Instrukcja obsługi Samsung WA10J7700GW

Samsung pralka WA10J7700GW

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Samsung WA10J7700GW (60 stron) w kategorii pralka. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/60
Washer
User manual
WA10J7700G*
SSEC SEC
WA7700J_WA10J7700GW-03520R-04_SA.indd 1 2016/5/12 11:20:21
2 English
Contents
Contents
Safety information 4
What you need to know about the safety instructions 4
Important safety symbols 4
Important safety precautions 5
Installation 11
Unpacking your washer 11
Overview of your washer 12
Basic location requirements 14
Important note to installer 18
Step-by-step installation 18
Operating instructions 26
Loading your washer 26
Getting started 27
Washing a load of laundry 28
Control panel 28
Cycle overview 29
Options 30
Washing clothes using the cycle selector 33
ATC (Auto Temperature Control) 34
The basics 35
Detergent use 37
Features 38
Maintaining your washer 41
Cleaning the exterior 41
Cleaning the interior 41
Storing your washer 41
Preserving the top cover and the front frame 42
Cleaning the built-in sink and lint lter 42
Cleaning the dispensers 43
Tub clean 45
Troubleshooting 46
Checkpoints 46
Information codes 50
WA7700J_WA10J7700GW-03520R-04_SA.indd 2 2016/5/12 11:20:21
English 3
Contents
Specications 53
Fabric care chart 53
Helping the environment 55
Specication sheet 56
Cycle chart 57
WA7700J_WA10J7700GW-03520R-04_SA.indd 3 2016/5/12 11:20:21
4 English
Safety information
Safety information
Congratulations on your new Samsung washer. This manual contains important information
on the installation, use and care of your appliance. Please take some time to read this manual
to take full advantage of your washer’s many benets and features.
What you need to know about the safety instructions
Please read this manual thoroughly to ensure that you know how to safely and efciently
operate the extensive features and functions of your new appliance. Please store the manual
in a safe location close to the appliance for future reference. Use this appliance only for its
intended purpose as described in this instruction manual.
Warnings and Important Safety Instructions in this manual do not cover all possible
conditions and situations that may occur. It is your responsibility to use common sense,
caution and care when installing, maintaining and operating your washing machine.
Because the following operating instructions cover various models, the characteristics of your
washing machine may differ slightly from those described in this manual and not all warning
signs may be applicable. If you have any questions or concerns, contact your nearest service
centre or nd help and information online at www.samsung.com.
Important safety symbols
What the icons and signs in this user manual mean:
WARNING
Hazards or unsafe practices that may result in severe personal injury, death and/or property
damage.
CAUTION
Hazards or unsafe practices that may result in personal injury and/or property damage.
NOTE
Indicates that a risk of personal injury or material damage exists.
WA7700J_WA10J7700GW-03520R-04_SA.indd 4 2016/5/12 11:20:21
English 5
Safety information
These warning signs are here to prevent injury to yourself and others.
Please follow them explicitly.
After reading this manual, store it in a safe place for future reference.
Read all instructions before using the appliance.
As with any equipment that uses electricity and moving parts, potential hazards exist. To
safely operate this appliance, familiarize yourself with its operation and exercise care when
using it.
Important safety precautions
WARNING
T
o reduce the risk of re, electric shock, or injury to persons when
using your appliance, follow basic precautions, including the following:
Do not let children (or pets) play in or on your washing machine.
The washing machine door does not open easily from the inside and
children may be seriously injured if trapped inside.
This appliance is not to be used by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their
safety.
Children should be supervised to ensure that they do not play with the
appliance.
For use in Europe: This appliance can be used by children aged from 8
years and above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the appliance in a
safe way and understand the hazards involved. Children shall not play
with the appliance. Cleaning and user maintenance shall not be made
by children without supervision.
WA7700J_WA10J7700GW-03520R-04_SA.indd 5 2016/5/12 11:20:21
6 English
Safety information
Safety information
If the supply cord is damaged, it must be replaced by the manufacturer,
its service agent or similarly qualied persons in order to avoid a
hazard.
This appliance should be positioned so that the power plug, the water
supply taps, and the drain pipes are accessible.
For appliances with ventilation openings in the base, that a carpet must
not obstruct the openings.
The new hose-sets supplied with the appliance are to be used and that
old hose-sets should not be reused.
CAUTION
In order to avoid a hazard due to inadvertent resetting of the thermal
cut-out, this appliance must not be supplied through an external
switching device, such as a timer, or connected to a circuit that is
regularly switched on and off by the utility.
CAUTION
Do not use the water to exceed 50 °C when using the hot water in your
washing machine.
Plastic parts may be deformed or damaged, and this may result in
electric shock or re.
Critical installation warnings
WARNING
The installation of this appliance must be performed by a qualied technician or service
company.
• Failure to do so may result in electric shock, re, an explosion, problems with the product,
or injury.
WA7700J_WA10J7700GW-03520R-04_SA.indd 6 2016/5/12 11:20:21
English 7
Safety information
Plug the power cord into an AC 220-240 V / 50 Hz wall socket or higher and use the socket
for this appliance only. Never use an extension cord.
• Sharing a wall socket with other appliances using a power strip or extending the power
cord may result in electric shock or re.
• Ensure that the power voltage, frequency, and current are the same as those of the
product specications. Failure to do so may result in electric shock or re. Plug the power
plug into the wall socket rmly.
Remove all foreign substances such as dust or water from the power plug terminals and
contact points using a dry cloth on a regular basis.
• Unplug the power plug and clean it with a dry cloth.
• Failure to do so may result in electric shock or re.
• Plug the power plug into the wall socket so that the cord is running towards the oor.
If you plug the power plug into the socket in the opposite direction, the electric wires
within the cable may be damaged and this may result in electric shock or re.
This appliance must be properly grounded.
Do not ground the appliance to a gas pipe, plastic water pipe, or telephone line.
• This may result in electric shock,re, an explosion, or problems with the product.
• Never plug the power cord into a socket that is not grounded correctly and make sure
that it is in accordance with local and national regulations.
Do not install this appliance near a heater or any inammable material.
Do not install this appliance in a humid, oily or dusty location, or in a location exposed to
direct sunlight or water (rain drops).
Do not install this appliance in a location exposed to low temperatures.
• Frost may cause the tubes to burst.
Do not use an electric transformer.
• This may result in electric shock or re.
Do not use a damaged power plug, damaged power cord, or loose wall socket.
• This may result in electric shock or re.
Do not pull or excessively bend the power cord.
Do not twist or tie the power cord.
Do not hook the power cord over a metal object, place a heavy object on the power cord,
Insert the power cord between objects, or push the power cord into the space behind the
appliance.
• This may result in electric shock or re.
WA7700J_WA10J7700GW-03520R-04_SA.indd 7 2016/5/12 11:20:21
8 English
Safety information
Safety information
Installation cautions
CAUTION
This appliance should be positioned in such a way that the power plug is easily accessible.
• Failure to do so may result in electric shock or re due to electric leakage.
Critical usage warnings
WARNING
If the appliance is ooded, turn off the water & power supplies immediately and contact your
nearest service centre.
• Do not touch the power plug with wet hands.
• Failure to do so may result in electric shock.
If the appliance generates a strange noise, a burning smell, or smoke, unplug the power plug
immediately and contact your nearest Samsung Customer Service.
• Failure to do so may result in electric shock or re.
In the event of a gas leak (such as propane gas, LP gas, etc.), ventilate immediately without
touching the power plug. Do not touch the appliance or power cord.
• Do not use a ventilating fan.
• A spark may result in an explosion or re.
Do not let children play in or on the washing machine. In addition, when disposing of the
appliance, remove the lid.
• If trapped inside the product, children may suffocate to death.
Do not wash items contaminated with gasoline, kerosene, benzene, paint thinner, alcohol or
other inammable or explosive substances.
• This may result in electric shock,re, or an explosion.
Do not touch the power plug with wet hands.
• This may result in electric shock.
Do not insert your hand or a metal object under the washing machine while an operation is
in progress.
• This may result in injury.
WA7700J_WA10J7700GW-03520R-04_SA.indd 8 2016/5/12 11:20:22
English 9
Safety information
Do not attempt to repair, disassemble, or modify the appliance yourself.
• Do not use a fuse (such as copper, steel wire, etc.) other than a standard fuse.
• When the appliance needs to be repaired or reinstalled, contact your nearest service
centre.
• Failure to do so may result in electric shock, re, problems with the product, or injury.
• In this case, the product will not be covered by the standard warranty provided by
Samsung and no responsibility can be attributed to Samsung for malfunctions or damages
resulting from doing it.
Unplug the power plug when the appliance is not being used for long periods of time or
during a thunder or lightning storm.
• Failure to do so may result in electric shock or re.
Do not put your hand into the spinning tub during the spin cycle.
• This may result in injury. If the tub does not stop spinning within 15 seconds after you
open the lid, contact your nearest Samsung Customer Service.
Usage cautions
CAUTION
When the washing machine is contaminated by a foreign substance such as detergent, dirt,
food waste, etc., unplug the power plug and clean the washing machine using a damp, soft
cloth.
• Failure to do so may result in discolouration, deformation, damage, or rust.
The product you have purchased is designed for domestic use only.
Using the product for business purposes qualies as a product misuse. In this case, the
product will not be covered by the standard warranty provided by Samsung and no
responsibility can be attributed to Samsung for malfunctions or damages resulting from such
misuse.
Do not stand on the appliance or place objects (such as laundry, lighted candles, lighted
cigarettes, dishes, chemicals, metal objects, etc.) on the appliance.
• This may result in electric shock,re, problems with the product, or injury.
Do not press the buttons using sharp objects such as pins, knifes, ngernails, etc.
• This may result in electric shock or injury.
WA7700J_WA10J7700GW-03520R-04_SA.indd 9 2016/5/12 11:20:22
10 English
Safety information
Safety information
Critical cleaning warnings
WARNING
Do not clean the appliance by spraying water directly onto it.
Do not use the strong acid cleaning agent.
Before cleaning or performing maintenance, unplug the appliance from the wall socket.
• Failure to do so may result in electric shock or re.
WA7700J_WA10J7700GW-03520R-04_SA.indd 10 2016/5/12 11:20:22
English 11
Installation
Installation
Follow these instructions carefully to ensure proper installation of the washer and to prevent
accidents when using it.
Unpacking your washer
Unpack your washer and inspect it for shipping damage. Make sure you have received all the
items shown below. If your washer was damaged during shipping, or you do not have all of
the items, contact 1300-362-603.
To prevent personal injury or strain, wear protective gloves whenever lifting or carrying the
unit.
WARNING
Packing materials can be dangerous to children; Keep all packing material (plastic bags,
polystyrene, etc.) well out of children’s reach.
CAUTION
When unpacking the washer, 2 person
collaboration is needed. To remove the
cushion bottom of the packing materials,
forward dumping is strictly prohibited.
WA7700J_WA10J7700GW-03520R-04_SA.indd 11 2016/5/12 11:20:22
12 English
Installation
Installation
Overview of your washer
Make sure all the parts are included in the product package. If you have a problem with
the washer or the parts, contact a local Samsung customer center or the retailer.
03
10
12
13
11
09
07
08
02
01
04
14
05
06
WA7700J_WA10J7700GW-03520R-04_SA.indd 12 2016/5/12 11:20:22
English 13
Installation
01 Drain hose Hose guide02 03 Lid
04 Built-in sink 05 Filter-rear Filter-front 06
07 08 Tub Water Jet Leveling feet09
10 Water hose (Cold) Water hose (Hot) Control panel11 12
13 Detergent drawer Power cord14
Parts supplied
Hose guide User manual Plastic zip hose tie Water intake cap
Water supply hoses
Tools needed for installation
Wrench Flat screwdriver Leveller
NOTE
• If you lose an accessory and want to purchase a replacement, contact the Samsung
service center 1300-362-603.
• The design of the parts and accessories may differ from the pictures above.
Their design is subject to change without notice for product improvement.
• Do not reuse old hoses. Only use new water supply hoses when you install the washer.
Old water supply hoses can leak or burst causing ooding and property damage.
• Conrm that there are rubber washers inside each coupling of the water supply hoses.
WA7700J_WA10J7700GW-03520R-04_SA.indd 13 2016/5/12 11:20:23
English 15
Installation
The water faucets must be within 4 feet
(122 cm) to the back of your Washer to
match the inlet hoses provided with your
Washer.
NOTE
Accessory inlet hoses are available in
various lengths up to 10 feet (275 cm) for
faucets that are further away from the back
of your washer.
To avoid the possibility of water damage:
• Have water faucets easily accessible.
• Turn off faucets when the washer is not
in use.
• Periodically check that there is no
leakage from the water inlet hose
ttings.
WARNING
Check all connections at the water valve and
faucet for leaks
Drain facility
The recommended height of the standpipe
is 39 in (99 cm). The drain hose must be
routed through the drain hose clip to the
standpipe. The standpipe must be large
enough to accept the outside diameter of
the drain hose. The drain hose is attached to
the washer at the factory.
Flooring
For best performance, you must install
your washer on a solidly constructed oor.
Woodoors may need to be reinforced to
minimize vibration and/or unbalanced load
situations. Carpeting and soft tile surfaces
are contributing factors to vibration which
can cause your washer to move slightly
during the spin cycle.
Never install your washer on a platform or
weakly supported structure.
Location considerations
Do not install your washer in areas where
water may freeze, since your washer will
always retain some water in its water valve,
pump, and hose areas. Frozen water can
damage the belts, the pump, hoses, and
other components.
Alcove or closet installation
Minimum clearances for closet and alcove
installations:
Sides 1 in /
25 mm
Closet
front
2 in /
51 mm
Rear 6 in /
152 mm Top 21 in /
533 mm
If the washer and dryer are installed
together, the closet front must have at least
a 72 in² (465 cm²) unobstructed air opening.
Your washer alone does not require a
specic air opening.
WA7700J_WA10J7700GW-03520R-04_SA.indd 15 2016/5/12 11:20:24
16 English
Installation
Installation
Recessed area
A
B B
A A
A1 in (2.5 cm)
B27.0 in (68.6 cm)
Side view - closet or conned area
A
B C D
E
A21 in (53.3 cm)
B2 in (5.1 cm)
C29.3 in (74.4 cm)
D6 in (15.2 cm)
E
Gap between end of water
valve and the wall
• Case 1. Assemble supply
hose after installing : Over
3.9 in (10 cm).
• Case 2. Assemble supply
hose before installing :
Over 2.8 in (7 cm).
WA7700J_WA10J7700GW-03520R-04_SA.indd 16 2016/5/12 11:20:24
English 17
Installation
Required dimensions for Installation
CB
A
A27.0 in (68.6 cm)
B39.2 in (99.5 cm)
C44.1 in (112.0 cm)
B
A
A29.3 in (74.4 cm)
B44.1 in (112.0 cm)
A
A59.8 in (152.0 cm)
B
A
C
C
A* 48.0 in2 (310.0 cm2
)
B* 24.0 in2 (155.0 cm2
)
C3.0 in (7.6 cm)
NOTE
* Required spacing
WA7700J_WA10J7700GW-03520R-04_SA.indd 17 2016/5/12 11:20:25
18 English
Installation
Installation
Important note to installer
Please read the following instructions carefully before installing your washer.
These instructions should be retained for future reference.
We recommend you hire a professional to install this washer.
Installation ow chart
Removing the
shipping bolts
(Front loading
washers only)
Connecting the
water and drain
Adjusting the
leveling feet
Selecting a
location
Powering your
washing machine
Running a test cycle
Run Rinse+Spin with
small amount of
laundry (about 4~5
towels) as a test cycle
Running
Calibration Mode
Finishing the
installation
Does your washer
vibrate?
NO
YES
Check again before steps.
Step-by-step installation
STEP 1 Selecting a location
NOTE
Before you install the washer, make sure the location:
• Has a hard, level surface without carpeting or ooring that may obstruct ventilation.
• Is away from direct sunlight.
• Has adequate ventilation.
• Is not exposed to freezing temperatures (temperatures under 32 °F or 0 °C).
• Is away from heat sources such as oil or gas.
• Has enough space so that the washer doesn’t rest on its power cord.
WA7700J_WA10J7700GW-03520R-04_SA.indd 18 2016/5/12 11:20:25
20 English
Installation
Installation
BA
1. Connect the ends of the water supply
hoses to the and hot (B) cold (A) faucets.
2. Tighten the ttings by hand until they
are snug, and then tighten them an
additional two-thirds of a turn with a
wrench.
CAUTION
When you fasten the ttings, do not fasten
them too tightly or apply tape or sealant to
the faucets or water supply intakes. This can
damage the ttings.
NOTE
After you have connected the water supply
hoses to the faucets, ensure that they are
connected correctly by pulling the water
supply hoses downwards.
3. Place the unconnected ends of the hoses
into a bucket and open the faucets
connected to the two water supply hoses
for 10 or 15 seconds to remove any
foreign substances from the hoses. Close
the faucets before continuing.
WA7700J_WA10J7700GW-03520R-04_SA.indd 20 2016/5/12 11:20:25
English 21
Installation
4. Connect the ends of the water supply
hoses to the water supply intake
connections at the back of the washer.
CAUTION
The water supply hose connected to the hot
faucet must be connected to the hot water
supply intake and the water hose connected
to the cold faucet must be connected to the
cold water supply intake.
5. Tighten the ttings by hand until they
are snug, and then tighten them an
additional two-thirds of a turn with a
wrench.
NOTE
To ensure the correct water usage, connect
both the hot and cold water faucets. If either
or both are not connected, an “4C” (noll)
code can be displayed.
NOTE
If you do not want to use the hot water
supply hose, insert the water intake cap
into the hot water supply intake hole. In
this case, you must select the Tap Cold
for the water temperature. If you select
the Tap Cold, all the lamps for the water
temperature options are turned off.
CAUTION
Conrm that the water supply hoses are not
twisted or bent. If the hoses are twisted or
bent, the hoses can leak and cause electric
shock due to the water leakage.
6. Turn on the hot and cold water supplies
and check all the water supply intake
connections and the faucets for water
leaks.
WA7700J_WA10J7700GW-03520R-04_SA.indd 21 2016/5/12 11:20:26
22 English
Installation
Installation
STEP 3 Connecting the drain hose
A
The end of the drain hose can be positioned
in three ways:
Over the edge of a wash basin
Secure the to the side of the hose guide (A)
basin wall with a hook or to the tap with
a piece of string to prevent the drain hose
from moving.
B C
*
D
E
In a standpipe or laundry tub
The standpipe (B) laundry tub (C) and must
be no shorter than 39 in (99 cm)* and no
longer than 96 in (245 cm)*.
NOTE
• Make sure that the connection between
the drain hose and the standpipe is not
airtight.
• D: Hose retainer, Tie strapE:
WA7700J_WA10J7700GW-03520R-04_SA.indd 22 2016/5/12 11:20:26
English 23
Installation
A
*
NOTE
Connect the within 4 in (10 hose guide (A)
cm)* from the end of the drain hose. If the
drain hose is extended more than 4 in (10
cm) beyond the end of the hose guide, mold
or microorganisms could spread to the
inside of the washer.
NOTE
The drain hose can be installed to a 96
in (245 cm) maximum, but the draining
capability can be reduced at this height.
It can cause the washer to have an odor
because of remaining water in the drain
system.
NOTE
If the drain hose is installed below 39 in (99
cm), water can be drained in cycles due to a
siphon phenomenon. It causes the washer to
display “4C.
STEP 4 Leveling your washer
A
See if the washer is level by checking the
position of the tub:
1. Slide the washer into position.
2. Open the lid of the washer, and pour
the water into the tub to just below the
pulsator level.
WA7700J_WA10J7700GW-03520R-04_SA.indd 23 2016/5/12 11:20:27
24 English
Installation
Installation
B C
3. If the washer is level, the is pulsator (A)
positioned at the center of the water as
shown in the gure.
If not, level your washer by turning
the front leveling feet clockwise or
counterclockwise as necessary.
NOTE
Turn the front leveling feet clockwise (B) to
lower the washer, and counterclockwise (C)
to raise the washer.
STEP 5 Powering your washer
Plug the power cord into a 3-prong, well
grounded 220-240 volt 50 Hz approved
electrical outlet protected by a fuse or
comparable circuit breaker.
Your washer is grounded through the third
prong of the power cord when plugged into
a three-prong grounded electrical outlet.
Test run
Make sure that you install your washer
correctly by running the after Rinse+Spin
the installation is complete.
WA7700J_WA10J7700GW-03520R-04_SA.indd 24 2016/5/12 11:20:27
English 25
Installation
STEP 6 Running a test cycle
Run a test cycle as follows to check if your washer is properly installed.
1. Load about 6 pounds of laundry into the tub.
2. Press Power to turn on your washer.
3. Select Rinse+Spin by turning the Cycle Selector.
4. Press Start/Pause to start the test cycle.
5. The washer should not rock or vibrate excessively when water is supplied or when
washing or spinning, and should drain well during the spin cycle.
NOTE
If water leaks while water is being supplied or drained, check the water connections. Refer to
the “STEP 2 Connecting the water supply hose” section on page 19 for instructions.
NOTE
If the washer rocks and vibrates excessively, level your washer again. Refer to the STEP
4 Leveling your washer” section on page 23 for instructions.
STEP 7 Calibration Mode
Your Samsung washer detects the laundry weight automatically.
For more accurate weight detection, please run Calibration Mode after the installation.
To run Calibration Mode, follow these steps:
1. Remove laundry or any contents in the machine.
2. Press and hold Water Level Delay End and simultaneously for at least 3 seconds when
the power is turned on.
3. Press Start/Pause to activate Calibration Mode.
4. The pulsator rotates clockwise and counterclockwise approximately 1 minute.
5. When Calibration Mode is nished, “End” appears on the display, and the washer
automatically turns off. The washer is now ready for use.
WA7700J_WA10J7700GW-03520R-04_SA.indd 25 2016/5/12 11:20:27
26 English
Operating instructions
Operating instructions
WARNING
To reduce the risk of re, electric shock, or injury to persons when using your appliance,
follow basic precautions, including the following:
Loading your washer
• Fill the tub with dry, unfolded clothes
evenly around in order to enhance
washing efciency and prevent excess
wear, or wrinkling of the load.
• For optimal washing performance, make
sure the laundry is piled up evenly.
• Wash delicate items such as bras, hosiery,
and other lingerie in the Delicates cycle
with similar lightweight items.
• When washing big bulky items or a
few smaller items that don’t ll the tub
completely – a rug, a pillow, stuffed toys,
or one or two sweaters, for example – add
a few towels to improve spin performance.
• Do not insert bulky items except for
Bedding in this cycle.
NOTE
During the spin cycle, the washer may add
additional water to redistribute the clothes
and correct an imbalance inside the drum.
• When washing heavily soiled loads, do
not overload your washer to ensure good
cleaning results.
CAUTION
• Inatable items may cause damage to the
laundry or the machine during the wash or
drying process.
• Regardless of the size, blankets or quilts
are safer and cleaner to wash one item at
a time. Two different-sized blankets in the
same load may compromise the drying
performance due to unbalanced loads.
WA7700J_WA10J7700GW-03520R-04_SA.indd 26 2016/5/12 11:20:28
English 27
Operating instructions
To input a blanket
Fold the blanket into the blanket-specic net
as shown, and then insert in the tub below the
plastic area of the tub.
CAUTION
Make sure the laundry is inserted completely.
• Any exposed part of the laundry may
cause damage to the machine or the
laundry itself, or a water leak.
• Do not overload the tub. Make sure no
part of the laundry is exposed outside of
the tub.
To add a forgotten item:
1. Press Start/Pause to pause the washer.
2. Wait for the door to unlock automatically, and then open the door.
3. Add the item, close the door, and then press Start/Pause. The cycle will resume.
Getting started
1. Load your washer.
2. Add liquid (or powder) detergent and additives to the dispenser (see the "Detergent use"
section on page 37).
3. Select the appropriate cycle and options for the load (see the "Washing a load of laundry"
section page 28).
4. Close the lid.
5. Press Start/Pause.
6. The Wash Indicator illuminates.
7. The estimated cycle time will appear in the display.
The time may uctuate to indicate the time remaining in the cycle.
NOTE
The actual time required for a cycle may differ from the estimated time in the display
depending on the water pressure, water temperature, detergent, and laundry.
8. Before your washer starts to ll, it will make a series of clicking noises to check the door
lock and do a quick drain.
NOTE
• When the cycle is complete, the indicator will go out and ” will appear Door Lock End
in the display.
• Pressing Power cancels the cycle and stops your washer.
• The Wash Rinse Spin, , and indicators will illuminate during those portions of the cycle.
WA7700J_WA10J7700GW-03520R-04_SA.indd 27 2016/5/12 11:20:28
28 English
Washing a load of laundry
Washing a load of laundry
WARNING
To reduce the risk ofre, electric shock, or injury to persons, read the IMPORTANT SAFETY
INSTRUCTIONS before operating this appliance.
Control panel
01
02
03 04 05
06
07
08
09
10
11
01 Cycle Selector Turn the Cycle Selector to select the desired cycle. The indicator by
the cycle name lights up.
02 Display Provides instructions and diagnostics while keeping you updated on
the cycle status and time remaining.
03 Water Level
The water level is automatically adjusted. However, you can select the
water level manually by pressing this button.
According to the texture and humidity of clothes, water level and
water consumption may differ.
04 Temp.
Press the button repeatedly to cycle through the different water
temperature options.
• Hot - Whites and heavily soiled, colorfast items.
• Warm - Colorfast items.
• Cold - Brightly colored, very lightly soiled items.
05 Activ Dual
Wash
This button provides two options, and is available only when the
washing machine is stopped or in Standby state.
• Water Save (default): Reuse water in the tub that remains
after using Water Jet. The water will be used for the main cycle.
• Drain: Select to drain water that remains after using Water Jet.
When draining is complete, the washing machine switches to
Water Save mode automatically. Then, you can choose a cycle.
WA7700J_WA10J7700GW-03520R-04_SA.indd 28 2016/5/12 11:20:28
English 29
Washing a load of laundry
06 Delay End Delay the end of any cycle for up to 19 hours in one-hour increments.
Displayed hour indicates the time the wash will be ended.
07 Wash Press this button to only perform a wash cycle or to adjust the wash
time.
08 Rinse Press this button to only perform a rinse cycle or to adjust the rinse
count.
09 Spin
Press this button to perform a spin cycle only or to adjust the spin
time.
You can set the spin time from between 1 to 9 minutes. (except for
WATER SAVING )
When only a spin is selected, the spin time will be different from the
total remaining time. This is because the total remaining time includes
the actual spin time and the times for water draining and stopping.
10 Power
Press once to turn your washer on. Press again to turn your washer
off. If the washer is left on for more than 10 minutes without any
buttons being pressed, the power automatically turns off.
11 Start/Pause Press to pause and restart cycles.
Cycle overview
Cycle Description
COTTON
Suitable for a averagely soiled cotton load.
For cottons, bed linens, table linens, underwear, towels, or shirts.
The washing time and the number of rinse cycles are
automatically adjusted according to the load.
LAST SETTING
Selects this cycle to load the settings for the last cycle.
Perform a wash cycle using the last used settings without having
to enter them manually again. Your choices are automatically
saved when you press the Start/Pause button. To use a
memorized cycle, press the Last Setting button and then press
the Start/Pause button.
DELICATES
This cycle is for washing delicate clothes that are easily deformed
or damaged and woollen sweaters and cardigans with a water
wash sign.
WA7700J_WA10J7700GW-03520R-04_SA.indd 29 2016/5/12 11:20:28
30 English
Washing a load of laundry
Washing a load of laundry
Cycle Description
HEAVY DUTY For sturdy, colorfast fabrics and heavily soiled garments.
WATER SAVING
This is a specially designed cycle that enables you to wash
laundry effectively with the minimum amount of water.
Water saving, water level 7, water supply Warm, Wash 1:50,
Rinse 3, Spin 12 is the test programme used for energy labeling
in accordance with AS/NZS 2040.
Suitable for a normally soiled cotton load.
BEDDING
For bulky and large items, such as comforters, blankets and
sheets. When washing comforters, use liquid detergent.
Do not wash waterproof or water-resistant items such as
mattress covers, bath mats and plastic mats which hardly
absorb water.
QUICK WASH For lightly soiled garments needed quickly.
40 MAGIC CLEAN This cycle effectively removes dirt using a customized water
temperature.
60 MAGIC CLEAN This cycle effectively removes dirt using a customized water
temperature.
RINSE + SPIN Use for loads that need rinsing only or to add rinse-added
fabric softener to a load.
TUB CLEAN Use this program to clean the tub. It will keep the tub clean and
sanitary.
Options
Child Lock
Child Lock prevents children from playing
with your washer.
Activating the Child Lock function
Press and hold Temp. and Activ Dual Wash
simultaneously for approximately 3 seconds.
• When you activate the Child Lock
function, the Child Lock indicator
blinks.
Using the Child Lock function
If the lid is opened when the Child Lock
function is on, ” is displayed and an dC
alarm sounds.
• If the water level in the tub is above the
safe water level, “ ” is displayed on the dC
LED display and the washer starts to
drain water by force after 30 seconds.
The Power button is disabled while the
washing machine drains water in Child
Lock mode.
WA7700J_WA10J7700GW-03520R-04_SA.indd 30 2016/5/12 11:20:29
32 English
Washing a load of laundry
Washing a load of laundry
Garment Plus
You can add or take out laundry items even
after the wash has started, as long as the
Garment Plus indicator is on. Pressing
Start/Pause unlocks the lid. If you open the
lid and want to continue the wash cycle,
close the lid, and then press Start/Pause.
Delay End
You can set the washer to start your wash
automatically at a later time, by choosing a
delay time.
The hour displayed indicates the time at
which the wash will be ended.
1. Set your wash cycle.
2. Press Delay End repeatedly until the
delay time is set.
3. Press Start/Pause. The “Delay End”
indicator will be lit, and the clock will
begin counting down until it reaches the
set time.
4. To cancel a Delay End function, press the
Power button and then turn the washer
on again.
Mist Shower
Mist Shower sprays water from a nozzle
that is independent of the main water
supply system. It states that is soaks the
laundry with water from the beginning of
the rinse cycle and ensures an effective
wash, but it’s not part of the wash cycle, it’s
part of the rinse cycle, so this needs to state
that it ensures an effective rinse.
(The Mist Shower function may not work if
there is too large of a load in the machine.)
Smart Check
This function enables you to check the
status of the washer using a smartphone.
1. To enable the Smart Check function,
press and hold Activ Dual Wash Spinand
for 3 seconds after turning the power on
or when an error occurs.
NOTE
The error code history is deleted after you
use this function.
2. The Smart Check indicator is lit on the
display.
3. Run the Smart Check app on your smart
phone.
Android: Galaxy S series, Galaxy
Note series. (Other devices may not
be normal operation).
Supported OS : Android 2.2 or higher
iOS: iPhone series
Supported OS : iOS 4.3 or higher
4. Focus your smart phone’s camera on the
display panel of the washer.
5. If the smart phone’s camera is focused
on the display panel of the washer, the
panel and error message is automatically
recognized and the error type and
countermeasures are displayed on the
smart phone.
6. If the smartphone fails to recognize the
error code more than twice, please enter
the error code displayed on the display
panel of the washer manually into the
Smart Check app.
NOTE
Downloading the Smart Check app
• Download the Samsung Laundry App
into your mobile phone from the
Android market or Apple App store.
(Search word : Samsung Smart Washer/
Dryer)
WA7700J_WA10J7700GW-03520R-04_SA.indd 32 2016/5/12 11:20:29
English 33
Washing a load of laundry
NOTE
Precautions when using Smart Check
• If light from a light bulb, uorescent
bulb, or lamp is reected on the display
panel of the washer, the smartphone
may not be able to recognize the panel
or error message easily.
• If you hold the smartphone at too
large an angle relative to the front of
the display panel, it may not be able
to recognize the error code. For best
results, hold the smartphone so that the
front of the panel and the smartphone
are parallel or nearly parallel.
Washing clothes using the cycle selector
Your new washer makes washing clothes
easy, using Samsung’s “Fuzzy Control
automatic control system. When you select
a wash program, the machine will set the
correct temperature, washing time, and
washing speed.
1. Press Power.
2. Open the lid.
3. Load the articles of clothing one at a
time loosely into the drum, without
overlling it.
4. Add liquid (or powder) detergent,
softener, and/or bleach (if necessary) to
the appropriate compartments. See the
"Detergent use" section on page 37.
5. Close the lid.
6. Use the Cycle Selector to select the
appropriate cycle according to the type
of material: COTTON, LAST SETTING,
DELICATES, HEAVY DUTY, WATER
SAVING BEDDING, , QUICK WASH, 40
MAGIC CLEAN, 60 MAGIC CLEAN,
RINSE+SPIN and . The TUB CLEAN
relevant indicators will illuminate on the
control panel.
7. At this time, you can control the wash
temperature, the number of rinse cycles,
the spinning time, and the delay time by
pressing the appropriate option button.
8. Press Start/Pause and the wash will
begin. The process indicator will light up
and the remaining time for the cycle will
appear in the display.
Pause Option
To remove or add laundry items, follow
these steps:
1. Press Start/Pause to unlock the lid.
NOTE
The lid cannot be opened when the water is
too HOT.
2. Remove or add laundry items.
3. Close the lid, and then press Start/Pause
to restart the wash.
NOTE
If you have Child Lock on, you must
deactivate it rst. See page 30-31.
WA7700J_WA10J7700GW-03520R-04_SA.indd 33 2016/5/12 11:20:29
34 English
Washing a load of laundry
Washing a load of laundry
When the cycle is nished:
After the total cycle has nished, the power
will turn off automatically.
1. Open the lid.
2. Remove laundry.
ATC (Auto Temperature Control)
ATC is the control function that the
washer controls water temperature with
temperature sensor (thermistor).
NOTE
Because there are numerous water
temperatures depending on the customer’s
environments (cold areas, warm areas,
various water temperatures, settings of
heater temperature, etc.), ATC function in our
washer maintains the certain level of wash
temperature to output the best washing
performance at each cycle.
NOTE
If you select , this cycle is the NORMAL
regulation and UL cycle. Since new washers
must reduce the amount of energy usage as
a rst priority, customers will notice more
cold water entering the washer. But, this is
normal, not a problem.
In those regulation cycles, Hot temperature
is similar to acceptable adult bath-water
temperature and warm temperature is
similar to comfortable swimming-pool water
temperature.
NOTE
If customers want to wash clothes in specic
water temperatures, customers should
choose a different cycle at each temperature
(Hot/Warm).
WA7700J_WA10J7700GW-03520R-04_SA.indd 34 2016/5/12 11:20:30
English 35
Washing a load of laundry
The basics
Prewash (Water Jet & Built-in sink)
Water Jet and Built-in sink help you
handwash before the washing machine
starts operation. Water Jet is available only
when the door is open with the water level
set to less than High. For prewashing, use
the Built-in sink that is designed to facilitate
the hand-wash.
1. With the door open, lower the Built-in
sink . To open only the door, press and
release the front right corner of the
door. To close and lock both the door
and the Built-in sink, press down the
door until you hear a clicking sound.
2. Put clothes to prewash in it.
3. Press Water Jet to supply water to the
Built-in sink, and hand-wash.
4. When done, gently lift up the Built-in
sink to drain water into the tub.
NOTE
• If you want to hand-wash while the
machine is operating, press Start/Pause
to stop operation, and then follow steps
1-4 above.
• If you open both the door and the
Builtin sink, lower the Built-in sink
manually for prewashing.
[Water Jet stops]
• Water Jet stops operation automatically
when the washing machine detects the
maximum water level.
• Water Jet stops operation automatically
5 minutes after it begins. To add more
water, press Water Jet again to resupply
water.
WA7700J_WA10J7700GW-03520R-04_SA.indd 35 2016/5/12 11:20:30
36 English
Washing a load of laundry
Washing a load of laundry
[Water Jet drains]
• Select a cycle and press Start/Pause. Then
the washing machine drains the water to be
used during the prewash.
• When the washing machine is turned off
before starting the wash cycle, it drains
the water to be used during the prewash.
However, when it is turned off during the
wash cycle, it does not drain the water.
NOTE
• Water Jet extracts the water through the
Mist Shower nozzle for 1 second and then
through the Water Jet nozzle from then on
when it is rst activated after the washing
machine turns on.
CAUTION
• Do not abuse Water Jet. Excessive use of
Water Jet increases water consumption.
• When running water to the tub, do that
gently. Otherwise, water may overow the
tub.
• Use caution when removing laundry from
the tub. You may bump your head on the
Built-in sink.
• Do not block the outlet of Water Jet with
hands. Water may leak outside the tub,
causing a system failure.
• Put only clothes to prewash in the Built-in
sink. Other items such as shoes, food, or
animals can not be used for prewash.
• Do not open the Built-in sink in a hurry.
Remaining water in the sink may splash on
the door or control panel.
• Due to a difference in air pressure, Water Jet
may splash water from its outlet when it is
rst activated.
• This lid must be closed tightly to do the
laundry.
WA7700J_WA10J7700GW-03520R-04_SA.indd 36 2016/5/12 11:20:30
English 37
Washing a load of laundry
Detergent use
• The use a good quality top loader
detergent is recommended.
• It is also important to:
Pretreat stains before washing.
Sort clothes by color.
Sort clothes by the amount of soiling.
Avoid overloading.
NOTE
• When using powdered detergent it
is recommended that the powder be
dissolved in warm water to ensure
optimum cleaning results.
• The detergent/water mixture can
be added to either the tub or to the
detergent dispenser tray.
• Reducing the amount of detergent used
may reduce the effectiveness of the
cleaning action.
WA7700J_WA10J7700GW-03520R-04_SA.indd 37 2016/5/12 11:20:30
38 English
Washing a load of laundry
Washing a load of laundry
Features
Automatic dispenser
Your washer has separate compartments for dispensing detergent and color-safe bleach and
fabric softener. Add all laundry additives to their respective compartments before starting
your washer.
The automatic dispenser must always be in place before you start your washer.
DO NOT open the automatic dispenser when your washer is running.
NOTE
• Never exceed the manufacturer’s recommendations when adding detergent.
• This compartment holds liquid detergent for the main wash cycle, which is added to the
load at the beginning of the cycle.
• When using powdered detergent, remove the liquid detergent compartment from the
detergent drawer. The washer will not dispense powdered detergent from the liquid
detergent compartment.
To add detergent to the automatic dispenser:
1. Open the dispenser drawer.
2. Load the recommended amount of liquid
(or powder) detergent into the detergent
compartment before you start your
wash.
3. Close the drawer slowly and smoothly
to avoid spilling, splashing, or premature
dispensing of the contents.
NOTE
It is normal for a small amount of water to
remain in the dispenser compartments at
the end of the cycle.
NOTE
Do not put chlorine bleach in the dispenser
drawer.
WA7700J_WA10J7700GW-03520R-04_SA.indd 38 2016/5/12 11:20:31


Specyfikacje produktu

Marka: Samsung
Kategoria: pralka
Model: WA10J7700GW

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Samsung WA10J7700GW, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje pralka Samsung

Instrukcje pralka

Najnowsze instrukcje dla pralka