Instrukcja obsługi Roland MDS-20BK

Roland Niesklasyfikowane MDS-20BK

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Roland MDS-20BK (4 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/4
08240-8000 3UL
Owner´s Manual
Thank you for purchasing the Roland Drum Stand MDS-20.
201a
Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT
NOTES.” These sections provide important information concerning the proper operation of the unit.
Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new
unit, Owner’s manual should be read in its entirety. The manual should be saved and kept on hand as a conve-
nient reference.
1.
Loosen the two HAND KNOBs marked “a,” and open
the stand in order as Left side –> Right Side.
2.
Loosen the four QUICK RELEASE CAM LEVERs
marked “b,” and adjust height of the stand.
3.
Loosen the two QUICK RELEASE CAM LEVERs
marked “c,” and mount the two CYMBAL ARMs
marked “d” on the stand.
4.
Mount the four PAD MOUNTs marked “e” on the
stand.
5.
Mount the one CYMBAL MOUNT marked “f” on the
stand.
* Regarding the way of mounting a Sound Module or a Pad, please refer
to the Owner’s Manual that is installed in the products.
How to set up the Stand
bb
e
e
bb
aa
c
d
e
c
d
f
* If the drum stand is to be used for extended periods in the same location,
we recommend using a Roland drum mat (TDM-10/TDM-20) to prevent
discoloration of flooring by the rubber feet.
A
CB
When you adjust the screws on the joint
parts by yourself, please tighten them in
order of the embossed → →
to make sure of the gripping.
A B C
202
Copyright © 2004 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced
in any form without the written permission of ROLAND CORPORATION.
• Do NOT open the legs of the stand at more than 135 degrees, and NOT make
the distance of both Right/Left end legs as more than 2 m (80 inches). If you
do so, the cable (inside the Pipes) could get damaged and/or the stand could
fall down.
• Do NOT loosen the other screw than Hand Knob and Quick Release Cam
Lever.
• Do NOT pull the cables tensely too much.
1.
Insert the PLUG of connecting cables into the TRIGGER INPUT JACK on backside of the
sound module.
2.
Insert the other (opposite side) PLUG into the TRIGGER OUTPUT JACK of each pad.
* When you connect the cables, please refer to the marking label that is attached on both edge of the cables.
Four more pads can be added using the four auxiliary cables marked “AX1–AX4.”
• Accessories
• Required Space for Set-up
1,400 (L) x 950 (W) x 1,100 (H) mm
55-1/8 (L) x 37-7/16 (W) x 43-5/16 (H) inches
1,700 (L) x 1,400 (W) x 1,250 (H) mm
66-15/16 (L) x 55-1/8 (W) x 49-1/4 (H) inches (including Sound Module, Kick Trigger, Cymbal, and Stool)
• Tube Diameter
38.1 mm 1-1/2 inches (Horizontal Tube)
41.3 mm 1-5/8 inches (Vertical Tube)
• Weight 18.3 kg / 40 lbs 6 oz
962a
* In the interest of product improvement, the specifications and/or appearance of this unit are subject to change without prior notice.
Caution in setting up the Stand
How to connect the cables
Specifications
• Drum Key • Cable Tie (8 pieces) • Cable Marking Label Sheet
• Owner’s Manual
2 m (80 inches)
135˚
135˚
AX4 AX3 AX2 AX1 RDE RD CR2 CR1 T4 T3 T2 T1 SNR KIKHHC HH
SNR
001
• Before using this unit, make sure to read the instructions
below, and the Owner’s Manual.
..........................................................................................................................
002b
• Do not open or perform any internal modifications on the
unit (except for adjusting the pad mount or cymbal arm).
..........................................................................................................................
003
• Do not attempt to repair the unit, or replace parts within
it (except when this manual provides specific instructions
directing you to do so). Refer all servicing to your retailer,
the nearest Roland Service Center, or an authorized
Roland distributor, as listed on the “Information” page.
..........................................................................................................................
004
• Never use or store the unit in places that are:
• Subject to temperature extremes (e.g., direct sunlight in
an enclosed vehicle, near a heating duct, on top of heat-
generating equipment); or are
• Damp (e.g., baths, washrooms, on wet floors); or are
• Humid; or are
• Exposed to rain; or are
• Dusty; or are
• Subject to high levels of vibration.
..........................................................................................................................
007
• Make sure you always have the unit placed so it is level
and sure to remain stable. Never place it on stands that
could wobble, or on inclined surfaces.
..........................................................................................................................
013
• In households with small children, an adult should
provide supervision until the child is capable of
following all the rules essential for the safe operation of
the unit.
..........................................................................................................................
add
• To prevent accidents, never allow small children to play
near the stand.
..........................................................................................................................
104
• Try to prevent cords and cables from becoming
entangled. Also, all cords and cables should be
placed so they are out of the reach of children.
..........................................................................................................................
106
• Never climb on top of, nor place heavy objects on the unit.
..........................................................................................................................
115b
• Install only the accessories or parts into the unit that are
recommended by Roland. Remove only the specified
screws during the installation.
..........................................................................................................................
118
• Should you remove the bolts and washers, make sure to
put them in a safe place out of children's reach, so there is
no chance of them being swallowed accidentally.
..........................................................................................................................
add
• Make sure to firmly tighten all clamps and bolts after you
have assembled the stand and attached any components.
You should probably also try to make a habit of checking
and retightening them if necessary before every perfor-
mance. You risk injury if you have loose screws or
clamps, since a pad or component can fall unexpectedly.
..........................................................................................................................
add
• When setting up or storing the stand, be careful not to
pinch your hands or fingers in the stand joints.
..........................................................................................................................
IMPORTANT NOTES
291a
In addition to the items listed under “USING THE UNIT SAFELY” on
this page, please read and observe the following:
Placement
354a
• Do not expose the unit to direct sunlight, place it near devices that
radiate heat, leave it inside an enclosed vehicle, or otherwise
subject it to temperature extremes. Excessive heat can deform or
discolor the unit.
• Depending on the conditions of the setup location (flooring
materials, temperature, etc.), the drum stand’s rubber feet may
cause discoloration or marring of the floor surfaces.
Laying felt or other soft cloth under the rubber feet may allow you
to use the stand without such concerns. However, when employing
such methods, you need to make sure that the stand cannot slip
and move around.
Maintenance
401a
•
For everyday cleaning wipe the unit with a soft, dry cloth or one that
has been slightly dampened with water. To remove stubborn dirt,
use a cloth impregnated with a mild, non-abrasive detergent. After-
wards, be sure to wipe the unit thoroughly with a soft, dry cloth.
402
• Never use benzine, thinners, alcohol or solvents of any kind, to
avoid the possibility of discoloration and/or deformation.
Additional Precautions
556
• When connecting / disconnecting all cables, grasp the connector
itself—never pull on the cable. This way you will avoid causing
shorts, or damage to the cable’s internal elements.
Used for instructions intended to alert
the user to the risk of injury or material
damage should the unit be used
improperly.
* Material damage refers to damage or
other adverse effects caused with
respect to the home and all its
furnishings, as well to domestic
animals or pets.
Used for instructions intended to alert
the user to the risk of death or severe
injury should the unit be used
improperly.
The ● symbol alerts the user to things that must be
carried out. The specific thing that must be done is
indicated by the design contained within the circle. In
the case of the symbol at left, it means that the power-
cord plug must be unplugged from the outlet.
The symbol alerts the user to important instructions
or warnings.The specific meaning of the symbol is
determined by the design contained within the
triangle. In the case of the symbol at left, it is used for
general cautions, warnings, or alerts to danger.
The symbol alerts the user to items that must never
be carried out (are forbidden). The specific thing that
must not be done is indicated by the design contained
within the circle. In the case of the symbol at left, it
means that the unit must never be disassembled.

Specyfikacje produktu

Marka: Roland
Kategoria: Niesklasyfikowane
Model: MDS-20BK

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Roland MDS-20BK, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Roland

Roland

Roland KS-V7 Instrukcja

29 Grudnia 2024
Roland

Roland CYQ-12 Instrukcja

21 Grudnia 2024
Roland

Roland PDQ-8S Instrukcja

21 Grudnia 2024
Roland

Roland PD-14DSX Instrukcja

10 Grudnia 2024
Roland

Roland V71 Editor Instrukcja

10 Grudnia 2024
Roland

Roland KD-22 Instrukcja

10 Grudnia 2024
Roland

Roland Bridge Cast One Instrukcja

10 Grudnia 2024
Roland

Roland NEQ-H Instrukcja

10 Grudnia 2024
Roland

Roland Graphics Presenter Instrukcja

10 Grudnia 2024
Roland

Roland KD-18 Instrukcja

10 Grudnia 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

GBC

GBC ThermaBind T500Pro Instrukcja

15 Stycznia 2025
Da-Lite

Da-Lite Parallax 29850 Instrukcja

15 Stycznia 2025
Crivit

Crivit IAN 290909 Instrukcja

15 Stycznia 2025
Tripp Lite

Tripp Lite SmartRack SRW12US Instrukcja

15 Stycznia 2025
Powerfix

Powerfix IAN 280221 Instrukcja

15 Stycznia 2025
AGM

AGM Rattler TC35-640 Instrukcja

15 Stycznia 2025
AGM

AGM Wolf-7 Pro Instrukcja

15 Stycznia 2025
AGM

AGM Anaconda TC50-640 Instrukcja

15 Stycznia 2025
AGM

AGM Secutor Pro TS50-640 Instrukcja

15 Stycznia 2025
Microchip

Microchip AT91SAM9M11 Instrukcja

15 Stycznia 2025