Instrukcja obsługi Roland PDA120


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Roland PDA120 (2 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 37 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/2
Before using this unit, carefully read the leaet “USING THE UNIT SAFELY” and “IMPORTANT NOTES. After reading, keep the
document(s) where it will be available for immediate reference.
© 2020 Roland Corporation
Names of Parts
Output jack
Hoop rubber Head
Tuning bolt
Shell
Lug
Hoop
(rim)
Hand knob
Bottom head
Bracket
* The illustration shows the PDA100.
PDA140F only
Legs
NOTE
Due to the characteristics of the materials used in the sensor, the
strike feel of the head and the sensitivity of the sensor may be
aected by changes in temperature and humidity.
Mounting on a Stand
PDA120, PDA100 only
Tom holder
Loosen
Allowable diameter of mounting rod: 9–13 mm (3/8–9/16 inches)
Connecting to the Drum Sound Module
Using the included connection cable (stereo cable) or the
dedicated connection cable included with your drum sound
module, attach the pad to your drum sound module.
Connect the L-shaped plug of the connection cable to the pad’s
output jack.
Using a mono cable will NOT allow rim shots.
* To prevent malfunction and equipment failure, always turn
down the volume, and turn o all the units before making any
connections.
L-shaped
plug
I-shaped
plug
To Output jack
Example: Drum Sound Module TD-27
Connection cable
(Accessory)
Recommended Parameter Settings
These are the recommended setting values for the trigger
parameters when using the PDA140F, PDA120, or PDA100 with
your drum sound module.
Choose these if “PDA140F/PDA120/PDA100” is one of the choices
for “PAD TYPE” or “TRIG TYPE” on your drum sound module.
If “PDA140F/PDA120/PDA100” is not one of the choices, then
refer to the support information on the Roland website.
http://roland.cm/trigger_prm
You might need to adjust the trigger parameters depending
on the conditions of use, such as the mounting method or the
position of the PDA140F, PDA120, or PDA100.
For details on these settings, refer to the owner’s manual of your
drum sound module.
Adjusting the Head Tension
Before playing, you must adjust the pad tension rst.
If the head is too loose, the sensor might not work correctly,
or the sensor might be damaged. For stable operation, adjust
the head tension slightly tighter than the strike feel of a typical
acoustic drum.
NOTE
To avoid faulty operation, observe the following points.
5Adjust the head evenly so that it does not sag.
5Adjust the tuning bolts so that they are not loose.
5It is not
necessary to adjust the tension of the bottom head.
1. Adjust each tuning bolt little by little, across the head
as indicated in the illustration.
Head
Tuning bolt
21
53
46
NOTE
Fully tightening a tuning bolt at only a single location produces
uneven tensioning, and correct playing dynamics may not
be achieved or may even cause malfunctions. Even tuning/
tensioning is very important.
2. Adjust the tightness of each tuning bolt so that the
head is tensioned evenly.
MEMO
5Head tension will not aect the actual tuning of the sound you
are playing. For that you need to adjust sound parameters in
the drum sound module you are using. For details, refer to the
owners manual of your drum sound module.
5Also, head tension may change depending on usage. Adjust
as needed.
Replacing the Head or Hoop Rubber
The performance of the head and/or hoop rubber will diminish
with use over time. If the head is torn or becomes too fatigued, or
impossible to tension correctly, then it should be replaced. If the
hoop rubber is worn out, it too can be replaced.
For replacement heads or to have the hoop rubber replaced,
please contact your dealer or a Roland service center.
Replacing the Head
NOTE
5Applying excessive force to the sensors located under the
head can damage them and/or interfere with accurate
triggering.
5It is not necessary to replace the bottom head.
PDA140F, PDA120
Head
Hoop
Sensors
* The illustration shows the PDA120.
PDA100
Sensor
1. Remove all tuning bolts.
Go around and loosen each bolt a little at a time by turning it
counter-clockwise.
2. Remove the hoop and old head.
* Take care not to touch the sensor with your hand.
3. Place the new head and hoop on the shell.
4. Install all six tuning bolts.
5. Adjust the tension of the head.
Playing Methods
Head shot
Hit only the head of the pad.
MEMO
For details on the sounds that are
supported, refer to the owners
manual of your drum sound
module.
Rim shot
Strike the head and the rim of
the pad simultaneously.
A sound (rim sound) dierent
than the head shot will be
heard.
Head shot
Rim shot
Head shot
Main Specications
Roland PDA140F, PDA120, PDA100: V-Pad
PDA140F PDA120 PDA100
Shell 14 (diameter) x 14 (depth) inches
Wood shell
12 (diameter) x 8 (depth) inches
Wood shell
10 (diameter) x 7 (depth) inches
Wood shell
Head
Top: 3-ply mesh head
(middle level oating structure)
Bottom: 3-ply mesh head
Top: 2-ply mesh head
Bottom: 2-ply mesh head
Triggers 2 (Head, Rim)
Connector Output jack
Allowable diameter of
mounting rod 9–13 mm (3/8–9/16 inches)
Dimensions
415 (W) x 430 (D) x 385 (H) mm
16-3/8 (W) x 16-15/16 (D) x 15-3/16 (H)
inches
(excluding legs)
345 (W) x 380 (D) x 227 (H) mm
13-5/8 (W) x 15 (D) x 8-15/16 (H) inches
295 (W) x 330 (D) x 210 (H) mm
11-5/8 (W) x 13 (D) x 8-5/16 (H) inches
Weight 6.4 kg/14 lbs 2 oz (including legs)
5.3 kg/11 lbs 11 oz (excluding legs)
3.4 kg
7 lbs 8 oz
2.9 kg
6 lbs 7 oz
Accessories Owners Manual, Leaet “USING THE UNIT SAFELY, Connection cable, Drum key
This document explains the specications of the product at the time that the document was issued. For the latest information, refer to
the Roland website.
Owner’s Manual
PDA140F PDA120 PDA100 V-Pad English
When you need repair service, access this URL and nd your nearest
Roland Service Center or authorized Roland distributor in your country.
http://roland.cm/service
Roland Service Centers and Distributors
About the natural markings on this product
The shells used on this product are manufactured to
accentuate their natural feel and texture.
For this reason, each drum and its parts feature slightly
dierent colorations and woodgrains (natural markings).
This shows that the product is made from real wood, and
does not indicate any problems with quality.
Precautions regarding placement of this unit on a stand
Be sure to follow the instructions in the Owner’s Manual carefully when placing
this unit on a stand.
If it is not set up properly, you risk creating an unstable situation which could
lead to the unit falling or the stand toppling, and may result in injury.


Specyfikacje produktu

Marka: Roland
Kategoria: nieskategoryzowany
Model: PDA120

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Roland PDA120, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje nieskategoryzowany Roland

Roland

Roland GK-KIT-BG Instrukcja

12 Września 2024
Roland

Roland MVS-12 Instrukcja

12 Września 2024
Roland

Roland V-800HD Instrukcja

12 Września 2024
Roland

Roland XI-DANTE Instrukcja

12 Września 2024
Roland

Roland XI-REAC Instrukcja

12 Września 2024
Roland

Roland S-4000M Instrukcja

12 Września 2024
Roland

Roland CB-37SY Instrukcja

12 Września 2024
Roland

Roland SO-AES4 Instrukcja

12 Września 2024
Roland

Roland TD-12K Instrukcja

12 Września 2024
Roland

Roland CB-CS2 Instrukcja

12 Września 2024

Instrukcje nieskategoryzowany

Najnowsze instrukcje dla nieskategoryzowany

Meec Tools

Meec Tools 010-084 Instrukcja

6 Października 2024
Outwell

Outwell Scenic Road 250 Instrukcja

5 Października 2024
Impact

Impact QuikBalance Instrukcja

4 Października 2024
Impact

Impact CA-112 Instrukcja

4 Października 2024
Impact

Impact LS-BHA Instrukcja

4 Października 2024
Impact

Impact LKB-5C Instrukcja

4 Października 2024
Impact

Impact RST-001 Instrukcja

4 Października 2024