Instrukcja obsługi Scosche GM20SRB

Scosche Niesklasyfikowane GM20SRB

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Scosche GM20SRB (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
GM20SR
CADILLAC CTS/SRX RADIO REPLACEMENT
INSTALLATION INSTRUCTIONS
The GM20SR is a plug and play interface that allows replacement of a General Motors Class II factory stereo in
Cadillac CTS and SRX vehicles. It will maintain operation of the OnStar® and factory amplified systems. The
GM20SR has on board switching to allow audio from the OnStar
® system to play through the two front factory
speakers when OnStar® is active. It also retains warning chimes for Onstar
® operation. For additional vehicle
integration, use Scosche’s line of SWC-1 steering wheel controls (SWC) interfaces to retain SWC’s with the
aftermarket radio. Also retains Vehicle Parking Assist chimes.
• Class II circuitry will not disable vehicle data bus even if interface loses power.
• OnStar® active LED and Ignition on LED
• Provides +12v switched accessory output. No more searching for switched +12v in fuse box or kick panel.
• Mute output to either mute the aftermarket radio or to turn it off when OnStar
® is active.
• OnStar® Volume control via factory steering wheel audio controls or click wheel .
• New radio will operate with the vehicle RAP (Retained Accessory Power) system, stays on after the key is turned
off and for 10 minutes or until a door is opened.
NOTE:
1. The GM20SR does not retain the factory XM receiver, you will lose this option when the factory radio is
replaced with an aftermarket radio.
2. You may use this interface even if the vehicle does not have OnStar® but need to the interface to operate the
factory amplifier.
3. OnStar® must be enabled using the OnStar® button on the rear view mirror, steering wheel OnStar
® button will
not enable OnStar®.
4. OnStar® volume is not adjustable on CTS-V and SRX models, volume is preset at medium level.
5. Not compatible with SRX Factory Navigation Radios.
SUPPORTED VEHICLES
INSTALLATION
2003-2007 CTS Compatible with both Navigation and Non-Navigation Radios
2004-2007 SRX Compatible with Non-Navigation Radios. Not Compatible with Navigation Radios.
NOTE: New vehicles are constantly being researched. If your vehicle is not listed above, check our web site for
any new updates or instructions.
CONNECTING THE GM20SR
NOTE: Due to the design of the Standard Amplified system, there is currently no way of fading from front to rear
with an aftermarket radio.
NOTE: If using a SWC-1 SWC-1 (SWC), the green wire on the is connected to the red wire of the red 20-pin
harness. SWC-1 must be programmed for Version #1.
Step 1. Prewire the GM20SR 18-pin wire harness to the aftermarket stereo wire harness. If the aftermarket stereo
has a mute wire, cut the brown wire as close as possible to pin #16 of the GM20SR 18-pin harness and connect
this mute output wire to the stereo’s mute wire. The amp remote wire (Blu/Wht) must be connected to the stereo’s
remote wire. Connect the 16-pin wire harness to the GM20SR main interface.
Step 2. Connect the black 8-pin, brown 8-pin, and the red 20-pin harness to the factory radio harnesses. Connect
the 16-pin wire harness into the GM20SR.
TESTING AND VERIFYING OPERATION
1. Turn ignition on. The red ignition LED on the side of the interface will turn on and the +12v accessory wire will
turn on.
2. Turn on the radio and check the balance. NOTE: Audio will not fade as the rear outputs of aftermarket radio can
not be used.
3. Pressing the OnStar® button on the mirror will mute or turn off the radio and allow the audio to be heard from
the speakers. The OnStar
® active red LED will also turn on. When OnStar
® disconnects, the radio will un-mute
or turn back on and the OnStar
® LED will turn off. OnStar® audio level can be adjusted using the volume
controls on the steering wheel (volume level is preset for CTS-V and SRX vehicles)
4. Turn off vehicle and remove key. RAP will be active and keep the radio on for 10 minutes or until a door is
opened.
5. The red LED and radio will turn off when RAP turns off or door is opened.
DISCLAIMER
In no event shall Scosche be responsible for claims beyond the replacement value of the defective product, or in any way liable
or responsible for consequential or incidental damages.
If you have any further questions call: TECH HELP 1-800-621-3695x3
©2007 SCOSCHE INDUSTRIES, INC. GM20SR 4/06 (3000003)
CONNECTING THE GM20SR
LOOKING FROM WIRE SIDE OF PLUGS
16-PIN GM20SR OUTPUT HARNESS 18-PIN GM20SR INPUT HARNESS

Specyfikacje produktu

Marka: Scosche
Kategoria: Niesklasyfikowane
Model: GM20SRB

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Scosche GM20SRB, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Scosche

Scosche

Scosche ITCFD05AB Instrukcja

22 Września 2024
Scosche

Scosche FT4275B Instrukcja

22 Września 2024
Scosche

Scosche PSM21000 Instrukcja

22 Września 2024
Scosche

Scosche SU2029B Instrukcja

22 Września 2024
Scosche

Scosche IPD2CFBK Instrukcja

22 Września 2024
Scosche

Scosche EFX PA10BX Instrukcja

22 Września 2024
Scosche

Scosche SI-2227B Instrukcja

22 Września 2024
Scosche

Scosche PBJ300 Instrukcja

22 Września 2024
Scosche

Scosche EFX PA4BX Instrukcja

22 Września 2024
Scosche

Scosche ITCLS01B Instrukcja

21 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

GBC

GBC ThermaBind T500Pro Instrukcja

15 Stycznia 2025
Da-Lite

Da-Lite Parallax 29850 Instrukcja

15 Stycznia 2025
Crivit

Crivit IAN 290909 Instrukcja

15 Stycznia 2025
Tripp Lite

Tripp Lite SmartRack SRW12US Instrukcja

15 Stycznia 2025
Powerfix

Powerfix IAN 280221 Instrukcja

15 Stycznia 2025
AGM

AGM Rattler TC35-640 Instrukcja

15 Stycznia 2025
AGM

AGM Wolf-7 Pro Instrukcja

15 Stycznia 2025
AGM

AGM Anaconda TC50-640 Instrukcja

15 Stycznia 2025
AGM

AGM Secutor Pro TS50-640 Instrukcja

15 Stycznia 2025
Microchip

Microchip AT91SAM9M11 Instrukcja

15 Stycznia 2025