Instrukcja obsługi Roland KD-A22

Roland Niesklasyfikowane KD-A22

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Roland KD-A22 (6 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/6
Owner’s Manual
Watch the Quick Start Video
“Installing the KD-A22”
http://roland.cm/kd-a22
Introduction
The KD-A22 can be installed on a 22-inch acoustic bass drum.
Fully assembled view
* A 22-inch acoustic bass drum is not included with this product.
When using a drum stand (MDS-50K/MDS-50KV)
For the MDS-50K/MDS-50KV, the spacing of the bass drum installation area
is as follows.
Vertical: 590 mm (23-1/4”)
Horizontal: 620 mm (24-7/16”)
620 mm
(24-7/16”)
590 mm
(23-1/4”)
Check the Included Items
After opening the package, check that all of the included items are
present. If anything is missing, contact your dealer.
Front head
Batter head
NOTE
Do not pull the cable that is attached to the batter head.
Batter board
NOTE
A circuit board is attached to the batter board. To prevent injury,
damage, or accident, observe the following points.
5
Do not touch the circuit board with your ngers.
5
Do not lay down the batter board with the circuit board facing
downward.
5
Do not apply excessive force to the circuit board.
Batter hoop
* Batter board spacers (6 pcs.) are
already attached
Batter board stopper x 4
Connection cable
Drum key
Before using this unit, carefully read “USING THE UNIT SAFELY” and
“IMPORTANT NOTES” (p. 6). After reading, keep the document(s) where it will
be available for immediate reference.
Copyright © 2016 ROLAND CORPORATION
2
Installing the KD-A22
Caution during installation
5
Before you begin the installation procedure, lay down a mat to
protect the oor or the drum from scratches.
5
When turning the bass drum upside down, take care not to drop
it or let it overturn.
5
Muting (such as using weights or a blanket) is not necessary.
Remove such materials from the bass drum. Also, do not install
muting after installing the KD-A22.
1. Attaching the Batter Head
1. Place the bass drum so that the striking surface head is
upward.
2. Loosen the lugs, and remove the hoop and head.
3. Place the batter head on the shell so that the hole in the
batter head is positioned as shown in the illustration.
NOTE
This placement of the batter head assumes that you are using
a single pedal. If you are using a twin pedal, you might need
to adjust the batter head hole position depending on the kick
pedal that you are using. For details, refer to “Using double kick
pedals” (p. 5).
Adjust the position of the batter
head so that the pin is aligned with
the center of the shell as shown in
the illustration.
Hole Pin
Top
Pin
4. Place the batter hoop on the batter head, and adjust the
position of the batter hoop so that the centers of the
batter hoop and batter head are aligned.
Place the batter hoop on the
batter head so that the pedal
attachment hardware is at this
location.
5. Move the batter board spacers attached to the batter
hoop to the positions shown in the illustration.
For a bass drum with eight lugsFor a bass drum with ten lugs
6. Working alternately across opposite sides of the drum,
lightly tighten each lug until the lugs do not wobble.
1
3
4
6
2
8
9
10
57
7. Then tighten each lug another 3/4 of a turn to secure the
batter head.
NOTE
If the batter head is not secured suciently, the sensor might
malfunction, or the sound of the strike might be too loud.
8. Move the batter board spacers attached to the batter
hoop in the directions shown by the arrows, so that they
rmly contact the lugs.
For a bass drum with eight lugsFor a bass drum with ten lugs
3
2. Attaching the Batter Board
1. Align the batter board’s circuit board cover with the hole
in the batter head, and place the batter board.
Hole
Circuit board cover
NOTE
Take care that the batter board’s circuit board cover does not
rest on the batter head or catch on the hole. Forcing it could
damage the circuit board/circuit board cover or the battery
head.
2. As shown in the illustration, align the center of batter
head’s strike surface and center of the batter board hole.
Align the center
Batter board
Striking surface of
the batter head
3. Lightly press down the batter board so that it rmly
contacts the batter head.
Batter board
Batter head
Batter board spacer
Batter hoop
Batter board spacer
3. Attaching the Batter Board Stoppers
Attach the included batter board stopper (4 pcs.) to the batter
hoop.
NOTE
When attaching the stoppers, take care not to hurt your hand
on the lugs.
1. Push down on the batter board stoppers in a location
where your hand will not strike the lug.
Batter board stopper
* It is easier to attach the
stoppers if you spread
them open as shown in the
illustration while pushing
them onto the batter hoop.
Press with the palm of your hand
Grasp this part
with your ngers
2. Position the batter board stoppers as shown in the
illustration.
For a bass drum with eight lugsFor a bass drum with ten lugs

Specyfikacje produktu

Marka: Roland
Kategoria: Niesklasyfikowane
Model: KD-A22

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Roland KD-A22, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Roland

Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024
Roland

Roland RD-300GX Instrukcja

13 Października 2024
Roland

Roland Fantom FA-76 Instrukcja

12 Października 2024
Roland

Roland M-1000 Instrukcja

12 Października 2024
Roland

Roland RD-88 EX Instrukcja

9 Października 2024
Roland

Roland VR-400UHD Instrukcja

7 Października 2024
Roland

Roland KD-200 Instrukcja

7 Października 2024
Roland

Roland DM-10 Instrukcja

5 Października 2024
Roland

Roland RD-08 Instrukcja

4 Października 2024
Roland

Roland RCP800 Instrukcja

4 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Florabest

Florabest HG05806 Instrukcja

15 Października 2024