Instrukcja obsługi Scosche GM1482R

Scosche Niesklasyfikowane GM1482R

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Scosche GM1482R (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
SHAFT
RADIO
SNAP
SHAFT
TABS
MOUNTING
PANEL
IN-DASH INSTALLATION KIT FOR
1988-94 GENERAL MOTORS
1500 SERIES FULL SIZE TRUCKS
TECH HELP 1-800-621-3695x3
SI 6/03 - GM1482 (3000156)© 2003 SCOSCHE INDUSTRIES, INC.
LIABILITY DISCLAIMER
This instruction booklet is based on carefully documented data and research of automobile dash disassembly, wire harness/
codes and information pertaining to installation of this kit (GM1482) in 1988-94 GM Vehicles. Scosche Industries, Inc. can not
be held responsible for discrepancies/inconsistencies that may occur due to the automobile manufacturing changes or
options, or damage that may occur in the automobile during the installation of components while using this booklet.
Vehicle Applications:
CHEVROLET / GMC
1992-94 BLAZER - FULL SIZE
1992-94 CREW CAB DOOLEY PICKUP
1988-94 PICKUP - FULL SIZE
1992-94 SUBURBAN
1992-94 YUKON
GM1482
If you have any further questions, call
NOTE: Scosche MDA-1 antenna adapter
and GM02 factory connector (sold
separately) are needed to
complete the installation.
ILLUSTRATION A
CAUTION:
Disconnect your vehicle's negative battery terminal before the installation to help prevent electrical
Damage. We recommend the use of a volt/ohm meter over a test light to check wiring. A test light or
grounded wire probe can cause damage to the vehicle's computer and/or diagnostic systems. Avoid all
factory air bag wiring - air bags can accidentally deploy causing serious injury or death.
NOTES:
See your vehicle's instructions for any special tools your installation might require. Read all instructions
accompanying your car stereo/cassette player for proper wiring and mounting instructions.
INTRODUCTION/PRELIMINARYINTRODUCTION/PRELIMINARY
INTRODUCTION/PRELIMINARYINTRODUCTION/PRELIMINARY
INTRODUCTION/PRELIMINARY
FACTORY WIRE CODES
For Factory Wiring Codes go to: www.scosche-cars.com
MOUNTING
SLEEVE
DIN
RADIO
RADIO'S
SUPPLIED
TRIMPLATE
MOUNTING
PANEL
TAPE PLAYER/EQUALIZER REMOVAL
AND CAVITY PREPARATION:
1. Carefully remove the factory bezel by prying out along the bottom to release fastening clips. Then
carefully pull down on the bezel to release the fasteners securing the top and remove the bezel.
2. Extract the two (2) screws securing the factory tape player/equalizer (when equipped).
3. Remove the dash panel under the steering column by extracting the two (2) screws securing it to
the dash.
4. Locate and remove the radio tuner pack under the dash above the acceleator pedal by extracting
the three (3) screws securing it to the dash.
5. Unplug all the connectors going into the radio tuner pack and remove it from the vehicle.
6. Pull the tape player/equalizer from the dash, carefully pull the plug harness through the dash from
the radio tuner pack location and remove the tape player/equalizer from the dash.
7. Locate the antenna plug and the three plugs that were connected to the top of the radio tuner pack.
Route them into the tape player/equalizer cavity. These are the factory power, speaker and antenna
plugs that will be used for the aftermarket radio hook-ups.
DIRECTIONS
ILLUSTRATION C
REAR
VIEW
OF KIT
ILLUSTRATION B
METAL
FASTENING
CLIP
GM1482 KIT PREPARATION:
1. Remove the metal fastening clips from the
bottom of the factory dash bezel and attach
them to the same location on the GM1482
kit. (See Illustration B)
2. Remove the A/C vents from the factory dash
bezel by releasing the spring fastening clips
securing them into the bezel.
3. Mount the vents into the kit by inserting the
inner edge of the vent into the center
alignment slot then insert the outer edge of
the vent into the outer alignment slot. Using
the same spring clips and mounting
procedures that were used to mount the
vents to the factory dash bezel, mount the
vents to the kit.
STEREO INSTALLATION:
1. Install the GM1482 kit into the dash by
inserting the top mounting clips into the slots
in the dash and pushing up to snap them in.
Then press the bottom clips into the slots at
the bottom of the dash to secure the kit to the
dash.
2. Connect the stereo to the factory plugs
(see Wire Codes) as directed in the
stereo installation manual.
3. Mount the stereo into the GM1482 kit as
shown in Illustration C for DIN or
llustration A for shaft.

Specyfikacje produktu

Marka: Scosche
Kategoria: Niesklasyfikowane
Model: GM1482R

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Scosche GM1482R, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Scosche

Scosche

Scosche ITCFD05AB Instrukcja

22 Września 2024
Scosche

Scosche FT4275B Instrukcja

22 Września 2024
Scosche

Scosche PSM21000 Instrukcja

22 Września 2024
Scosche

Scosche SU2029B Instrukcja

22 Września 2024
Scosche

Scosche IPD2CFBK Instrukcja

22 Września 2024
Scosche

Scosche EFX PA10BX Instrukcja

22 Września 2024
Scosche

Scosche SI-2227B Instrukcja

22 Września 2024
Scosche

Scosche PBJ300 Instrukcja

22 Września 2024
Scosche

Scosche EFX PA4BX Instrukcja

22 Września 2024
Scosche

Scosche ITCLS01B Instrukcja

21 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024