Instrukcja obsługi Quoizel Dury RDY1717AWH

Quoizel Ulga Dury RDY1717AWH

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Quoizel Dury RDY1717AWH (2 stron) w kategorii Ulga. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/2
1of2
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
, .
. .
2018 QuoizelInc.
Assembly Instruction Sheet #IS-RDY1717AWH
For Style RDY1717AWH
ReleasedDate:2018-01-31
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
Please go to for product cleaning tips. Go to the selection.
(4) B10 Candelabra Base bulbs 60W Maximum.
30-45 minutes
Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
www.quoizel.com Care + Maintenance
Light Source:
Estimated Assembly Time:
Preparation:
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Package Contents
A
Crossbar
Assembly
x 1
B
Fixture
Body
x 1
C
Ceiling Canopy
with Nipple
x 1
D
Spacer Tube
x 1
STEP 1 Install Spacer Tube and Ceiling Canopy-
A. Pass the supply wires and ground wire from fixture through the
Spacer Tube (C) and the Ceiling Canopy with Nipple (B) in turn.
Place the nipple of the Ceiling Canopy with Nipple (B) through the
Spacer Tube (C) and thread the nipple onto the hex coupling on the
top center of the Fixture Body (D). Hand tighten until snug.
Figure 1
STEP 2 -Installing the Crossbar Assembly
A. Pass the supply wires with ground wire from outlet box through the
Crossbar Assembly (A). Attach the Crossbar Assembly (A) to the
Outlet Box with the head of the Green Ground Screw facing you.
Secure the Crossbar Assembly (A) with Outlet Box Screws (not
included). Tighten until snug.
Supply Wires
with Ground Wire
Figure 2
B
C
D
Hex Coupling
Outlet Box Screws
(not included)
Outlet Box
A
Supply Wires
with Ground Wire
STEP 3 -Test Fit the Ceiling Canopy to the Crossbar Assembly
A. Remove the mounting balls from the Crossbar Assembly (A). Place
the ceiling canopy onto the Crossbar Assembly (A) and secure with
mounting balls. Note: The ceiling canopy should be snug against the
ceiling and held tight with the mounting balls. If it is not, adjust the
length of the mounting screws on the Crossbar Assembly (A) by
unscrewing the preassembled hex nut and lock washer and then
screwing the mounting screws in or out of the crossbar until the
correct length is achieved. Once the ceiling canopy is secure,
remove the mounting ball and fixture and proceed to Step 4.
Mounting Screw
Hex Nut and
Lock Washer
Mounting Ball
A
Figure 3
Ceiling Canopy
2of2
2018 QuoizelInc.
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
ReleasedDate:2018-01-31
STEP 6 Install Bulbs-
A. Insert bulbs onto sockets and screw snugly into place.
Your fixture is now assembled and ready to use. Enjoy!
Socket
Bulb (not
supplied)
RDY1717AWH
NOTE: ALL DIMENSIONS ARE ROUNDED UP
TO THE NEAREST 1/4"
Figure 6
5.5” Dia.
16.25
17.5” Dia.
FINISH: ANTIQUE WHITE
STEP 5 Install the Fixture
Body
-
A. Position the ceiling canopy
and fixture body onto the
Crossbar Assembly (A).
Place the holes in the ceiling
canopy over the mounting
screws. Secure the fixture
body by using the mounting
balls and hand tighten the
mounting balls until snug.
Figure 5
Mounting
Screw
Mounting Ball
A
Ceiling
Canopy
STEP 4 - Wire Connections
A.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
Figure 4
Green Ground Screw
on the Crossbar
White wire
from outlet box White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture


Specyfikacje produktu

Marka: Quoizel
Kategoria: Ulga
Model: Dury RDY1717AWH

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Quoizel Dury RDY1717AWH, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Ulga Quoizel

Instrukcje Ulga

Najnowsze instrukcje dla Ulga

Goobay

Goobay 30780 Instrukcja

15 Października 2024
QTX

QTX DM-X12 Instrukcja

15 Października 2024
Livarno

Livarno IAN 94799 Instrukcja

15 Października 2024
Astro

Astro Denia Instrukcja

13 Października 2024
AFX

AFX Grace GRCP07CBBK Instrukcja

12 Października 2024
AFX

AFX Point PNTP0107L30D1BK Instrukcja

12 Października 2024
Neewer

Neewer TL97C Instrukcja

9 Października 2024
Neewer

Neewer SRP18C Instrukcja

9 Października 2024
Ikea

Ikea STRÅLA 005.824.56 Instrukcja

9 Października 2024
Ikea

Ikea STRÅLA 705.829.38 Instrukcja

9 Października 2024