Instrukcja obsługi Sanus NFCD


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Sanus NFCD (5 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 25 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/5
Assembly Instructions for Model: NFCD
Thank you for choosing a Sanus Systems Natural Media Tower. The Model
NFCD is designed to keep your collection clean and organized by storing up to
430 CDs or 230 DVDs, all in one convenient location.
If you do not understand these directions, please contact Sanus at 800.359.5520
or www.sanus.com. Check carefully to make sure that there are no missing or
defective parts. Our customer service representatives can quickly assist you
with assembly questions, and missing or damaged parts. Replacement parts
for products purchased through authorized dealers will be shipped directly to
you. Never use defective parts. Improper assembly may cause damage or
serious injury. Do not use this product for any purpose that is not explicitly
specied by Sanus Systems. Sanus Systems can not be liable for damage
or injury caused by incorrect assembly, or incorrect use. Please call Sanus
Systems before returning products to the point of purchase.
Required Tools: Rubber mallet or hammer, screwdrivers, phillips & regular
Supplied Parts List: (Not to Scale)
NFCD Top - A
Qty. 1
Glass Shelves - F
Qty. 14
NFCD Base - B
Qty. 1
Center Support - D
Qty. 1
Side Panels - E
Qty. 2
NFCD Foot - C
Qty. 4
Sanus Name Plate - G
Qty. 1
Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 02.28.06 (100028)
Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com
Supplied Hardware: (Full Size)
Step 1 - Attach Feet to NFCD Base
Insert a Machine Screw ( ) into each Foot ( ); then using the regular screwdriver, attach the Feet to the NFCD Base ( ). K C B
Diagram 1
Cam - H
Qty. 4
Cam Pin - I
Qty. 4
Plastic Dowel - J
Qty. 4
Wood Screw - L
Qty. 4
Machine Screw - K
Qty. 4
Shelf Pin - M
Qty. 56
B
K
C
C
C
C
K
K
K
Step 2 - Insert Cam Pins into Side Panels
There are two holes that are centered on each side of the Side Panels ( ), and 12” [304.3 mm] from each end. Using E
the phillips screwdriver, screw Cam Pins ( ) into the two holes of each Side Panel taking care not to over tighten the Cam I
Pins.
Diagram 2
E
I
E
Step 3 - Insert Cam into Center Support.
Place a Cam ( ) into each of the four holes in the Center Support ( )H D
NOTE: Each Cam has an arrow on it. Using a phillips screwdriver align each Cam so the arrow is pointing toward
the small hole on the edge of the Center Support (See Detail - A).
Diagram 3
Step 4 - Secure Side Panels to Center Support.
The Cam Pins ( ) installed in each Side Panel ( ) line up with the small holes in the edge of the Center Support ( ). The top I E F
of each Side Panel is smooth and the bottom has a notch routed in the inside edge.
Attach a Side Panel to each side of the Center Support and using a phillips screwdriver, rotate each Cam ( ) clockwise until H
tight (See Detail - B).
Diagram 4
D
Small Hole
Cam Hole
Cam - H
Small
Hole
Cam - H
Detail - A
Top
Smooth
Bottom
Notched
I
H
E
E
F
Detail -B


Specyfikacje produktu

Marka: Sanus
Kategoria: nieskategoryzowany
Model: NFCD

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Sanus NFCD, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje nieskategoryzowany Sanus

Instrukcje nieskategoryzowany

Najnowsze instrukcje dla nieskategoryzowany

Meec Tools

Meec Tools 010-084 Instrukcja

6 Października 2024
Outwell

Outwell Scenic Road 250 Instrukcja

5 Października 2024
Impact

Impact QuikBalance Instrukcja

4 Października 2024
Impact

Impact CA-112 Instrukcja

4 Października 2024
Impact

Impact LS-BHA Instrukcja

4 Października 2024
Impact

Impact LKB-5C Instrukcja

4 Października 2024
Impact

Impact RST-001 Instrukcja

4 Października 2024