Instrukcja obsługi QTX UV Cannon 160.028UK

QTX Ulga UV Cannon 160.028UK

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla QTX UV Cannon 160.028UK (3 stron) w kategorii Ulga. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/3
1/1
400W BLACK LIGHT
160.028
USER MANUAL
INTRODUCTION
Congratulations on the purchase of your new our company lighting effect. We are confident you will enjoy
many trouble free hours with this unit . To assist with the care and use of the product we have prepared this
short guide.
OPERATION
Before connecting this unit to the mains power supply for the first time you must first install the lamp .
(See ‘Replacing Lamp’ for details).
This lighting effect has been designed to function on a mains power supply of either 240V~50Hz and has been
fitted with a suitable power plug for use with your local voltage. Check the label on the unit and the power plug
for the correct voltage.
When connected to the mains power supply the unit should illuminate. The 160.028 utilizes a mercury vapor
lamp ,it will take 5 to 10 minutes to reach full intensity . The intensity of the lamp will increase with use. The
light emitted by the 160.028 is invisible and does not have the glow of a fluorescent fixture.
Due to the high operating temperature of halogen lamps it is advisable that the effect be used in well ventilated
areas taking care not to obstruct the air vents. To maximize lamp life, allow the unit to cool down before
moving or touching the lamp.
CAUTION
Due to the nature of the mercury vapor lamp, this lamp must be allowed to cool down (about 5 to10 minutes)
after being turned off before re-igniting. Failure to wait for cool down many cause the lamp to fail prematurely.
INSTALLATION/MOUNTION
Although this unit can be used in an upright position , it is recommended that , for safety purposes ,your
lighting effect be properly mounted using a suitable hanging clamp and safety cable . Our company offers a
range of items , which are ideal for safe mounting .
Use in a well-ventilated area without obstruction to air vents.
2/2
REPLACING LAMPS
1. Disconnect from main power supply before attempting to replace either lamp .
2. Ensure that the unit is sufficiently cool , before removing blown lamps.
3. Never touch new lamps with your fingers: use a tissue or a cloth.
In order to replace the lamp, disconnect from main power supply rst, and unscrew the lamp replacement cover.
Only use the appropriately rated lamps as use of any other lamp type many cause the unit to be non-operational.
Due to the nature of halogen lamp it is vitally important that you do not touch the new replacement lamp with
your fingers, as this will reduce lamp life considerably. Once again a tissue or cloth can be used for fitting the
replacement lamp.
If after replacement of the lamp, the unit is still not working then please contact your dealer or our company for
servicing.
CLEANING
The most important part of your lighting effect to keep clean is the reflector as it allows the light output to
transmit. This should be cleaned with a soft damp cloth. The body of the unit may also be cleaned in the same
way . We recommend internal cleaning be carried out by a fully qualified technician.
MAINTENANCE & SERVICING
Work on internal parts should be carried out by a qualified technician. Removal of covers other than the front to
replace lamp is considered a breach of warranty and will not be covered under any such agreement unless
authorized first by the company.
TROUBLESHOOTING
• If the unit is not functional-check main power supply is ‘on’.
• If the unit is functional but lamp does not light-lamp may require replacing.
• If after trying this solution you still have a problem contact your dealer or our company for service.
CAUTION
Do not obstruct the air vents.
Do not touch unit or lamps while hot.
Never put any objects through the air grill on the top of the unit.
No user serviceable parts inside, please refer to our company.
POWER CONNECTIONS
The unit is supplied with a power plug appropriate to its voltage and destination. Should any other connections
be required they must be carried out with the following configuration.
Earth = Green/Yellow cable
Neutral = Blue cable
Live = Brown cable
3/3
In the USA & Europe, it is required that all plugs are 3-pin type i.e. with Earth/Ground connection.
In the UK, it is required that all mains plugs are fitted with 5A fuses.
TECHNICAL SPECIFICATIONS
Power 240V~50Hz AC
Lamps E40 400W Mercury Vapor
Part No H400BL
Fuse 250V/5A
imensionsD 375x388x413mm
Weight 13.5kg

Specyfikacje produktu

Marka: QTX
Kategoria: Ulga
Model: UV Cannon 160.028UK

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z QTX UV Cannon 160.028UK, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Ulga QTX

QTX

QTX DM-X12 Instrukcja

15 Października 2024
QTX

QTX HPWash100 Instrukcja

6 Października 2024
QTX

QTX Moonglow Instrukcja

6 Października 2024
QTX

QTX Recharge Performer Instrukcja

27 Września 2024
QTX

QTX Wash & Beam Instrukcja

27 Września 2024
QTX

QTX TetraCube Instrukcja

27 Września 2024
QTX

QTX BATPAR-18W Instrukcja

27 Września 2024
QTX

QTX TinyMover Instrukcja

27 Września 2024
QTX

QTX Recharge DJ Instrukcja

27 Września 2024
QTX

QTX Multi-Bar Instrukcja

27 Września 2024

Instrukcje Ulga

Najnowsze instrukcje dla Ulga

KonstSmide

KonstSmide 7860-370 Instrukcja

15 Stycznia 2025
Gardena

Gardena 4206 Instrukcja

15 Stycznia 2025
Nedis

Nedis WIFILS52CRGBW Instrukcja

15 Stycznia 2025
Philips

Philips HF3304 Instrukcja

14 Stycznia 2025
Nedis

Nedis BTTNTP-22W60 Instrukcja

14 Stycznia 2025
Nedis

Nedis BTTNTP-44W120 Instrukcja

14 Stycznia 2025
Livarno

Livarno IAN 103915 Instrukcja

13 Stycznia 2025
ION

ION Party Ball USB Instrukcja

13 Stycznia 2025
Livarno

Livarno IAN 292038 Instrukcja

12 Stycznia 2025
Eurolite

Eurolite LED TMH-17 Instrukcja

12 Stycznia 2025