Audio-Technica AT4060 Instrukcja

14 Października 2024
Pyle

Pyle PDWM8225 Instrukcja

13 Października 2024
AKG

AKG WMS420 Instrukcja

13 Października 2024
Audio-Technica

Audio-Technica BP892xCH Instrukcja

12 Października 2024
Apart

Apart MDS.DEL Instrukcja

10 Października 2024
BOYA

BOYA BY-V4 Instrukcja

9 Października 2024